Emerson SmartSet Clock Radio

Introduction

Thank you for purchasing this Emerson SmartSet® Clock Radio. This clock radio utilizes Emerson's patented SmartSet® Automatic Time Setting System. Upon connecting to the AC outlet, the clock automatically sets the correct Year, Month, Date, Day, and Time, including Daylight Saving Time adjustments. It features dual alarms, PLL FM radio, and a backup lithium battery to maintain settings during power interruptions.

This manual covers features for models ER100103 and CKS1900. Some features may be specific to one model.

Important Safety Instructions

WARNING: To prevent fire or shock hazard, do not expose this appliance to rain or moisture. Do not use with extension cords unless blades can be fully inserted.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• Read and keep all instructions.
• Clean only with a dry cloth.
• Do not block ventilation openings.
• Avoid heat sources, direct sunlight, and excessive moisture.
• Protect the power cord from damage.
• Use only manufacturer-specified attachments.
• Unplug during lightning storms or long periods of non-use.
• Refer servicing to qualified personnel.
• Do not expose batteries to excessive heat.

Battery Warning: Do not ingest coin/button cell battery. If swallowed, it can cause severe internal burns in 2 hours and lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. Seek immediate medical attention if batteries are suspected to have been swallowed or placed inside any part of the body.

French Warning: AVERTISSEMENT: AFIN DE PRÉVENIR TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION N'EXPOSEZ PAS CET APPAREIL À LA PLUIE NI À L'HUMIDITÉ.

Location of Controls and Indicators

Controls and indicators vary slightly between models. Refer to the diagrams in the original manual for precise placement.

Common Controls:

• Display: Shows time, date, alarm status, etc.
• UNIT ON/OFF (Standby) Button: Powers the unit on/off.
• SNOOZE / DIMMER Button: Snoozes active alarms or adjusts display brightness.
• SLEEP Button: Sets a timer to automatically turn off the radio.
• TUNE +/- / SET +/- Buttons: Used for tuning radio stations and setting time/alarms.
• VOLUME +/- Buttons: Adjusts audio volume.
• ALARM 1 / ALARM 2 Buttons: Used to set and activate alarms.
• ALARM 1 / ALARM 2 Indicators: Show if Alarm 1 or Alarm 2 is active.
• AM Indicator: Displays 'AM' when the time is in the morning.
• LOW BATT Indicator: Alerts when the backup lithium battery is low.
• AUX IN Jack: Connects external audio devices via a 3.5mm cable.
• Speaker: Provides audio output.
• AC Adapter: Provides power and acts as the FM antenna.

Model ER100103 Specific Controls:

• TIME ZONE / AL MODE Button: Sets the time zone and alarm operating modes (Everyday, Weekdays, Weekends).
• STORE MEM. Button: Stores favorite radio stations.
• Projection Clock ON/OFF Button: Activates the red clock projection onto a ceiling or wall.
• ROTATE IMAGE Button: Adjusts the orientation of the projected clock image.
• USB Charge Out: Provides 5V/1.2A output for charging mobile devices.

Model CKS1900 Specific Controls:

• TIME Setting / BAND Select Button: Sets the time and selects AM/FM radio bands.
• TIME ZONE / MEMORY Button: Sets the time zone and recalls stored radio presets.
• WEEK/ALARM MODE Button: Selects alarm operating modes (Everyday, Weekdays, Weekends).

Preparation for Use

Unpacking and Setup

Remove the unit from its packaging. Save packing materials for potential future service. Place the clock radio on a level surface away from direct sunlight, heat sources, dust, moisture, and vibration. Ensure adequate ventilation (at least 10 cm around the unit).

The AC adapter cord serves as the FM antenna; extend it fully for best reception.

SmartSet® Automatic Time Setting

Upon first connection to AC power, the internal computer automatically sets the time and date. The default time zone is Eastern Time (ZONE 2). If you are in a different time zone, press and hold the TIME ZONE button (ER100103) or TIME ZONE / MEMORY button (CKS1900) and use the TUNE +/- or SET +/- buttons to select your correct zone (ZONE 1-7).

The system automatically adjusts for Daylight Saving Time and Leap Years.

Viewing Date and Year:

Press the MONTH/DATE button to view the current month and date (MM.DD). Press the MONTH/DATE and TIME buttons together to view the year (YYYY).

Manual Time Adjustments:

To manually adjust the time, press and hold the TIME button (ER100103) or TIME Setting button (CKS1900), then use the SET +/- buttons to advance or decrease the hour and minute. The SmartSet® system will retain your manual setting.

Setting Alarms

The clock radio features dual alarms (AL1, AL2) that can be set independently.

Setting Wake-Up Time:

Press and hold the desired alarm button (ALARM 1 or ALARM 2). Use the SET +/- buttons to adjust the wake-up hour and minute. Ensure the AM/PM indicator is correct. Release the buttons when the desired time is displayed.

Setting Alarm Volume:

After setting the wake-up time, press the alarm button again. Use the VOLUME +/- buttons to set the alarm volume (e.g., U03-U15). Press the alarm button again or wait for the display to return to time mode to confirm.

Selecting Alarm Mode:

Choose between Everyday (1-7), Weekdays only (1-5), or Weekends only (6-7). Press and hold the alarm button, then press the AL MODE (ER100103) or WEEK/ALARM MODE (CKS1900) button until the desired mode is shown on the display.

Wake to Radio or Buzzer:

Set alarms to wake you with the radio or a buzzer. Alarm 1 typically uses a single beep, and Alarm 2 uses a double beep.

Snooze Alarm:

When an alarm sounds, press the SNOOZE/DIMMER button to temporarily silence it. The alarm will sound again after approximately 9 minutes. This can be repeated, but the alarm will stop after one hour of snoozing.

Listening to the Radio

Press the RADIO ON/OFF button to turn the radio on. Use the BAND button (CKS1900) or tune directly (ER100103) to select AM or FM. Adjust volume with VOLUME +/-. Tune to stations using the TUNE +/- buttons. Press and hold TUNE +/- for auto-station seeking.

Storing and Recalling Stations:

Tune to a desired station. Press the STORE button (ER100103) or MEMORY button (CKS1900). Use TUNE +/- to select a memory location (e.g., P01-P20 for ER100103, P01-P10 for CKS1900). Press STORE or MEMORY again to save. To recall, press MEMORY and cycle through locations using TUNE +/-.

Antenna Information:

AM reception uses an internal bar antenna. FM reception uses the AC adapter cord; extend and position it for best signal.

Audio Sources

AUX IN Jack:

Connect an external audio source (like a phone or MP3 player) using a 3.5mm stereo AUX cable to the AUX IN Jack. The AUX indicator will light up. Volume is controlled by the connected device.

Model ER100103 Specific Features

Red Projection Clock:

Tilt the projector towards a surface. Press the Projection Clock ON/OFF button to display the time. Rotate the focus knob for clarity. Use the ROTATE IMAGE button if the image is inverted. The projector activates with the alarm and turns off when the alarm is silenced.

USB Charging:

The unit provides a USB Charge Out port (DC 5V, 1.2A) for charging compatible mobile phones or digital audio players. Charging current may vary based on the USB cable and device.

Timers and Controls

Sleeping to Music Timer:

Press the SLEEP button to set a timer (10-90 minutes) for the radio to shut off automatically. Press SLEEP repeatedly to cycle through times or hold with SET +/- to adjust. Press the SNOOZE/SLEEP OFF button to cancel the timer.

4-Level Dimmer Control:

Press the SNOOZE/DIMMER button while in standby mode or when the radio/AUX is on to select one of four brightness levels for the display.

Maintenance and Battery Replacement

Care of Cabinets:

Clean cabinets with a soft, dry cloth. For smudges, use a slightly damp cloth. Avoid abrasive cleaners or liquids inside the unit.

Lithium Battery Replacement:

The unit has a backup lithium battery (CR2032 or equivalent) to maintain memory during power outages. The LOW BATT indicator will flash when replacement is needed. To replace:

1. Disconnect AC power (though the manual implies it should remain connected for memory). Keep AC connected to maintain memory during replacement.
2. Use a small screwdriver to remove the screw securing the battery holder.
3. Remove the old battery and insert the new one, observing correct polarity (+).
4. Slide the holder back and replace the screw.

WARNING: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

Resetting the Clock After Memory Loss

If the backup battery is exhausted and AC power is interrupted, the clock may reset to its default (e.g., 12:00 AM, Sunday, January 1st, 2017). If the time and date display appears incorrect (e.g., Jan 1st), replace the lithium battery and then reset the time, date, and year manually using the TIME, MONTH/DATE, and SET +/- buttons. Remember to also reset alarm and sleep timer settings.

Limited Warranty

Emerson Radio Corp. warrants this product against manufacturing defects for ninety (90) days from the original purchase date in the United States. Service requires contacting Emerson Customer Service (1-800-898-9020) for authorization. The warranty covers repair or replacement of defective parts and labor. It does not cover damage from misuse, accidents, or unauthorized modifications. Shipping costs to and from the repair facility are the customer's responsibility. This warranty is non-transferable and applies only to the original purchaser.

Product Identification

Model Number: ER100103 / CKS1900

Serial Number: Located on the back/bottom cabinet. Record for future reference.

For additional assistance, visit www.emersonradio.com or contact customer service.