IOGEAR GXRMSW02 PP4.0 Secure KVM Remote Port Selector V2
Quick Start Guide
Package Contents
- 1 x GXRMSW02
- 1 x Quick Start Guide
- 1 x Warranty Card
System Requirements
The following IOGEAR PP4.0 Secure KVM models are compatible:
- GCS1212TAA4, GCS1214TAA4, GCS1218TAA4, GCS1222TAA4, GCS1224TAA4, GCS1228TAA4,
- GCS1312TAA4, GCS1314TAA4, GCS1322TAA4, GCS1324TAA4,
- GCS1412TAA4, GCS1414TAA4, GCS1418TAA4, GCS1422TAA4, GCS1424TAA4, GCS1428TAA4,
- GCS1212TAA4C, GCS1214TAA4C, GCS1218TAA4C, GCS1222TAA4C, GCS1224TAA4C, GCS1228TAA4C,
- GCS1312TAA4C, GCS1314TAA4C, GCS1322TAA4C, GCS1324TAA4C,
- GCS1412TAA4C, GCS1414TAA4C, GCS1418TAA4C, GCS1422TAA4C, GCS1424TAA4C, GCS1428TAA4C,
- GCS1512TAA4, GCS1514TAA4, GCS1522TAA4, GCS1524TAA4,
- GCS1512TAA4C, GCS1514TAA4C, GCS1522TAA4C, GCS1524TAA4C
Overview
- A. Port Selection Pushbuttons
- B. Port LEDs
- C. Num Lock LED
- D. Caps Lock LED
- E. Scroll Lock LED
- F. CAC LED
- G. Port Name Label Area
Device Front Panel Description
The front panel of the IOGEAR PP4.0 Secure KVM Remote Port Selector V2 features:
- Eight numbered pushbuttons (1-8) labeled 'A', each with an associated LED indicator labeled 'B'.
- Status LEDs above the pushbuttons: Num Lock (C), Caps Lock (D), Scroll Lock (E), and CAC (F).
- A large area labeled 'G' at the bottom for port name labels.
Hardware Installation
Connect the GXRMSW02 to the IOGEAR PP4.0 Secure KVM RPS port.
Notes:
- Connect the GXRMSW02 before powering on the IOGEAR PP4.0 Secure KVM.
- Connecting the GXRMSW02 after the KVM is powered on will prevent detection.
- When connected to a 2-Port Secure KVM Switch, only pushbuttons 1 and 2 are detected and functional.
- When connected to a 4-Port Secure KVM Switch, only pushbuttons 1, 2, 3, and 4 are detected and functional.
- When connected to an 8-Port Secure KVM Switch, all eight pushbuttons are detected and functional.
Device Rear Connections Description
The rear of a compatible KVM switch shows connections for:
- Multiple "CPU" ports (1-8), each with a "B" connector.
- "CONSOLE A" and "CONSOLE B" ports, each with an "A" connector.
- A "CAC" port.
Limited Warranty
This product is covered by a 3-year limited or lifetime warranty. For full terms and conditions, visit IOGEAR Warranty Information.
Register your product online at IOGEAR Registration.
Contact Support
For assistance setting up this product, please visit:
EMC Information
Federal Communications Commission (FCC) Statement:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Operating this equipment in a residential area may cause radio interference, which the user must correct at their own expense.
CE Statement:
This device complies with European Union directives: Electromagnetic Capability (2014/30/EU) and Low Voltage (2006/95/EC).
Warnings
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Residential Environment Warning: Operation of this equipment in a residential environment could cause radio interference.
California Proposition 65 Warning: This product may expose you to chemicals, including Cadmium, known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit P65Warnings.ca.gov.
Mechanical Intrusion Warning: If a mechanical intrusion is detected by the RPS (when connected to the switch and aligned), this will permanently disable both the RPS and the switch. All LEDs (on RPS and front panel, except the Power LED on the switch) will flash continuously.
