Licensed Lamborghini Aventador SV Ride-On (12V)
Item Number: 060-ROT-17L
Note: Product appearance and colors may vary from the photo.
ATTENTION
This vehicle is packed with the battery disconnected. Connect the battery before use. This manual contains important safety, performance and maintenance information. Read the manual before allowing your child to ride your new electric ride-on toy. Keep this manual properly for future reference.
A detailed line drawing shows the front view of the Lamborghini Aventador SV ride-on toy car, highlighting its sporty design with a low profile, sharp angles, and prominent front grille. The steering wheel and interior details are visible, along with the large, detailed wheels.
Safety Instruction
When using electrical products, basic safety precautions should always be followed, including the following:
WARNING:
Read all Instructions before operating this product
- To protect against electrical shock, do not immerse cord, charger, transformer, battery, or the product in water or other liquid.
- Only use charging devices, transformer, and battery provided or recommended by the manufacturer.
- For your children's safety, the product should be assembled by an adult.
- This toy is only intended for children between 37 - 72 months of age.
- Close adult supervision is necessary when your child is operating this product.
- Disconnect the battery if not used for a long time.
- Personal protective equipment such as a helmet is needed when operating this product.
- Do not use this product as a traffic tool.
- To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water; always wear shoes, and never allow more than 1 rider.
- Do not use this product on a slippery surface.
- Always keep hands, hair, and clothing away from moving parts.
- Maximum user's weight for this product is 66 lb / 30 kg.
- Do not change, modify or add any electrical wiring on this product.
- Avoid using this product in a tight environment to prevent damage to the product or injury to the user.
- Do not use this product in the dark. Only operate this product during daytime or in a well-lit area.
- For your child's safety, please make sure the seat belt is securely fastened when operating this product.
- Personal protective equipment such as a helmet is needed when operating this product.
Diagrams illustrate correct and incorrect helmet fitting. The correct fitting shows the helmet covering the forehead, while the incorrect fitting shows the forehead exposed and vulnerable.
WARNING: PREVENT FIRE
- Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system.
- Use of the wrong type of battery or charger could cause a fire or explosion resulting in serious injury.
- The battery must be handled by adults only. The battery is heavy and contains sulfuric acid (electrolyte). Dropping the battery could result in serious injury.
- Never allow children to charge the battery. Battery charging must be done by adults only.
- Never lift or carry the battery by the wires or connector. This can damage the battery and possibly cause a fire resulting in serious injury. Lift and carry the battery by the case only.
- Examine the battery, charger, and their connectors for excessive wear or damage each time you charge the battery. If damage or excessive wear is detected, do not use the charger or the battery until you have replaced the worn or damaged part.
WARNING:
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.
Avoid continuously hitting into an obstacle to prevent overheat or damage to the motor. Drive away or remove the obstacle as soon as possible.
Product Specification
- Motor: 12V, 390#, 25W*2
- Charger: 12V500mA
- Speed: 0.7 ~ 2.2 mph (1.2 ~ 3.5 km/h)
- Suitable Age: 37-72 months
- Maximum User Weight: 66 lb / 30 kg
- Dimension: 45.27" x 25.82" x 17.71" (1150 x 656 x 450 mm)
- Battery charge time: 8 ~ 12 hours
- First charging time: 8 ~ 12 hours
- Max charging time: 20 hours
- Battery (Temperature Tolerance): -20°C (68°F) TO 60°C (140°F)
- Operation Time: 1-2 hours
Parts and Feature
The following parts are included with the ride-on toy:
- A (Steering Wheel)
- C (Left Mirror)
- D (Right Mirror)
- E (Remote Control)
- F (Rear Wing)
- G (Wheel)
- H (Wheel Cover)
- I (Seat)
- L (Spanner)
- Q (Charger)
- R (Windshield)
- T (M4x12 Screw)
Illustrations show each of the listed parts.
Assembly Instruction
Estimated Assemble Time: 40 mins
Tools Needed:
- Screw Driver (not included)
Some parts are small and have sharp edges. Do not let children handle parts or the assembly. This product should be assembled by an adult.
Step 1: Remove Nuts (2) and Washer (1) from the front axle, and remove Nuts (4) and Washer (5) from the rear axle. A diagram shows the underside of the car with arrows indicating where to remove these parts.
Step 2: Slide Wheel (G) to the front axle and replace Washer (1) and Nut (2), then snap on Wheel Cover (H). Slide Wheel (G) to the rear axle and replace Washer (5) and Nut (4), then snap on Wheel Cover (H). A diagram illustrates the wheels being attached to the axles with washers and nuts, and wheel covers being snapped on.
Step 3: Connect terminal (6) from the Steering Wheel (A) to the terminal (7) on the Steering Column (8). Insert the Steering Wheel into the Steering Column. A diagram shows the steering wheel connection and insertion into the steering column. Another diagram shows the Left Side Mirror (C) and Right Side Mirror (D) being inserted into the sides of the vehicle.
Step 4: Assemble Windshield (R) to the vehicle body. A diagram shows the windshield being attached to the front of the car.
Step 5: Assemble Rear Wing (F) to the two slots on the vehicle body. A diagram shows the rear wing being attached to the back of the car.
Step 6: Install the Seat (I) to the car and align the hooks on the back to the groove on the car body. Secure it in place with 2 M4x12 screws (T). A diagram shows the seat being installed and secured with screws, with a close-up view of the hook and groove alignment.
User Instruction
Control the vehicle
Control Panel
Controls the ON / OFF of the vehicle and the audio playing system. See detailed instruction on the Control Panel User Instruction on page 10-11.
Engine Sound Button
Press the button to play the engine sound. When a USB and MP3 device is connected to the vehicle, pressing the button will play the next song. Press and hold the button to increase volume.
Horn Button
Press the button to honk. Press and hold the button to decrease volume.
Foot Pedal
Press the foot pedal to move the vehicle. Release the foot pedal to stop the vehicle.
A diagram shows the interior of the ride-on car, highlighting the steering wheel with the Engine Sound/MP3 player button and Horn Button, the Control Panel, and the Foot Pedal.
User Instruction (Control Panel)
- FM Radio Search Button: Press this button to search FM channels when in FM mode.
- FM Button: Press the FM button to enter FM mode.
- Mode Button: Press the Mode button to switch between USB, AUX, and Bluetooth (Kidzone Ride-on).
- Forward Button: Press the forward button, and step on the foot pedal to move the vehicle forward.
- Reverse Button: Press the reverse button, and step on the foot pedal to move the vehicle in reverse.
- High / Low Speed Button: Press the speed button to switch between high and low speed.
- Previous / Decrease Volume Button: Press the button to play the previous music track. Press and hold the button to decrease the volume.
- Light Button: Press the button to turn ON / OFF the vehicle light.
- Next / Increase Volume Button: Press the button to play the next music track. Press and hold the button to increase the volume.
- ON/OFF Button: Press and hold the button to turn ON or OFF the vehicle. Short press the button to pause or play music track.
- Flash Drive Port: Port for flash drive with MP3 files. NOTE: The player can only support MP3 format files.
- Voltage Display Screen: The battery level will be displayed on the screen.
- AUX Port: Connect music device to the vehicle player via AUX cable.
A detailed diagram of the control panel is provided with numbered buttons corresponding to the instructions.
User Instruction (Remote Control)
The remote control should only be used by an adult.
NOTE: Remote control input will always override manual control operation.
Change Battery
Remove the cover on the back of the controller and insert two AAA (LR03) batteries. NOTE: If the remote control is not used for 10 seconds, it will shut down automatically. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
Establish Connection
- Turn off the Power of the vehicle.
- Insert battery into the remote control, and the LED indicator will flash.
- Turn on the Power of the vehicle. When the 2 LED indicators on the remote control remain on, it indicates a successful pairing.
- The connection will remain unless the batteries on the remote control are replaced.
The remote control will automatically enter sleep mode if not used for a long period, and the LED indicator will turn off. Press any button to wake the remote control up.
Diagrams show the battery compartment of the remote control and the layout of the remote control buttons: Stop, Reverse, Forward, Left, Right, and Speed Selection Button, along with the LED Indicator.
User Instruction (Charging)
WARNING!
The battery should only be charged by an adult. The battery is not replaceable.
Charging the battery
- The vehicle must be OFF when charging.
- Before the first use, the battery should be charged for around 12 hours. Do not charge the battery for more than 20 hours to avoid overheating or damage to the charger or the battery.
- Recharge the battery if the vehicle operates slowly.
- The battery is not replaceable.
Charge the battery at least once a month, even if not operating the vehicle, to maximize the battery life.
A step-by-step diagram illustrates the charging process: connecting the charger to the vehicle's charging port.
Care and Maintenance
- Check the product regularly and make sure there are no missing or loose parts. Re-tighten any loose parts if necessary.
- Make sure there are no cracked or broken plastic parts.
- Keep the product away from heat and humid areas; cover it with a tarp when not in use.
- Turn off the product and disconnect the battery if the product is not used for a long period of time.
- Clean the vehicle with a cloth. Use a non-wax furniture polish to restore the shininess of the plastic parts. Do not use abrasive cleaner.
- Do not wash the product with a hose or immerse any parts in water or other liquid.
- Occasionally use lightweight oil to lubricate moving parts.
Troubleshooting
| Problem | Possible Reason | Solution |
|---|---|---|
| Vehicle does not move | Low Battery | Fully charge the battery |
| Fuse Protection | Wait 5 - 20 seconds for the fuse to reset | |
| Disconnected / Badly connected battery | Reconnect the battery | |
| Failed battery / engine | Contact Customer Service | |
| Battery not last long | Low Battery | Fully charge the battery |
| Old Battery | Replace battery if necessary | |
| Vehicle runs very slow | Low Battery | Fully charge the battery |
| Old Battery | Replace battery if necessary | |
| Vehicle is overloaded | Make sure user's weight is under 66 lb / 30 kg | |
| Vehicle is being used in harsh environment | Avoid using the vehicle in harsh environment | |
| Vehicle needs a push to go forward | Poor wire connection | Check if the battery connectors are firmly connected. Contact Customer Service if necessary. |
| "Dead spot" on motor | Contact Customer Service | |
| Loud grinding sound or clicking sound from the motor or gear box | Damaged motor or gear box | Contact Customer Service |
| Battery does not charge | Disconnected / Badly connected battery | Reconnect the battery |
| Disconnected / Badly connected charger | Make sure the charger is firmly plugged into the power source and connected to the charging port. | |
| Charger not working | Contact Customer Service | |
| Charger becomes warm during charging | Normal | N/A |
FCC ID: 2ARLM-CST-1A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This product conforms to toy safety standards CPSIA and ASTM-F963.
Importer: ONE BIG OUTLET
Importer Address: 19301 E Walnut dr. N. City of industry CA91748 united states
Importer Tel.: 800 - 946 - 6151
Limited Term Warranty (One Year from Date of Purchase)
WARRANTY TERMS
KIDZONE warrants that its merchandise are free from manufacturing defects (workmanship and/or material) and will either give credit or replace defective parts for a period of up to one (1) year from the date of purchase in accordance with the conditions set forth below. If a manufacturing defect is found, KIDZONE should be notified promptly of the defect and supplied a copy of the invoice and delivery ticket. Inspection by a KIDZONE employee or representative may be necessary to verify that a manufacturing defect exists, or you may be required to submit samples to KIDZONE along with a digital image of the defects. If replacement is required in accordance with this warranty and the defective material or merchandise has been discontinued or unavailable, KIDZONE reserves the right to select and supply similar merchandise or offer full credit for the merchandise; otherwise, the same material or merchandise will be supplied for replacement purposes. This warranty is made solely to the retailer and is not transferable under any circumstances. It is the retailer's responsibility to contact KIDZONE with a claim. KIDZONE will not handle claims from consumers directly; all requests must go through the retailer who sold the merchandise to the consumer. KIDZONE advises all retailers to retain invoices for a minimum of one (1) year for warranty purposes. This warranty supersedes and replaces all implied warranties of merchantability and use for a particular purpose. No representative, employee, agent, or any other person is authorized to assume for KIDZONE any additional liability or responsibility in connection with KIDZONE's merchandise except as described above. Implied warranties of merchantability and fitness of the merchandise are limited to a period of one (1) year from the date of purchase. In no event shall KIDZONE be liable for indirect, consequential, or incidental damages of any kind.
ADDITIONAL CONDITIONS
THE FOLLOWING EXAMPLES ARE NOT MANUFACTURER'S DEFECTS:
- Colors may vary slightly from the photo because of photography and printing tolerances.
- Sizes stated in U.S. standard measurements may vary slightly due to products being manufactured using the metric system.
- No returns for buyer's remorse.
- No returns - other than stated above will be accepted.
ADDITIONAL CONDITIONS
WARRANTY IS VOID FOR ANY OF THE FOLLOWING CONDITIONS:
- Improper maintenance or improper use resulting in damage.
- Any product modifications by dealer, consumer, or other parties not authorized by KIDZONE will void this warranty.
- Floor samples sold or products designated "AS IS" at the time of purchase are not covered by the warranty.
- Warranty does not cover minor variations or differences between floor samples or printed illustrations and your product.
- Cost of packaging and shipping to and from KIDZONE is not covered by the warranty unless expressly arranged by KIDZONE.
- This warranty covers only articles of appliances intended for residential use only; it does not cover any industrial, commercial, institutional, or rental use.
- Dissatisfaction due to buyer's remorse.
- Normal wear and tear.
- Damages incurred during transportation.
- Damages incurred during assembling or maintenance.
- Damage incurred by accidents or abuse.
