Basin Faucet Installation Guide

Product Overview

This document provides installation, maintenance, and warranty information for basin faucets, specifically models M2210, M1392, and M1394, identified by codes SFS-1113, SFS-1116, and SFS-1118 respectively.

Warranty Information

Warranty Duration

All components of this faucet system are covered under a lifetime limited warranty, ensuring they are free from defects in material and workmanship for the original purchaser.

Repair and Replacement

If the product shows defects in material or workmanship under normal use and within the warranty period, the manufacturer will, at its discretion, either repair the product or provide a replacement at no cost to the original purchaser. Proof of purchase (e.g., an invoice) is required when requesting service. The warranty does not cover damages caused by improper installation, misuse, or modifications.

Exclusions

The manufacturer shall not be responsible for the following cases:

• Damage to the product caused by improper installation, misuse, unauthorized repair or replacement, or abuse (including damage during shipment).
• Damage to the product caused by improper dismantling after installation.
• Damage resulting from abnormal water pressure or impurities in water pipes.
• Rust on the product due to insufficient care and maintenance.
• Damage caused by natural disasters such as fire, flood, earthquake, lightning storms, etc.

Installation Instructions

The following steps detail the installation process for Basin Faucet Models A, B, and C.

Step 1: Countertop Preparation

Drill holes in the countertop according to the specified dimensions.

Diagram Description: A countertop is shown with two holes drilled. Arrows indicate lowering the faucet body onto these holes. Dimensions provided are: 101mm (4") for the horizontal center distance between the two holes, and φ21mm (7/8") for the diameter of each hole.

Note: The horizontal center distance between the two holes must be 101mm (4"). Otherwise, the faucet cannot be installed on the countertop.

Align the Basin Faucet Body with the hole positions and install it onto the countertop following the direction shown in the diagram.

Diagram Description: The Basin Faucet Body, noted as pre-assembled and requiring no disassembly, is shown being lowered onto the prepared countertop holes.

Step 2: Connecting Inlet and Outlet Pipes

Part Attachment: Connect the Faucet Body Gasket and Faucet Body Nut to the Basin Faucet Body in sequence, following the direction shown in the diagram, until tightened.

Diagram Description: This step illustrates attaching the Faucet Body Gasket and Faucet Body Nut to the base of the faucet body.

Hose Connections:

Diagram Description: The faucet is shown installed on the countertop. Two flexible hoses (one for hot water, one for cold water) are connected to the underside of the faucet body. These hoses then connect to corresponding angle valves under the countertop. Arrows indicate the flow direction: "Hot Water Inlet" and "Cold Water Inlet".

1. Connect one end of the hot and cold hoses to the faucet body respectively. (Note: Hot water connection is on the left, cold water connection is on the right).
2. Connect the other end of the hot and cold hoses to the corresponding angle valves controlling hot and cold water respectively.
3. Turn on the angle valves. Open the faucet handle to control the water flow. Check if the water flows normally and inspect for leaks at all connection points.

The installation method for models ABC is similar; please refer to the actual appearance of the product.

Parts List

The following tables list the standard parts included for each basin faucet model.

Model: A (SFS-1113)

Diagram Description: An illustration shows the components of the basin faucet, with numbers corresponding to the parts list. The main faucet body is labeled '1'. Other parts include gaskets ('2'), nuts ('3'), and hoses ('4'). Smaller icons represent the manual ('5'), gloves ('6'), and adapter ('7').

Model: B (SFS-1116)

Diagram Description: An illustration shows the components of the basin faucet, with numbers corresponding to the parts list. The main faucet body is labeled '1'. Other parts include gaskets ('2'), nuts ('3'), and hoses ('4'). Smaller icons represent the manual ('5'), gloves ('6'), and adapter ('7').

Model: C (SFS-1118)

Diagram Description: An illustration shows the components of the basin faucet, with numbers corresponding to the parts list. The main faucet body is labeled '1'. Other parts include gaskets ('2'), nuts ('3'), and hoses ('4'). Smaller icons represent the manual ('5'), gloves ('6'), and adapter ('7').

Maintenance and Care

Installation and Maintenance Matters

1. Check the accessories list to verify that all parts are complete in this package.
2. Do not disassemble the main body by yourself. ??
3. Connect inlet pipes to supply valves.
4. Make sure inlet pipes and supply valves have no impurities and are cleaned, with no impurities in the pipeline.
5. After installation, check all joints for leakages.
6. Do not leave the basin faucet exposed to a severely corrosive environment. ☣️

Do's

1. To keep the mixer surface bright, clean the mixer regularly.
2. Rinse the faucet with clean water and wipe it with a soft cotton cloth.
3. Use one of the following cleaners to remove dirt from the surface:
   • a. Mild liquid cleaner.
   • b. Colorless glass cleaner and powder cleaner that do not cause abrasion and can be dissolved completely.
   • c. Polish liquid that does not cause abrasion.

Don'ts

1. Avoid using cleaning powder, harsh cleaning chemicals, brushes, and coarse cloth to prevent scratching and friction.
2. Do not use acid cleaners to clean the faucet, as they may cause surface corrosion. If the faucet is exposed to harmful acid substances, rinse it immediately with water. ?

Tools Needed

• Safety glasses ?
• Allen wrench ?
• Pipe wrench ?
• Screwdriver ?
• Sealant/Tape ?
• Adjustable wrench ?
• Soldering torch ? (or heat source)

Diagram Description: A collection of tools typically used for plumbing installations is displayed, including safety glasses, various wrenches, a screwdriver, and a torch.

Contact Information

If you have any further questions or concerns, please contact:

Email: info@faucetsupport.com

Toll Free: 1-888-969-6880