Inspire
It's your home. Live Beautiful!
SIGNY 202-144
Assembly Instructions
Congratulations on your purchase – Get ready to be inspired!
Please check to ensure that all parts are included. Contact the place of purchase for any service issues. Keep this document for reference in case parts are needed.
* THIS ITEM IS NOT RECOMMENDED FOR COMMERCIAL USE *
IMPORTANT: MUST READ BEFORE ASSEMBLY!
For your furniture to last, correct assembly and proper maintenance are necessary. Please follow the information provided below to fully enjoy your furniture.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE.
Basic Assembly Techniques
Step 1: Screw Assembly
Before attaching each of the screws, make sure that the smaller lock washer is between the larger washer and the head of the screw.
[Diagram: Close-up of screw assembly showing a lock washer between a larger washer and the screw head.]
Step 2: Hand Tighten
Position each part correctly and insert all screws into their respective holes. Then, hand-tighten only until 70% tight. Complete tightening with the tools will come at a later step.
[Diagram: Hand tightening screws into pre-drilled holes, showing a 70% tight indication.]
Step 3: Level Surface
Make sure the furniture rests on a flat and level surface with each leg evenly touching the ground. Use a soft blanket or carpet underneath when turning the piece on its side.
[Diagram: Furniture resting on a flat surface, with a blanket underneath for protection.]
Step 4: Height Adjustment
Some furniture come with optional height adjustment knobs underneath each leg. Turn this knob counterclockwise ⬆️ to raise the leg level or clockwise ⬇️ to lower the leg level.
[Diagram: Close-up of a furniture leg with a height adjustment knob. Arrows show turning counterclockwise to raise and clockwise to lower.]
Step 5: Final Tightening
Finally, make sure all parts are properly aligned then use the included tools to completely tighten the screws. Your furniture is now ready for use.
[Diagram: Furniture parts aligned, with tools tightening screws.]
Step 6: Maintenance
Store the tools ? for later maintenance. Tighten the screws again after two (2) weeks, and then at least once every six (6) months after that.
[Diagram: A toolbox icon.]
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE. THE SCREWS MAY LOOSEN OVER TIME AND CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS CAN LEAD TO COLLAPSE AND CAN CAUSE SERIOUS INJURY.
Parts and Hardware
Refer to the diagrams for visual identification.
- Part A: Chair Seat/Back
- Part B: Frame (x2)
- Part C: Base Plate
Hardware:
- a: M6x12mm screws (x4)
- b: M6x25mm screws (x2)
- c: M6x18mm screws (x2)
- d: M6x30mm screw (x1)
- e: Washers/Spacers (x8)
- f: Allen Wrench (x2)
[Diagram: Visual representation of parts A, B, C and hardware a-f with labels and quantities.]
Assembly Steps
Before starting: Turn the chair top upside down on a soft working surface.
Step 1
Attach the two 'B' frame pieces together using one 'd' screw and one 'f' Allen wrench. Ensure alignment before tightening.
[Diagram: Two 'B' frame pieces being joined by screw 'd' and Allen wrench 'f'.]
Step 2
Attach the 'C' base plate to the assembled 'B' frame pieces. Use four 'a' screws, eight 'e' washers/spacers, and two 'f' Allen wrenches. The diagram shows the 'C' plate fitting onto the frame, with screws passing through the plate and into the frame, secured by washers.
[Diagram: 'C' base plate being attached to the 'B' frame pieces using screws 'a', washers 'e', and Allen wrench 'f'. A magnified view shows the connection detail.]
Step 3
Attach the 'A' chair seat/back to the 'C' base plate assembly. Use two 'b' screws, two 'e' washers/spacers, and two 'f' Allen wrenches. Also, use two 'c' screws. Ensure all parts are securely fastened.
[Diagram: 'A' chair seat/back being attached to the 'C' base plate assembly using screws 'b', 'e', 'c', and Allen wrench 'f'.]
