Regulatory Information
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the transmitter's radiating structure(s) and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user's authority to operate the equipment.
Contains FCC ID: 2AU5D-WRCB4
IC Notice
This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 20 cm to the human body. Note: Any changes or modifications to this device that are not expressly approved by the manufacturer, will void the warranty and the user's authority to operate the equipment.
IC: 25764-WRCB4
HVIN: WZ3RCB4
Before You Start
⚠️ WARNING:
Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
⚠️ CAUTION:
To reduce the risk of injury and/or overheating and damage to other equipment:
- For dry, indoor use only.
- Do not use to power medical equipment - not suitable as a disconnecting means.
You May Need
- Phillips-head screwdriver
- Flat blade screwdriver
- Voltage tester
- Pliers
- Wire cutter
- Wire stripper
- Electrical tape
- Wire nut
Installation
1. Choose a place to install the device
This device can be installed on a flat wall surface or in any standard U.S. electrical wall box. It may also be installed over the wall next to a standard U.S. electrical wall box, if used with a multi-gang Legrand radiant wall plate (catalog number beginning with RWP26-XXX).
Installation (on a wall surface)
- Use provided double-sided stickers to install on a tiled or other smooth surface. Markings on the back of the device indicate sticker locations.
- Use provided mounting screws to install on drywall or uneven surfaces where stickers may not work. Do not remove the label or pull out the ground wire, as the device may not sit flush.
Installation (in an electrical box)
Refer to Diagram A.
Step 1: Turn off power to the box at the circuit breaker.
Step 2: Ensure power is off to all devices in the electrical box. Remove the old device. Install wire nuts to terminate all exposed wires previously connected to the old device. Ensure complete electrical insulation by securing wire nuts, making sure no bare wire is exposed.
Step 3: Install and secure the device:
- Fold the wires into the electrical box, taking care not to pinch a wire.
- Remove the label on the back of the device to expose the ground wire and connect it to the box ground.
- Use included mounting screws to secure the device to the electrical box.
Installation (next to an electrical box)
- Break off the tabs on the device using pliers, as shown in Diagram B.
- Mark the location of the device on the wall surface to the left or right of existing device(s) installed in the electrical box, visually aligning it with existing device(s).
- Install and secure the device:
- Fold the wires into the electrical box, taking care not to pinch a wire.
- Use double-sided stickers to install on a tiled or any other smooth surface next to the electrical box.
- Use provided mounting screws if the surface next to the electrical box is drywall or an uneven surface where the sticker may not work.
- Install the multi-gang subframe using sub-frame screws provided with the radiant wall plate.
- Snap on the radiant wall plate.
- If installing with a non-radiant wall plate, skip steps 3d and 3e above and use screws provided with the other wall plate to secure this device.
Setup
This device is designed to work with an approved Zigbee Hub. Please see the onboarding instructions for the Zigbee Hub before removing the battery tab.
Remove battery insulation tab as shown in the image (see Diagram B).
Diagram Description (Diagram B): Illustrates breaking off tabs on the device using pliers for multi-gang installations, and removing the battery insulation tab.
Getting to Know Your Battery Powered Device
| Item | Name | Description |
|---|---|---|
| 1 | LED Indicator Light | Indicates the current state of device during setup. |
| 2 | EZ Button | Used to reset device. |
Replace Battery (Diagram D)
Replace battery upon receiving a low battery alert in the Home + Control app. Average battery life is 8 years. To replace, remove the switch cover and slide the battery out. Replace with a CR2032 3V battery.
More Information
For the most up-to-date information on this product, please visit the website at: https://www.legrand.us/markets/hospitality/smart-hospitality
Limited One Year Warranty
Legrand will remedy any defect in workmanship or material in Legrand products which may develop under proper and normal use within one year from the date of purchase by a consumer. This remedy is in lieu of any and all expressed or implied warranties of merchantability or fitness for a particular purpose. Such remedy by Legrand does not include or cover the cost of labor for removal or reinstallation of the product. All other further elements of damage (incidental or consequential damages) for breach of any and all expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose, are excluded hereby. Any implied warranties, including where required warranties of merchantability or fitness for a particular purpose, shall be limited to the one-year period set forth above. For safety, all repairs to Legrand products must be made by Legrand, or under its specific direction. To obtain warranty performance, contact Legrand, Syracuse, New York 13221, for instructions concerning return or repair, and return the product postage paid with your name, address, a written description of the installation or use, and the observed defects or failure to operate. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Questions? We're here to help.
Phone: 1-877-833-3303 (8:00 a.m. to 8:00 p.m. EST, M-F)
Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart-lighting.aspx (Click on the chat icon to open a dialogue box)
Patents | Legrand
