Avenli Super Clean Filter Pump User Manual

Introduction

Thank you for purchasing the Avenli Super Clean Filter Pump. This manual provides comprehensive instructions for installation, operation, general maintenance, cleaning, replacement, and troubleshooting. It is designed to ensure the safe and efficient use of your filter pump system.

The Avenli filter pump system is manufactured to high-quality standards and is designed for above-ground swimming pools. It offers superior filtration, high volume flow, easy installation, low maintenance costs, and quiet operation. The unit is constructed with reliable, corrosion-proof materials and features an elegant design. It is also compact for easy storage during winter and is UL & GS certified, ensuring safety for swimming and the environment.

Please read all instructions carefully before installing and operating the filter pump. It is important to share this information with anyone who will be using the pool.

Safety Instructions

WARNING: Always follow these important safety precautions when installing and using this electric equipment:

• Check all clamps and system accessories before operating the pump.
• Do not bury the supply cord of the adapter. Locate it where it will not be damaged by lawn mowers, hedge trimmers, or other equipment.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless supervised or instructed by a responsible person. Children should be supervised to ensure they do not play with the appliance.
• Do not use this filter pump to vacuum the pool. It is designed only for storable pools, not for permanently installed pools.
• The power cord of the adapter and the pump's input wire cannot be replaced. If damaged, the adapter or pump should be scrapped.
• Do not place the 230V adapter near the pool. The transformer and socket outlet should be more than 3.5 meters away from the pool. The pump and adapter must not be installed in areas prone to flooding.
• Ensure outdoor sockets are protected by a residual current device (RCD) with a rated residual operating current not exceeding 30 mA.
• Do not drop the filter pump or adapter into water.
• Before starting the filter pump, fix the filter base with screws on a solid surface.
• Avoid overheating the filter pump motor. Ensure the pump is always running with water and never left dry. Improper use can cause overheating, motor burnout, and damage.
• Excess air in the pump can cause it to race and damage the filter pump. Gently turn the air release valve (P1) to drive out all air from the hose and filter housing.
• This appliance can only be used by children aged 8 years and above, or persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, if they have been given supervision or instruction concerning safe use and understand the hazards involved. Children should not play with the appliance. Cleaning or user maintenance should not be performed by children without supervision.
• The supply cord cannot be replaced if damaged; the appliance should be scrapped.
• The pump must not be used when people are in the water.
• The pump must be supplied through an RCD with a rated residual operating current not exceeding 30mA.
• The maximum total head is 0.9 meters (for pumps with a rated power input exceeding 50W).
• The appliance should be installed at least 2m from the pool, and the plug located 3.5m from the pool (for France market).
• The pump must be fixed on the ground or a pedestal with two $5 bolts or screws to prevent accidental falling.

Parts Listing & Illustration

Refer to the diagrams on pages 6 and 7 for part identification.

Illustration of Installation:

[Diagram showing water level, inlet, outlet, and various components labeled P1 through P14, with arrows indicating water direction and connections. The illustration is not to scale.]

Installation Instructions

1. Before installing the filter pump, set up the pool and fill it with water according to the pool's installation instructions. Operate the filter pump only when the water level has reached the maximum in the pool. Low water pressure may cause noisy motor operation.
2. Remove the filter pump and hoses from the packaging.
3. Place the filter pump below pool water level, at least 0.2m and no more than 1.0m deep.
4. Mount the filter pump on a solid and even ground using the mounting holes in the pump base and screws.
5. Insert the Filter Cartridge (P6) into the Filter Chamber (P7), ensuring it is seated correctly.
6. Place the Filter Housing O-Ring (P5) on the Filter Chamber (P7).
7. Place the Filter Housing Cover (P3) on the Filter Chamber (P7).
8. Finger tighten the Filter Chamber Cover Retainer (P3) clockwise.
9. Connect one Filter Hose (P12) to the inlet port of the Filter Pump (top) and the lower hose connection of the pool. Secure with hose clamps (P11).
10. Gently turn the air release valve (P1) counter-clockwise 1-2 turns to release air.
11. Connect the second Filter Hose (P12) to the upper hose connection of the pool and the outlet port (bottom) of the Filter Pump. Secure with hose clamps.
12. The sound pressure level is less than 82 dB (A).

Operating Instructions

1. Ensure the pool is filled with water and place the Filter Pump in a suitable position.
2. As water flows into the filter pump, the water pressure will push air out through the air release valve (P1).
3. Gently finger tighten the air release valve (P1) clockwise.
4. Connect the power supply cord of the adapter to a 230V AC outlet to operate the Filter Pump until the water in the pool is clear.

General Maintenance

• Disconnect power to the motor before working on the pump or motor.
• It is recommended to have spare parts available, such as two filter cartridges.
• No lubrication or regular mechanical maintenance is required.
• Wash the outside of the filter with a mild detergent and water, then rinse with a hose.
• Do not use solvents to clean the filter, as they may damage plastic components.
• Maintain pool pH level between 7.0 and 7.4.
• The adapter voltage is AC 230V.
• Do not place the filter pump in tall grass, as this can cause the motor to overheat.
• When the pool water is completely emptied, remove all pool hoses from the pool and the filter pump.
• Exhaust water from all housings of the filter pump.
• Store all filter pieces in a dry, ventilated location. Ensure all parts are dry before storage.
• The filter pump can be stored in a dry location, using the original packaging for storage for the next season.

Cleaning and Replacement

1. Ensure the 230V adapter's power supply cord is disconnected from the electric outlet.
2. Remove the Filter Chamber Cover Retainer (P3) by turning it counter-clockwise. Place it in a safe location.
3. Clean the used Filter Cartridge (P6) or replace it if necessary.
4. Check the inside of the Filter Chamber (P7).
5. If dirt or sediment is found on the bottom of the housing, flush it out with water using a bucket or garden hose.
6. Return the Filter Chamber Cover Retainer (P3) to its position and fasten it clockwise onto the filter housing.
7. Reconnect the power supply cord of the adapter.

Trouble Shooting Guide

PUMP DOES NOT OPERATE:

• Check for blown fuses, circuit breakers, or disconnected electrical wiring.
• Check the motor. If it is too hot or overloaded, shut it off and let it cool down. Consult an expert if the problem persists.

MOTOR RUNS, BUT DOES NOT PUMP WATER OR WATERFLOW IS TOO SLOW:

• Check for obstructions in the intake or discharge hose, or inside the pool wall.
• Tighten hose clamps, check hoses for damage, and check the pool water level.
• Clean the filter cartridge more often. It is reusable and easy to clean with a garden hose.
• Replace the filter cartridge if necessary.
• Consult an expert.

PUMP LOSES PRIME:

• Ensure the water level in the pool is at least 5 cm above the bottom of the skimmer throat when the system is not operating.
• Make sure there are no leaks in the suction piping.
• Check if the filter cartridge is dirty and needs cleaning. It is reusable and easy to clean with a garden hose.
• Consult an expert.

FILTER DOES NOT CLEAN POOL:

• Adjust chlorine and pH levels.
• Clean or replace the filter cartridge. It is reusable and easy to clean with a garden hose.
• Check the cartridge for holes. Replace if damaged.
• Allow the pump to operate longer.
• Clean away debris from the strainer screen at the pool wall.
• Consult an expert.

Limited Warranty

ATTENTION CUSTOMER: Please read this statement carefully and keep your original store receipt with this warranty certificate. Your receipt is required as proof of purchase and to verify the length of your pool ownership.

Avenli warrants all components in this filter pump against defects in materials and workmanship under normal use and service for a period of 365 days from the date of purchase for the original owner only. If any components have been replaced by the consumer, damaged, or misused, the corresponding warranty on those components is invalidated. In such situations, you will be advised of the cost of replacement parts and processing instructions. Please register your warranty within 30 days of purchase on www.jilong.com to validate your warranty.

If a verifiable manufacturing defect is found during the relevant time period, Avenli agrees to repair or replace, at its option, any pumps under warranty, provided proper proof of purchase is presented.

This limited warranty is not valid if the pool is used for commercial purposes, or if damage is caused by an accident, act of God, consumer misuse, neglect or abuse, vandalism, improper use of chemicals, exposure to extreme weather conditions, or negligence during pool setup or disassembly.

Avenli cannot be held responsible for installation costs (including water), labor, or transportation expenses incurred due to the replacement of defective parts. This limited warranty also does not cover any unauthorized alterations to the pool system.

Manufacturer Information:

SHANGHAI JILONG SPORT AND LEISURE PRODUCTS CO., LTD
2555 XiuPu Road, Pudong Area, Shanghai, China.
www.JLeisure-Global.com

JIANGSU JILONG SPORT AND LEISURE PRODUCTS CO., LTD
NO.1 Industrial Area South Zhongchen Road Zhongyang Town, Suqian, Jiangsu, China

Correct Disposal of this product

This marking indicates that the product should not be disposed of with other household waste throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.