W1 Plus User Manual

1. Outer Case Description

The W1 Plus is a versatile remote control. It features a primary side with navigation buttons including a power button [Power Button], home button [Home Button], directional pad (Up [Up Arrow], Down [Down Arrow], Left [Left Arrow], Right [Right Arrow]), an OK button [OK Button], a back button [Back Button], a menu button [Menu Button], a voice control button [Microphone Button], volume controls [Volume Down Button], [Volume Up Button], and dedicated buttons for YouTube [YouTube] and Netflix [Netflix]. The reverse side features a full QWERTY keyboard for text input.

2. Key Function Definition and Key Codes

This section details the functions and corresponding codes for the primary buttons:

3. QWERTY Keyboard Layout and Key Codes

The reverse side of the remote features a QWERTY keyboard. The following table details the default and Fn combination key codes:

Remark: Pressing the "Fn" key switches between default and combined key codes. The "Fn" indicator light shows the state of the combination key (on for combination, off for default).

3. Pairing

How to pair:

1. Insert the Nano receiver into the USB port of your Android TV Box or Smart TV.
2. Move the remote control close to the receiver (within 3cm).
3. Press and hold the [Volume +] and [Volume -] buttons on the remote for 3 seconds.
4. The slow flashing indicator light will become steady, indicating pairing mode. Release the buttons.
5. If pairing is successful, the indicator light will flash 3 times. If unsuccessful, it will flash after 30 seconds.

4. Voice Function

The remote supports the Google ATV protocol. Pressing the [Microphone Button] activates the voice assistant on compatible devices (Smart Projectors, Smart TVs, Android TV Boxes). The indicator light will turn on during voice input. Releasing the button stops the voice function.

5. Air Mouse Function

How to turn ON/OFF Air-mouse function:

• Press the [Air mouse button] to toggle the air mouse function.
• When the QWERTY keyboard is facing up, the air mouse function automatically stops.

6. CPI Adjustment (Pointer Speed Adjustment)

How to adjust cursor speed:

• Speed up: Press and hold [OK Button] and [Volume + Button] for about 3 seconds until the indicator light blinks. This increases the CPI by one level.
• Slow down: Press and hold [OK Button] and [Volume - Button] for about 3 seconds until the indicator light blinks. This decreases the CPI by one level.

7. Back-light Function

The back-light for both sides of the remote is supported. The back-light automatically turns off on one side when the other side is active (e.g., QWERTY keyboard up turns off the main button side back-light, and vice versa). The back-light enters standby mode after 5 seconds of inactivity.

8. Key Anti-Loss Function

If any button is held down for more than 2 minutes, the remote will stop responding and enter standby mode.

9. IR Learning Function

How to use IR learning:

1. On the W1 Plus remote, press and hold the [OK Button] and [Air-Mouse Button] simultaneously to activate IR learning. The indicator light will brighten after 3 seconds.
2. When a learned button on W1 Plus is pressed, the indicator light will blink slowly.
3. Maintain a distance of 1-5cm between the W1 Plus remote and the infrared remote you wish to learn from. Press any button on the infrared remote, then press the corresponding button on the W1 Plus.
4. After successful learning, the indicator light will blink 3 times and remain steady. Repeat steps 2-3 to learn other buttons.
5. Press the [Air-mouse button] to exit learning mode and save the data.

Note: If the remote is not connected via the Nano receiver (in IR learning stage), it operates using infrared key values. When connected via Nano receiver, it uses HID key codes. The [Power Button] always emits infrared key codes. The [Voice Button] and [Air-mouse Button] do not emit infrared key codes.

10. Back-light Function (Details)

Both sides of the remote feature backlighting. To disable it, use the dedicated button on the QWERTY keyboard side. The back-light automatically turns off on the inactive side. It also enters standby after 5 seconds of no operation.

11. Anti-Loss Function

To locate the remote, press the "Search" button on the Nano receiver. The remote will emit a sound. Press any button on the remote to stop the sound.

12. Low Battery Reminder

If the remote's battery is low, the indicator will blink quickly 5 times during use.

13. Standby Mode

The remote enters standby mode after 15 seconds of inactivity. Press any button to wake it up.

14. Main Function Description Summary

1. Air-mouse Function: Press the pointer button to activate/deactivate.
2. Pairing Function: During pairing, the slow blinking indicator becomes steady. Successful pairing results in 3 fast blinks.
3. Voice Assistant Function: Press and hold the voice button to speak; release to stop.
4. Low Battery Reminder: A quick 5-time blink indicates low battery.
5. Anti-loss Function: Press "Search" on the Nano receiver to find the remote via sound. Press any remote button to silence it.
6. Sleeping Mode: The remote enters sleep mode after inactivity. Press any button to reactivate.