CHESONA Wireless Keyboard for iPad Pro 12.9-inch

Product Overview

This document provides instructions for the CHESONA Wireless Keyboard for iPad Pro 12.9-inch (5th/4th/3rd Generation). It covers operation, connection, charging, specifications, and troubleshooting.

Packing Included:

• 1 x Detachable wireless keyboard case for iPad Pro 12.9 5th/4th/3rd Gen
• 1 x USB charging cable (No Charger)
• 1 x User manual

Operation Instruction

Powering On/Off: Slide the key to "ON" to turn on the keyboard power.

Bluetooth Pairing:

1. Open Bluetooth settings on your iPad.
2. Press the 'FN' and 'C' keys together on the keyboard. The BT indicator light will flash.
3. Search for "Bluetooth 3.0 Keyboard" on your iPad and select it to connect.
4. Once connected, the BT indicator light will stop flashing.

Note: The keyboard will automatically enter power-saving mode after 10 minutes of inactivity. Press any key and wait 2-3 seconds to wake it up.

Backlight Control

Use the 'Switch Backlight' function to control the backlight. Cycle through colors and brightness levels.

Available Colors: Blue, Green, Red, Cyan, Purple, Yellow, White.

Specifications

Second Connection

1. To reconnect after the keyboard has entered power-saving mode, simply press any key and wait 2-3 seconds. Do not press 'Fn+C' again, as this may cause a failed connection.
2. If you are unable to connect for the second time:
• On your iPad, go to Bluetooth settings, select "BT 3.0 Keyboard", and choose "Forget this device".
• Turn off your iPad and the keyboard, then restart both devices.
• Follow the initial pairing steps to connect again.
3. For further assistance or unresolved issues, please contact CHESONA customer support at chesonaus@163.com.

Indicator Lights

• Capital Indicator Light: Illuminates when Caps Lock is active.
• Wireless Connect Indicator: Flashes slowly when entering BT pairing mode. Turns off upon successful pairing.
• Charging Indicator Light: Solid red light indicates low battery. Solid light during charging. Turns off when charging is complete.
• Electric Indicator Light: Illuminates for 2-3 seconds upon powering on the keyboard.

Charging

Fully charge the keyboard before first use or after extended periods of inactivity (at least 2 hours).

To charge:

1. Use the provided micro-USB cable or your own.
2. Connect the small end of the micro-USB cable to the keyboard and the other end to a USB port.

Important: If the power indicator flashes continuously, it signifies a battery level below 20%. Charge the keyboard promptly to prevent issues.

Installation and Removal

To remove the keyboard case from the iPad:

1. Hold the iPad firmly on both sides.
2. Gently push off the back cover with your thumbs. The cover is secured by two tabs.
3. Carefully "peel" the cover away from the iPad.
4. Lift the iPad out of the case.

Visual Aids: (Refer to numbered images in the original manual for visual guidance on removal steps.)

Troubleshooting

If the keyboard is not functioning correctly, please verify the following:

1. Ensure the BT function is enabled on your iPad (or other connected BT device).
2. Confirm the BT keyboard is within the 33 feet (approx. 10 meters) connection range.
3. Check that the BT keyboard is adequately charged.

If specific keys or commands are unresponsive, work sporadically, or exhibit lag:

• Restart your iPad (power off and then power on). This resolves most common issues.

If the problem persists, follow these steps:

1. On your iPad, delete all previously paired Bluetooth devices.
2. Turn off the Bluetooth function on your iPad.
3. Reboot your iPad.
4. Turn on the Bluetooth function on your iPad.
5. Switch the keyboard off and then on again.
6. Repeat the connection steps outlined on pages 1 and 2 of this manual.