Split Inground Light Installation Instructions

Product Specifications

Dimensions

The dimensions diagram shows the required cutouts for installation. For the fitting with a canister, a cutout diameter of 241mm is specified. Without a canister, a cutout diameter of 235mm is required. The fitting itself has a diameter of 180mm, a height of 75mm, and a recess of 45mm.

Adequate Drainage

The adequate drainage diagram illustrates how to ensure longevity for the inground light. It recommends a slight decline on the ground level to allow water to run away from the fitting. A 100mm space below the light fitting's canister, filled with 100mm to 150mm of crushed rock, is shown to facilitate proper drainage.

Important Safety Issues

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required; if not within this allowance, warranty will be voided.
• Aluminium and 304SS fittings must not be installed within 5km of any salt water environments.
• All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
• All o-rings and seals must be in place correctly to maintain warranty.
• When installing inground light fittings, adequate drainage must be allowed to prevent fittings from sitting in water for a long period of time. If no drainage is allowed, warranty will be voided.
• See sample adequate drainage diagram for correct installation method.
• This form may be updated at any time due to product improvements; please check online installation form for most current version.

Steps for Installation: HV1845T

1. Make sure that the electrical circuit is free of voltage (master switch off).
2. Make a hole where fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
3. Insert canister, and ensure that the top is level with ground or floor. Failure to do so will void warranty.
4. Using an appropriate 12v DC LED Driver - DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V.
5. Connect the cable - If more than one fitting installed, wiring must be done in parallel.
6. Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together.
7. Solder all joins using solder and either a heat gun or butane gas torch.
8. Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
9. Heat the heat shrink or crimp the gel cap making sure all connections are covered.
10. Make sure the seals are still in place and screws are tight to avoid any water penetration.
11. Fitting is preset to 3000k; locate cap on bottom of fitting and remove by twisting anti-clockwise. Slide switch to desired colour temperature, reattach cap making sure it is tight.
12. Insert fitting into canister.
13. Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
14. All connections must be carried out carefully; inspect all contacts before switching back on the electric circuit.

Steps for Installation: HV1845RGBW

1. Make sure that the electrical circuit is free of voltage (master switch off).
2. Make a hole where fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
3. Insert canister, and ensure that the top is level with ground or floor. Failure to do so will void warranty.
4. Connect the cable.
5. Use an appropriate 12v DC LED Driver and RGBW LED Controller - DO NOT CONNECT LIGHT FITTING DIRECT TO 240V.
6. Do this by stripping back the cable on both fitting and cable run and twist cable together, making sure all colours are correctly joined to the correct colour:
   • Black = Positive
   • Red = Red
   • Green = Green
   • Blue = Blue
   • White = White
7. Solder all joins using solder and either a heat gun or butane gas torch.
8. Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
9. Heat the heat shrink or crimp the gel cap making sure all connections are covered.
10. Connect cable run to RGBW Controller.
11. Connect the RGBW Controller to 12v DC LED Driver.
12. Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
13. All connections must be carried out carefully; inspect all contacts before switching back on the electric circuit.

Steps for Installation: HV1845-F-SH

1. Remove nuts on back of fitting and set aside.
2. Remove cover and replace with security face.
3. Reattach nuts and tighten, making sure seals are still in place.
4. Insert fitting into canister.
5. Insert screws and tighten.

Contact and Additional Information