The Puffco Proxy

What's Inside

An exploded view diagram shows the components of the Puffco Proxy:

• A: Carry Case
• B: Chamber*
• C: Base
• D: Glass**
• E: Cable
• F: Dual Tools
• G: Loading Tool

*Part (B) requires periodic replacement. **Each glass piece is hand blown and may vary slightly in size.

Features

• Modularity ?
• Portability ?
• Easy to clean ✨
• USB-C ?

Quick Start

1. Fully charge device before first use.
2. To unlock/lock the device, hold down button for three seconds. [HOLD]
3. Single click to toggle through settings. BLUE (Low), GREEN (Medium), RED (High), WHITE (Peak). [1X]
4. Use Hot Knife or Dual Tool to place contents inside of the bowl.
5. Place carb cap on top of the chamber and press down until snug.
6. Double click to initiate heat up. Press and hold button anytime to stop. Pulsing light indicates device is heating up. [2X]
7. Device will vibrate and lights will flash three times when ready. Inhale gently for best results. (See p. 8 for info on Boost Mode)
8. Use dry Dual Tool to clean the chamber after each use. Wipe gently in a circular motion.

⚠️ Do not initiate heat up more than four (4) times consecutively.

Hold the device upright/vertical during use.

Cleaning

Chamber

1. Unscrew the chamber from the base. ⚠️ Do not handle if hot.
2. Light Cleaning: Use a cotton swab to gently remove any residue with 90%+ isopropyl alcohol.
3. Deep Cleaning: Submerge the chamber in 90%+ isopropyl alcohol for 20 minutes. Never use water (isopropyl alcohol only). ⚠️ Isopropyl alcohol is highly flammable. Let it dry completely before heating device. ⚠️ Do not clean with Isopropyl alcohol while the chamber is hot.

Base

Preparation: Remove glass and chamber.

Gently clean the gold contact points using cotton swabs soaked in isopropyl alcohol.

Clean the airpath between the base with a cotton swab soaked in isopropyl alcohol. ⚠️ Do not allow water into the base at any time.

Glass

Preparation: Carefully remove glass from base.

1. Once removed, submerge in isopropyl alcohol.
2. After soaking, remove from isopropyl alcohol and rinse clean with water. (Make sure it's rinsed thoroughly prior to use.)
3. Allow glass to thoroughly dry before reattaching to base.

⚠️ Be sure to clean your Proxy using only 90%+ Isopropyl Alcohol.

Triple Clicking

Triple clicking can show the battery percentage:

• Green: High
• Orange: Medium
• Red: Low

Advanced Features

Boost Mode

After heatup, double click to activate boost mode. This extends the time and increases the temperature of your hit. You can continue to boost as needed. ⚠️ Do not initiate heat up more than four (4) times consecutively.

Error Codes

• 1: No chamber (3 white flashes)
• 2: Chamber error (red white red white)
• 3: Device overheating (red for 5 seconds)
• 4: Low battery (3 red flashes)

General Warnings

• Do not overfill the chamber.
• Do not blow or exhale hard into the glass.
• Strong inhales may cause spillage and damage to your chamber.
• Do not charge or operate below 32° F or above 100° F.
• Use only with the provided cable.
• Keep away from moisture and high humidity.
• Store in a cool dark place when not in use.
• During use the chamber is hot (burn hazard).

*Not for use with tobacco, nicotine containing e-liquids, or any synthetic nicotine or nicotine substitute.

Need Help? Contact Us!

Keep your proof of purchase.

If you're having anything less than a perfect experience, reach out to our support team.

Visit Puffco.com/Support for FAQ's, how-to videos, and other resources that may solve your problem quickly.

Visit Puffco.com to learn more.

Share the View

Use #PUFFCOPROXY to share your experience. Kindly follow us on Instagram!

Puffco