Immergas Victrix Pro IPX5D Outdoor Cover Kit Installation Guide

General Warnings

All Immergas products are protected with suitable transport packaging. The material must be stored in a dry place protected from the weather.

This instruction manual provides technical information for installing the Immergas kit. For other issues related to kit installation, such as workplace safety, environmental protection, and accident prevention, it is necessary to comply with regulations in force and good practice principles.

Improper installation or assembly of the Immergas appliance, components, accessories, kits, and devices can cause unexpected problems for people, animals, and objects. Read the instructions provided with the product carefully to ensure proper installation.

Installation and maintenance must be performed in compliance with regulations in force, according to the manufacturer's instructions, and by professionally qualified staff with specific technical skills in the plant sector, as envisioned by law.

List of Compatible Appliances

• Victrix Pro 35/55/80 V2
• Victrix Pro 100/120 V2
• Victrix Pro 150 V2
• Victrix Pro 180 V2

Cover Kit Assembly (Fig. 1)

For Victrix Pro 35/55/80 V2 Version:

1. Remove the plug (11) and the relevant gasket (12) present in the intake hole.

2. Install the upper cover (10), fixing it using the 4 screws (13) present in the kit, positioning the relevant gaskets (14).

3. Engage the 90° bend (4) with the male end (smooth) in the female end (with lip seal) (7) of the flange unit until it reaches the end stop. Introduce the gasket, making it run along the bend. Fix it using the metal-sheet steel plate (6) and tighten by means of the clip (5) present in the kit, making sure to block the 4 gasket flaps (7).

4. Make sure that the air vent valve (1, Fig. 3) comes out of the thermoformed cover (2, Fig. 3) and that the gasket (3, Fig. 3) is correctly assembled on the valve itself in order to guarantee the tightness (Fig. 3).

5. Fit the male end (smooth) of the exhaust terminal (2) into the female end of the 90° bend (4), making sure that the relevant wall sealing plate (1) is already fitted and that the gasket (3) is inside the bend (4); this will ensure hold and joining of the elements making up the kit.

6. Coupling of extension pipes: To install pushfitting extensions with other elements of the flue, proceed as follows: Couple the pipe or elbow with the male side (smooth) in the female side (with lip seal) to the end stop on the previously installed element. This will ensure sealing efficiency of the coupling.

Attention: For correct boiler configuration, refer to the relative instruction booklet.

The cover kit includes:

• N° 1 Thermoformed cover (10)
• N°1 Gasket clamping plate (6)
• N°1 Bend 90° Ø 80 gasket (7)
• N°1 Gasket tightening clip (5)
• N° 1 Air vent valve gasket (9)
• N° 1 Air vent valve plate (8)

The terminal kit includes:

• N° 1 Gasket (3)
• N° 1 Bend 90° Ø 80 (4)
• N° 1 Exhaust pipe Ø 80 (2)
• N° 2 Wall sealing plates (1)

Cover Kit Assembly (Fig. 4)

For Victrix Pro 100/120/150 V2 Version:

1. Remove the plug (11) and the relevant gasket (12) present in the intake hole.

2. Install the upper cover (10), fixing it using the 4 screws (13) present in the kit, positioning the relevant gaskets (14).

3. Engage the adapter (15) with the male end (smooth) in the female end (with lip seal) (7) of the flange unit until it reaches the end stop. Introduce the gasket, making it run along the adapter. Fix it using the metal-sheet steel plate (6) and tighten by means of the clip (5) present in the kit, making sure to block the 4 gasket flaps (7).

4. Engage the 90° bend (4) with the male end (smooth) in the female end of the adapter (15), making sure that the gasket (16) is present inside the adapter (15).

5. Make sure that the air vent valve (1, Fig. 6) comes out of the thermoformed cover (2, Fig. 6) and that the gasket (3, Fig. 6) is correctly assembled on the valve itself in order to guarantee the tightness (Fig. 6).

6. Fit the male end (smooth) of the exhaust terminal (2) into the female end of the 90° bend (4), making sure that the relevant wall sealing plate (1) is already fitted and that the gasket (3) is inside the bend (4); this will ensure hold and joining of the elements making up the kit.

7. Coupling of extension pipes: To install pushfitting extensions with other elements of the flue, proceed as follows: Couple the pipe or elbow with the male side (smooth) in the female side (with lip seal) to the end stop on the previously installed element. This will ensure sealing efficiency of the coupling.

Attention: For correct boiler configuration, refer to the relative instruction booklet.

The cover kit includes:

• N° 1 Thermoformed cover (10)
• N°1 Gasket clamping plate (6)
• N°1 Adapter D. 110/100 gasket (7)
• N°1 Gasket tightening clip (5)
• N° 1 Air vent valve gasket (9)
• N° 1 Air vent valve plate (8)

The terminal kit includes:

• N° 1 Gasket (3)
• N° 1 Bend 90° Ø 100 (4)
• N° 1 Exhaust pipe Ø 100 (2)
• N° 2 Wall sealing plates (1)
• N° 1 Adapter D.110/100 (15)
• N° 1 Adapter D.110/100 gasket (16)

Cover Kit Assembly (Fig. 7)

For Victrix Pro 180 V2 Version:

1. Remove the plug (11) and the relevant gasket (12) present in the intake hole.

2. Install the upper cover (10), fixing it using the 6 screws (13) present in the kit, positioning the relevant gaskets (5).

3. Engage the 90° bend (4) with the male end (smooth) in the female end (with lip seal) (7) of the flange unit until it reaches the end stop, making sure the gasket is present (3). Introduce the gasket, making it run along the bend. Fix it using the metal-sheet steel plate (6) present in the kit, making sure to block the 4 gasket flaps (7).

4. Make sure that the air vent valve (1, Fig. 9) comes out of the thermoformed cover (3, Fig. 9) and that the gasket (2, Fig. 9) is correctly assembled on the valve itself in order to guarantee the tightness (Fig. 9).

5. Fit the male end (smooth) of the exhaust terminal (2) into the female end of the 90° bend (4), making sure that the relevant wall sealing plate (1) is already fitted and that the gasket (3) is inside the bend (4); this will ensure hold and joining of the elements making up the kit.

6. Coupling of extension pipes: To install pushfitting extensions with other elements of the flue, proceed as follows: Couple the pipe or elbow with the male side (smooth) in the female side (with lip seal) to the end stop on the previously installed element. This will ensure sealing efficiency of the coupling.

Attention: For correct boiler configuration, refer to the relative instruction booklet.

The cover kit includes:

• N° 1 Thermoformed cover (10)
• N°1 Gasket clamping plate (6)
• N°1 Bend 90° D.160 gasket (7)
• N° 1 Air vent valve gasket (9)
• N° 1 Air vent valve plate (8)

The terminal kit includes:

• N° 1 Gasket (3)
• N° 1 Bend 90° D.160 (4)
• N° 1 Exhaust pipe D.160 (2)
• N° 2 Wall sealing plates (1)