SW-MOTECH Legend Gear LR2 Tail Bag Mounting Instructions

Legend Gear Hecktasche LR2 / Legend Gear Tail Bag LR2

DEUTSCH - Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. >> www.sw-motech.com

Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference. SW-MOTECH assumes no liability for damages caused by improper fixation and handling.

This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers' accessory parts is not guaranteed. Installed accessories can change driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Please observe any country-specific regulations concerning vehicle registration.

PREPARATION

Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Make sure to use only the appropriate tools. During installation have another person help you.

FUNCTION CHECK

This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type.

ATTENTION

All components of the product must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream. After mounting, make sure there are no clearance issues while the suspension is both compressed and extended.

ATTENTION: Before riding and at each stop (every 200 km) check proper fixation of the product!

After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.

LOADING INFORMATION

ATTENTION: Riding with this product may affect the motorcycles driving and braking performance! Make sure weight is evenly distributed!

ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!

Never store pointy or sharp-edged objects in the product, which could cause injury to persons or damage to the vehicle/product.

Use a waterproof inner bag/raincover to protect your luggage from moisture. Additionally protect sensitive luggage (e.g., electronic equipment) from moisture with a plastic bag.

ATTENTION: Maximum load: 12 kg / 26.4 lbs! The maximum vehicle load specified by the manufacturer must not be exceeded!

ATTENTION: Maximum speed with this product: 130 km/h!

PARTS LIST & CARE

Parts List

• 1x Tail Bag LR2
• 2x 4x Strap
• 3x 2x License Plate Fixation
• 4x 1x Waterproof Innerbag
• 5x 2x Adhesive Protection Film
• 6x 2x Compression Strap

Features (from left to right):

Mounting straps; Attaching possibility for additional luggage; Waterproof innerbag with Velcro fixation.

CARE

Clean the product periodically or after each trip, as dust and dirt have a wear-effect and permanent stains can be prevented. Clean the product after riding in salty conditions, to avoid damage from salt.

First remove dust and encrustations with a soft dry brush. Remove stubborn deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer! Then rinse with clear water.

Before re-use dry the product for at least 24 hours in the air (not in direct sunlight).

We recommend to impregnate the cotton textile surface of the product in regular intervals or after intensive cleaning with a commercial wax impregnation (e.g. from Fjällräven).

ATTENTION: Because the textile surfaces material is a natural fiber, it will experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this!

ATTENTION: Dirt on the product and vehicle has an abrasive effect and can damage surfaces, such as the paint. Make sure that all areas of the vehicle, which have contact with the product or parts of the product as straps, are protected with an adhesive protection film from scratches and abrasions. SW-MOTECH assumes no liability for paint damage and abrasions.

MOUNTING / FIXATION

Step 1

There are many ways to attach the tail bag (1) in the rear area of the vehicle (e.g. latching hooks or reliable indicators). SW-MOTECH recommends the mounting with the license plate fixations (3). Attach the license plate fixations (3) with the original nuts and screws of your license plate. Alternatively, the straps (2) can get entangled under the fender.

Step 2

On both sides entangle two straps (2) to appropriate and reliable attachment points at the rear of the vehicle (as described in step 1).

Step 3

Move both straps (2) through the marked buckles of the tail bag (1), as shown in the picture.

Step 4

On both sides entangle two straps (2) to appropriate and reliable attachment points of the vehicle (e.g. passenger footrest mounts, vehicles frame etc.).

Step 5

Move both straps (2) through the marked buckles of the tail bag (1), as shown in the picture.

Step 6

Pull on the straps (2) until the tail bag (1) is centred and sits tightly on the passenger seat. Check the proper fit.

Step 7

ATTENTION: Make sure after tightening the tail bag (1), that the ends of the straps (2) are secured from flapping, as shown in the detail drawing.

Step 8

ATTENTION: Make sure after tightening the tail bag (1), that the ends of the straps (2) are secured from flapping, as shown in the detail drawing.

Step 9

FUNCTION CHECK: All components of the product must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream. For this reason compress the suspension fully several times with your vehicle stationary.