270W Adapter FSP270-RXAN3

FSP270-RXAN3 Series

Features

Certified IEC 62368-1 & CB 60950-1
Meets USA EISA 2007
Meets Energy Efficiency DOE Level VI
Meets Code of Conduct Version 5 Tier 2
High Reliability
Low Profile
Over Current Protection
Over Temperature Protection
Over Voltage Protection
With PFC Circuit

Safety Standard Approval

Safety standard approvals include CULUS, TÜVRheinland, CE, and FCC compliance. Tested to Comply With FCC Standards for Home or Office Use.

Description

This product is a 240~270 watts AC to DC adapter intended for use in IPC systems, embedded systems, printers, monitors, charging systems, and POS systems that have high wattage demands. This adapter operates at 90 to 264 VAC input voltage. The unit meets CISPR32 EN55032 CLASS B, EN55024, and FCC PART 15B Class B emission limits, and is designed for ITE application.

Input Specifications

Input Voltage: 90-264 VAC

Input Frequency: 47-63 Hz

Input Current: 100Vac, 240Vac / full load ≤ 1.2A

No Load Power Consumption: 115Vac, 230Vac ≤ 0.5W

Touch Current: 264Vac / 50Hz ≤ 0.25mA

Power Factor: 115Vac, 230Vac / full load ≥ 0.9. Provisions for adding harmonic reduction per EN 61000-3-2 must be present.

Efficiency: See rating chart

Power Turn-on Time: At 100Vac / full load, output voltage shall remain regulation ≤ 3Sec

Hold-up Time: At 100Vac or 240Vac / full load, output voltage shall remain regulation ≥ 10ms

Inrush Current: 100Vac, 240Vac / full load, shall be less than the rating of adapter critical component (including rectifiers, fuse, surge, and current limiting device).

Operating Altitude: 5000 meters above sea level

Withstand Voltage: Between AC input and secondary applied DC 4242V, test time 1 minute, cut off current shall be less than 10mA

MTBF: 100Vac, 240Vac / full load, 300,000 hours at 25°C, standard SR332

Output Specifications

Output Voltage/Current: See rating chart

Total Output Power: See rating chart

Protection:

Over Voltage: The adapter will enter into shutdown (no output) if over voltage occurs at the output terminal due to an internal fault. The output trip voltage shall not exceed 29/37* volts. Normal state is restored by AC reset.
Short Circuit & Over Current: When an internal fault occurs, or an external fault (overload or short circuit) is applied to the output, the power supply shall shut down and enter auto-recovery mode.
Over Temperature: The power supply will enter into shutdown when abnormal thermal rise occurs. Normal state is restored by AC reset.
Brown-out: Set at 60Vac~70Vac.

Environmental Specifications

Working Temperature: 0~70°C (de-rating above 40°C)

Storage Temperature: -20~+80°C

Working Humidity: 20~80% RH non-condensing

Storage Humidity: 10~90% RH non-condensing

EMC Performance

EN55032: Class B conducted, Class B radiated

FCC: Class B conducted, Class B radiated

VCCI: Class B conducted, Class B radiated

EN61000-3-2: Meets Class D

EN61000-3-3: Meets regulation

EN61000-4-2 (Electrostatic Discharge): Air discharge: ±15 KV, Contact discharge: ±8KV (Criterion A)

EN61000-4-3 (Radiated Immunity): 80~1000 MHz, 3V/m, 80% AM (1kHz) (Criterion A)

EN61000-4-4 (Electrical Fast Transient/Burst): Impulse: ±1kV applied to L,N (Criterion A)

EN61000-4-5 (Surge): ±1kV applied differential mode, ±2kV applied common mode (Criterion A)

EN61000-4-6 (Conducted Immunity): 0.15~80 MHz, 3Vrms, 80% AM (1kHz) (Criterion A)

EN61000-4-8 (Magnetic Field): 50 Hz or 60Hz, 1A/m (Criterion A)

EN61000-4-11 (Voltage Dips/Interruptions):

Voltage Dips: >95% reduction for 0.5 period (Criterion A), 30% reduction for 25 period (Criterion B)
Voltage Interruptions: >95% reduction for 250 period (Criterion B)

Power De-rating: For 100Vac or 240Vac input, de-rating applies from 40°C (100% load) up to 70°C (50% load). Specific de-rating percentages are based on adapter critical component ratings and FSP specifications.

Derating Curves

Input Voltage Derating Curve: A line graph illustrating output power percentage versus input voltage (Vac). The curve shows that at 90Vac input, the output power is 100%. As the input voltage increases to 264Vac, the output power decreases to approximately 80%.

Output Power Derating Curve: A line graph illustrating output power percentage versus ambient temperature (°C). The curve shows that at 0°C, the output power is 100%. As the temperature increases to 70°C, the output power decreases to approximately 50%.

Output Voltage/Current Rating Chart

Model	Output Voltage	Output Current	Wattage	AC Inlet	Efficiency (DOE Level VI)	Efficiency (CoC V5 Tier 2)
FSP270-RHAN3	12V	20A	240W	C14	≥89%	≥88%
FSP270-RBAN3	19V	14.21A	270W	C14	≥88%	≥89%
FSP270-RAAN3	24V	11.25A	270W	C14	≥88%	≥89%
FSP270-RFAN3	48V	5.62A	270W	C14	≥88%	≥89%
FSP270-RWAN3	54V	5A	270W	C14	≥88%	≥89%

Mechanical & AC Connector Specifications

Diagrams illustrate the physical dimensions and AC connector details.

Overall Dimensions: 204.0±1.0 mm (Length) x 87.6±1.0 mm (Width) x 41.5±1.0 mm (Height).

AC Input Connector: IEC C14 type.

AC Cable: UL11353 12AWG BLACK, with a length of 1200±30 mm.

Housing: JWT C4202H00-2X3P or equivalent.

Rating Label: Located on the housing.

Power Indicator: Blue LED.

Cable Tie: Steel wire, PVC plated.

DC Connector Specifications (FSP270-RFAN3)

Diagrams detail the DC output connector and cable configuration.

DC Output Connector: Plug dimensions: 5.5mm (outer diameter) * 2.5mm (inner diameter) * 9.5mm (length).

Polarity: Center positive (+), outer negative (-).

Cable Color Coding: WHITE for positive, BLACK for negative.

Cable Lengths:

100±30 mm (from connector to first heat shrink)
70±30 mm (second heat shrink section)
1200±30 mm (total cable length)

Heat Shrink Tubing: Black and White.