CHiQ Bottom Mount Refrigerator

Part Names and Locations

The refrigerator is depicted with numbered components. The top section shows the interior of the fridge compartment with shelves and a crisper. The door of the fridge compartment has shelves. The bottom section shows the freezer compartment with drawers.

In Accessory Bag

USER MANUAL, WARRANTY CARD, EGG TRAY, ICE BOX & DOOR STOPPER (small plastic parts for door reverse purpose ONLY)

As the manufacturer holds the authority to redesign or modify its products without notice: Any modifications or upgrades of our products will result in this refrigerator varying slightly from this manual but the functionality will remain the same to that as set out within this manual.

Important Safety Instructions

⚠️ Follow these basic precautions to reduce the risk of fire, electrical shock hazards or injury when operating the refrigerator:

• This product has been designed for using in a normal domestic environment. It is not intended for commercial use which will avoid warranty, such as supermarket, food shop, pharmacy, commercial kitchen & etc.
• Persons with lack of experience and knowledge, reduced physical or mental capabilities, need to be given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• It is critical use this appliance safely. Read all instructions before operating the refrigerator and do not attempt to repair or modify this unit in any way as it can cause harm or void the warranty.
• Please ensure all persons using this appliance are also informed and comply with the details set out within this manual and the product Terms and Conditions.
• When unpacking the appliance for the first time, keep all cardboard and plastic packaging out of reach from children.
• Report any notable defects with the appliance to Chiq or retailer as soon as it is noted. Failure to do so can result in a non-warranty claim. Keep all packaging materials in a safe location until the unit has been installed properly.
• If the supplied power cord of this unit is damaged, it must be replaced by qualify service agent or similarly qualified persons in order to avoid any risk of injury. It is recommended the power cord is situated in a safe location when operating or transporting the appliance to prevent any damage that may cause electrical shock or fire hazards.

DANGER or WARNING:

Service of this unit

The installation or any service of the appliance is recommended by a qualified technician or service company.

Ventilation Hazards

Never clean the refrigerator or refrigerator parts with flammable fluids, or store gasoline or any other flammable vapors and liquids in the vicinity of this or any other refrigerator as the gas and/or vapour can cause a fire hazard, explosion or inhalation.

Electrical Connection

Make certain, when installing or moving the unit that the power outlet has been connected to, has been fitted by a qualified electrician and the ground wire has been connected properly to meet the Australian Electrical Standards.

R600a WARNINGS

NOTE: This model uses R600a flammable refrigerant in its sealed system. The following must be observed for your safety:

R600a Refrigerant Warning

• This appliance contains 0.039kg R600a refrigerant which is environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the greenhouse effect.
• During transportation and installation, ensure that the tubing of the refrigerant circuit is not damaged.
• Leaking refrigerant can ignite and may damage the eyes.
• In the event any damage does occur, avoid exposure to open fires and any device which creates a spark. Disconnect the appliance from the mains power.
• Thoroughly ventilate the room in which the appliance is located for several minutes.
• Notify Customer Service for necessary action and advice.
• The room for installing the appliance must be at least 1 cubic metre per 8 grams of refrigerant. The refrigerant quantity contained in this appliance is listed above in grams; it is also noted on the Rating Plate of the appliance.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

It is hazardous for anyone other than an Authorised Service Person to carry out servicing or repairs to this appliance. In Queensland the authorized person must hold a Gas Work Authorisation for hydrocarbon refrigerants, before carrying out servicing or repairs which involve the removal of covers.

1. Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
2. Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
3. Do not damage the refrigerant circuit.
4. Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
5. Do not store explosive substances such as aerosol cans with a flammable propellant in the appliance.

Disposal

The environment and personal safety must be considered when disposing of this appliance. Please ensure the appliance is taken to a recycle center for safe recycling. DO NOT dispose of the appliance in land fill as the insulation and refrigerant gas contained in these appliances are flammable.

Door Reversal Instruction

It requires a door stopper in accessory bag for door reversal job. The following tool is required: flat screwdriver, phillips screwdriver, adjustable spanner, socket wrench and 8mm socket.

If the appliance is placed on its back or side during this process it must be allowed to stand upright for 6 hours before plugging in to avoid damage to internal components.

1. Remove the screw hole cover from the top left side of the cabinet. Remove the upper hinge cover and the upper hinge from the top right side of the cabinet. Remove the freezer door from the cabinet.
2. Remove the center hinge from the right side of the cabinet. Remove the refrigerator door from the cabinet. Remove the screw hole covers from the left side of the cabinet. Remove the refrigerator door from the cabinet.
3. Remove the lower hinge from the bottom right side of the cabinet.
4. Remove the pin shaft to the right hole on the lower hinge, then insert the pin shaft into the left hole on the lower hinge.
5. Install the lower hinge onto the lower left side of the cabinet.
6. Remove the freezer door stop from the lower right side to the left side of the door. Get the left door stoop from the accessory bag, install it on bottom left side of the refrigerator door.
7. Move the door bushing from the top right side of the refrigerator door and remove the hinge hole cover from the top left side of the door. Exchange their positions.
8. Install the freezer door onto the cabinet. Install the center hinge on the left side of the cabinet. Install the screw hole covers on the right side of the cabinet.
9. Install the refrigerator door onto the cabinet. Install the upper hinge on the top left side of the cabinet. Install the screw hole cover onto the top right side of the cabinet.

Note: These instructions reference the models that come from the factory with a right hand swing door. If your appliance comes with a left hand swing, ensure that you flip the "left" and "right" in these instructions.

Installation Instructions

Before Using the Refrigerator

• Remove the exterior and interior packing.
• Before connecting the refrigerator to a power source, let the unit stand upright for approximately 4 hours to mitigate the possibility of a malfunction in the cooling system from improper handling during transportation.
• Clean the interior surface with warm water using a soft cloth.

Installing the Refrigerator

• This appliance is designed to be free standing only, and should not be recessed or built-in.
• Allow at least 5cm of space between the back and sides of the refrigerator to allow proper air ventilation. Insufficient space will result in cooling and working life issue and voiding warranty.
• Place the refrigerator on a leveled/even floor surface that is strong enough to support the weight of the refrigerator when it is fully loaded to prevent vibrations.
• Place the refrigerator on a concrete, tile floor or waterproof floor is recommended. The fridge will produce defrost water or condensation moisture, it might cause water damage in some extreme circumstances.
• The front feet can be adjusted to level the appliance properly. Adjust the two front feet to keep the refrigerator leveled or elevated.
• Situate the refrigerator away from direct sunlight and sources of direct heat (stove, heater, radiator, etc.). Direct sunlight may also affect the acrylic coating and heat sources may cause an increase power consumption.
• This unit is not designed for outside installation.
• Avoid situating the refrigerator in moist OR pest infestation areas.
• Plug the refrigerator into dedicated, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized service center.
• After plugging the appliance into a wall outlet, turn the unit on and allow the unit to cool down for 4-6 hours before placing food in the refrigerator.
• Do not place heavy items on the top of this appliance.

Energy Saving Tips

• Allow hot foods to cool to room temperature before placing in the refrigerator. Overloading the refrigerator forces the compressor to work harder. Foods that freeze too slowly may lose quality, or spoil.
• Be sure to wrap foods properly, and wipe containers dry before placing them in the refrigerator. This cuts down on frost build-up inside the refrigerator.
• Organize and label food to reduce door openings and extended searches. Remove as many items as needed at one time, and close the door as soon as possible.

Operating Instructions

START

When the refrigerator has power on for the first time, the indicator lights of display area fully illuminated for 2 seconds. After that, the refrigerator will run at setting 4 by default.

Temperature Adjustment Setting

There is a temp setting panel on the top of the fridge compartment.

The temperature setting panel has controls labeled 'FAST COOL', '5 coldest', '4', '3 RECOMMEND', '2', '1 warmest', and a 'SET' button.

Temperature can be adjusted by pressing the SET key. The temperature adjustment cycles in the following mode: 5→4→3→2→1→FAST COOL→5.

Temp setting on No.5 will be coldest and number 1 will be warmest. Please note the number doesn't mean the exact temperature in the fridge. It just a temperature setting range.

Adjust the temp setting will change freezer and refrigerator temperature together. Number 3 setting is recommended for normal use condition.

FAST COOL

The refrigerator can be set on fast cool mode, as to ensure keeping food nutrition and freshness. The Fast Cool function can keep working for a maximum period of 30 hours. After that, it will automatically quit the model and set to previous temp setting.

Freezer Air Flow Adjustment

The air flow adjustment panel shows 'MIN REFRIGERATOR MAX' and 'COLDEST MAX FREEZER MIN'. There is a knob that can be adjusted between MIN and MAX for both refrigerator and freezer sections. A 'RECOMMEND TEMP.CONTROL' indicator is also present.

All cold air is coming from freezer compartment, there is an air flow adjustment knob on the back panel.

With same Temperature adjustment setting:

1. Adjust freezer air flow knob to left hand side position that will allow more cold air to stay in freezer part, therefore the freezer will be more colder.
2. Adjust it to right hand side position that will allow more cold air to go up to refrigerator compartment which will be more colder.

To balance the air flow, please put the knob in the middle position for normal working condition. If the fridge part isn't cold enough, please adjust it close to right hand side position. Please don't put it on Very left position for long time to avoid building up too much ice in freezer.

Failure Alarm

When the indicator light of Mode 2 or Mode 5 keeps flashing, it indicates the refrigerator failure. Please contact customer service for assistance.

Humidity Control

The crisper has a Humidity control on the front, set it to high (three water drop symbol ??? on left position) will keep more moisture inside and set it to Low (one water drop symbol ? on right position) position will reduce the moisture.

If too much moisture or condensation under the crisper glass cover. Please put leafy greens, like arugula, spinach, and herbs into a plastic or paper bag before putting the crisper.

Notes

• Large quantities of food stored in the appliance or directly in front of the air vent will hinder the cooling efficiency of the appliance as this can affect the airflow.
• Change the thermostat settings in the fridge or freezer compartment, allow 6 hours for temperature to stabilize between adjustments.
• Do not keep opening and closing the door which will increase the temperature in the unit.
• Please note different sections of refrigerator compartment may be warmer or cooler than others – typically the back wall and bottom lowest shelf will be the coolest, the top door rack will be the warmest. To avoid frost bite, please don't put raw vegetables too close to the coolest area.

General Care and Maintenance

Cleaning the Refrigerator

• Upon installation of your new appliance, it is recommended that it be cleaned thoroughly and properly maintained thereafter.
• Turn off the refrigerator and then unplug the unit from the wall outlet.
• Remove all food content before washing the inside with a damp cloth soaked in lukewarm water and dishwasher liquid. Don't use any chemical detergent which might damage coating of the fridge.
• Be sure to keep the door gasket (seal) clean to keep the unit running efficiently as improper cleaning can cause the seal to dislodge and tear.
• Dry the interior and exterior with a soft cloth.

Vacation Time

• Turn off the refrigerator first and then unplug the unit from the power point.
• Remove all food.
• Clean the refrigerator.
• Leave the lid open slightly to avoid possible formation of condensation, mold, or odors.
• Use extreme caution in the case of children. The unit should not be accessible to child's play.
• Short vacations: Leave the refrigerator operating during vacations of less than three weeks.
• Long vacations: If the appliance will not be used for several months, remove all food and unplug the power cord. Clean and dry the interior thoroughly. To prevent odour and mold growth, leave the door open slightly: blocking it open if necessary.

Repositioning and Relocating the Refrigerator

• Unplug the power cord from the wall outlet.
• Remove all the food and drinks.
• Securely tape down all loose items inside your refrigerator.
• Tape the doors to be closed securely.
• It is recommended that the refrigerator stays in the upright position during transportation. But if it is laid down for transport purpose, please lift it up immediately after the job is done. Please wait for at least 24 hours before putting the power.

Troubleshooting Guide

For any enquiries, please call the CHiQ Customer care on: 1300 796 688