HDMI® WIRELESS EXTENDER/ RECEIVER

Dear Customer

Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.

This product is 100% inspected and tested in the United States to verify HDMI performance parameters.

WARNING

• Do not expose this unit to water, moisture, or excessive humidity.
• Do not install or place this unit in a built-in cabinet, or other confined space without adequate ventilation.
• To prevent risk of electrical shock or fire hazard, due to overheating, do not obstruct unit's ventilation openings.
• Do not install near any source of heat, including other units that may produce heat.
• Do not place unit near flames.
• Only clean unit with a dry cloth.
• Unplug unit during lightening storms, or when not used for an extended period of time. A surge protector is strongly recommended.
• Protect the power cord from being walked on or pinched, particularly at the plugs.
• Use unit only with accessories specified by the manufacturer.
• Refer all servicing to qualified personnel.

CAUTION

HDMI is a very complex technology requiring continuous authentication of the signal and the same video resolution and audio settings on all electronic equipment in the system. When there are multiple sources and displays, the video resolution and audio setting on all connected units must be adjusted to correspond with that of the display having the lowest video and audio capability.

Features

The Vanco HDWIRKIT/RX extends HDMI signals wirelessly from a source to a display up to 131ft/40m using wireless technology. There are no cables required between the transmitter and receiver, making for a clean and easy installation, especially where cabling is difficult or impossible to run. Using a 5GHz operation frequency, the HDWIRKIT Transmitter and Receiver do not require line of sight transmission; the wireless signal will travel through most obstacles with no issues. Out of the box, the HDWIRKIT works as a point-to-point configuration, but also supports having multiple sets on the same site (up to 10) and one-to-multiple (1 TX to up to 4 RX) displays using HDWIR-RX receivers (sold separately). It is a great solution for splitting a single source signal wirelessly. It also features dual-band IR call back to control the source from any display location connected. With the ability of sending HDMI signals wirelessly, whether point-to-point or splitting to multiple displays, the HDWIRKIT and optional HDWIR-RX are easy solutions where running cable is an issue.

HDMI® WIRELESS EXTENDER/RECEIVER

• Part #: HDWIRKIT (transmitter and receiver)
• Part #: HDWIR-RX (receiver only)
• Extends HDMI signals wirelessly up to 131ft/40m
• Transmits up to 1080p HD video and audio
• Kit includes both Transmitter and Receiver for point-to-point application
• Able to split wireless HDMI signals to up to 4 displays (additional HDWIR-RX receivers sold separately)
• Multiple kits can be installed in one application without interference
• Perfect solution where cabling cannot be run, such as a mantle or outdoor application
• IR pass-through to control source from display location wirelessly
• Wireless 5 GHz frequency
• No line of sight installation required; wireless signal will pass through most obstacles
• Easy manual front panel or IR setup for multiple units
• Dimensions: 5.25" W x 0.75" H x 3" D

Specifications

Package Contents

Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton:

• Wireless Transmitter (HDWIRKIT only)
• Wireless Receiver
• 5V/2A Power Supply
• IR Blaster (TX)
• IR Receiver (RX)
• IR Remote Control
• Product Manual

Panel Descriptions - Transmitter

1. Antennas: For wireless signal transmission and reception.

2. RF Channels (Selectable 0-9): Used to "marry" to a receiving unit or to split signals to multiple HDWIR-RX receivers. Ensure transmitter and receiver(s) are set to the same channel.

3. Channel Toggle Switch: Sequentially cycles through RF Channels 0-9.

4. IR Sensor: Receives IR signals from the included remote control to change RF channels remotely.

5. Reset Button: Resets the unit. Press to resolve connection issues.

6. DC 5V Power Supply Port: Connect the included 5V/2A power adapter here.

7. HDMI INPUT: Connect your HDMI source device here.

8. Signal Status Indicator: Solid Green indicates a successful signal connection to the source.

9. Syncing Status: Blinking Green indicates connection to a receiving unit. Solid Green indicates no connection to a receiver.

10. HDMI OUT (Loop-out): Allows connection to a local display, such as a control room monitor, for simultaneous viewing.

11. IR OUT: Connect the included IR Blaster (TX) here. Position the blaster near the source device's IR sensor for IR control.

Panel Descriptions - Receiver

1. Antennas: For wireless signal transmission and reception.

2. RF Channels (Selectable 0-9): Used to "marry" to a transmitting unit. Other receivers can be set to the same RF channel to split the signal. Ensure receiver and transmitter are set to the same channel.

3. Channel Toggle Switch: Sequentially cycles through RF Channels 0-9.

4. IR Sensor: Receives IR signals from the included remote control to change RF channels remotely.

5. Reset Button: Resets the unit. Press to resolve connection issues.

6. DC 5V Power Supply Port: Connect the included 5V/2A power adapter here.

7. Signal Status Indicator: Solid Green indicates a successful signal connection from the transmitter.

8. Syncing Status: Blinking Green indicates connection to a transmitting unit. Solid Green indicates no connection to a transmitter.

9. HDMI OUTPUT: Connect your HDMI display or sink device here.

10. IR IN: Connect the included IR Receiver (RX) here. Position the receiver near the display for controlling the source device.

Connect and Operate

1. Connect an HDMI cable from your source device into the HDMI INPUT port of the TRANSMITTER.
2. OPTIONAL: Connect the provided IR BLASTER into the IR OUT port of the TRANSMITTER.
3. OPTIONAL: Connect an HDMI cable to the HDMI OUT (Loop-out) port to connect to a local display, such as a control room display.
4. Connect an HDMI cable from the HDMI OUTPUT port of the RECEIVER to your display or sink device.
5. OPTIONAL: Connect the provided IR RECEIVER into the IR IN port of the RECEIVER.
6. Connect both power supplies to the TRANSMITTER and RECEIVER using the provided power supplies. Connect the TRANSMITTER first, followed by the RECEIVER.
7. Using the manual toggle buttons on the units or the provided IR remote control, select any available channel. The TRANSMITTER and RECEIVER MUST be on the same channel. If using multiple kits, set each kit to different channels to avoid signal interference.

NOTE: If there is no signal on startup, press the RESET button on the TX and/or RX.

NOTE: Transmission distance may differ based on certain environmental factors such as other wireless signals that can interfere with transmission. Solid core walls, brick, or glass can significantly shorten the range at higher resolutions.

IR Pass-Through

The IR system allows you to control the source device connected to the extender unit from the display location. There are two important things to note when setting up the IR system:

1. The IR Receiver (IR RX) is what you point your remote control at to send an IR signal. This pigtail is placed at the display location for controlling the source.
2. The IR Blaster (IR TX) is what sends the IR signal to the device you intend to control. This pigtail is placed at the source device, either pointed at the source's IR sensor, or placed on the front panel of the source. See below for placement tips.

IR Blaster (TX) Placement

To control the source: plug the IR Blaster into the IR OUT port of the TRANSMITTER. Place the blaster in front of the IR eye of the source device.

Note: Placement of the IR Blaster is critical and can result in the IR system not working if improperly placed.

Placement Tips:

• First, locate the IR eye or window on the source device.
• If placing the IR blaster directly on the front panel of the source, do not stick it directly on top of the IR eye or IR window. The IR signal cannot travel through the double-sided tape on the Blaster. Instead, place the blaster on either side, or on the top or bottom of the IR eye or window, with the tip of the blaster facing the IR eye or window.
• The diagram illustrates that the IR signal emits from the tip of the IR Blaster. Ensure this tip is aimed towards the source's IR receiver.

IR Receiver (RX) Placement

To control the source: Plug the IR Receiver into the IR IN port of the RECEIVER. Place the receiver at or near the display.

Note: Due to possible differences in 3rd party IR cables, please use the IR cables that came with the product.

Troubleshooting

1. Display shows "waiting for connection": Check if the power supplies for the transmitter and receiver are well connected and that the power indicator lights are ON.
2. Display states, "Please check the TX input signal...": First, check if the input signal is properly connected and powered on. Next, try connecting the signal source directly to the display device to see if there is a signal output from the source device, or try changing the signal source.
3. Display is not stable:
   • Try moving the position of the transmitter and receiver and ensure the device's range has not been exceeded.
   • Press the "RESET" button on the RX first, followed by the TX. Allow time for syncing before trying the TX RESET button.
   • Remove power and HDMI cables from both units, reconnect the HDMI cables FIRST, then reconnect power.
   • Try to remove or minimize other wireless signals that may be disrupting the transmission.

Safety and Notice

The HDWIRKIT/HDWIR-RX has been tested for conformance to safety regulations and requirements and has been certified for international use. However, like all electronic equipment, the HDWIRKIT/HDWIR-RX should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.

• Follow all instructions and warnings marked on this unit.
• Do not attempt to service this unit yourself, except where explained in this manual.
• Provide proper ventilation and air circulation and do not use near water.
• Keep objects that might damage the device and ensure that the placement of this unit is on a stable surface.
• Use only the power adapter and power cords and connection cables designed for this unit.
• Do not use liquid or aerosol cleaners to clean this unit.
• Always unplug the power to the device before cleaning.

Limited Warranty

With the exceptions noted in the next paragraph, Vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of two years from the date of purchase. Should this product, in Vanco's opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco.

This warranty does not apply to those products which have been damaged due to accident, unauthorized alterations, improper repair, modifications, inadequate maintenance and care, or use in any manner for which the product was not originally intended.

Items integrated into Vanco products that are made by other manufacturers, notably computer hard drives and liquid crystal display panels, are limited to the term of the warranty offered by the respective manufacturers. Such specific warranties are available upon request to Vanco. A surge protector, power conditioner unit, or an uninterruptible power supply must be installed in the electrical circuit to protect against power surges.

If repairs are needed during the warranty period, the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement.

Liability Statement

Every effort has been made to ensure that this product is free of defects. The manufacturer of this product cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use. It is the responsibility of the user and installer of the hardware to check that it is suitable for their requirements and that it is installed correctly. All rights are reserved. No parts of this manual may be reproduced or transmitted by any form or means electronic or mechanical, including photocopying, recording or by any information storage or retrieval system without the written consent of the publisher.

Manufacturer reserves the right to revise any of its hardware and software following its policy to modify and/or improve its products where necessary or desirable. This statement does not affect the legal rights of the user in any way.

Technical Support

In case of problems, please contact Vanco Technical Support by dialing 1-800-626-6445. You can also email technical support issues to techsupport@vanco1.com.

When calling, please have the Model Number, Serial Number (affixed to the bottom of the unit) and Invoice available for reference during the call.

Please read this Instruction Manual prior to calling or installing this unit, as it will familiarize you with the capabilities of this product and its proper installation.

All active electronic products are 100% inspected and tested to ensure the highest product quality and trouble-free installation and operation. The testing process utilizes the types of high-definition sources and displays typically installed for entertainment and home theater applications.

For additional information, such as helpful installation videos, glossary of terms, etc., please visit vanco1.com.

Vanco International

506 Kingsland Drive Batavia, Illinois 60510
Call: 800.626.6445 | Fax: 630.879.9189 | Visit: www.vanco1.com