Digital Projection Alarm Clock

1 FEATURES

Digital Projection Alarm Clock with AM/FM Radio, USB port and LED (USB charging).

Front View: Features TIME, PM indicator, PROJECTOR, RADIO, MEM, Q1, 2, SL, ALARM 1 ON, ALARM 2 ON, USB CHARGING PORT.

Back View: Features INSERT DC JACK TO POWER UP YOUR UNIT, INSERT 1X CR2032 LITHIUM BATTERY (INCLUDED).

Top View: Features VOL, SLEEP, RADIO, DIMMER, SET, AL, DOWN, UP/PROJECT, VOLUME, ALARM 1,2, RADIO, SLEEP, SET, SNOOZE, DIMMER.

2 START UP

Please remove the plastic insulator tab from the button battery compartment in the back. Connect the AC/DC adapter to the power supply and the other end to the USB seat on the back of the clock to start operation.

Note: When the power is off, the LED screen will not show, and the radio and alarm cannot function. The backup battery only retains the basic settings of time and alarm.

Diagram: Shows USB CHARGING PORT, INPUT 5V, and INSERT 1X CR2032 LITHIUM BATTERY (INCLUDED).

3 SETTINGS

Time Setting (Turn off the radio)

1. Press and hold the “Set” button for 3 seconds. The hour digits flash. Press ▲ or ▼ to set the hour. (Long press ▲ or ▼ will accelerate setting at high speed.)
2. Press “Set” again. The minute digits flash. Press ▲ or ▼ to set the minute. (Long press ▲ or ▼ will accelerate setting at high speed.)
3. Press “Set” again. The display shows “24H” and flashes. Press ▲ or ▼ to select “12H” or “24H”.
4. Press “Set” again. The display shows “09” and flashes. Press ▲ or ▼ to select your snooze time from 5 to 60 minutes.
5. Press “Set” or if no operation occurs within 20 seconds, it will exit the current setting mode.

Note: When the 12-hour time format is selected, the “PM” LED will appear on the screen in the afternoon.

Diagrams: Illustrate the sequence of time setting with display examples.

Alarm Setting

1. Press “AL” once. The ALARM 1 LED and the hour digits will flash. Press ▲ or ▼ to set the hour duration. (Long press ▲ or ▼ will accelerate setting at high speed.)
2. Press “AL” again to set the minutes. Press ▲ or ▼ to set the minute duration. (Long press ▲ or ▼ will accelerate setting at high speed.)
3. Press “AL” again. The LED displays “OFF” (alarm off). Press ▲ or ▼ to select the alarm mode (“rd” = wake-to-radio, “bu” = wake-to-buzzer, “OFF” = alarm off). When “rd” or “bu” is selected, the related alarm will turn on.
4. For a second alarm, repeat steps 1-3. (Note: The second alarm will be indicated by “ALARM 2” on the display.)
5. Press “AL” or if no operation occurs within 20 seconds, it will exit the alarm setting mode.

Note: When alarm “ALARM 1” or “ALARM 2” is being set, an “A1” or “A2” LED will appear on the bottom of the display.

Diagrams: Illustrate alarm setting with display examples like “OFF”, “6:59”, “7:00”.

FM Radio

FM Setting:

1. To turn on the radio, press “RADIO/SLEEP” once. The display shows “ON” and then the radio frequency readings in MHz.
2. Press ▲ or ▼ once to turn the radio to a desired station. Press and hold ▲ or ▼ to scan for the next clear station.
3. To adjust the volume, press “VOL” once. The display shows “L00”. Press ▲ or ▼ to adjust the volume from L00 (minimum) to L15 (maximum).
4. Press “SNOOZE/DIMMER” to turn off the radio.

Note: Keep your radio away from interference sources or other electronic devices that may cause interference to the radio.

Reset Memory: This clock radio features 15 preset FM station memories.

1. Turn on the radio and select a station to memorize.
2. Press and hold “SET” until the “MEM” LED appears and “01” flashes. Press “SET” once to store Memory 1.
3. Press ▲ or ▼ to select another station to memorize, then press and hold “SET” until “MEM” LED appears and “01” flashes. Press ▲ once, “02” appears, press “SET” once to store Memory 02.
4. Repeat step 2-3 to preset memories 3 to 15.
5. To access a preset station, press “SET” once while the radio is on.
6. To edit a preset station, select another station and repeat steps 2-4. This overrides previous settings.

Diagrams: Show display examples for radio frequency and volume adjustment.

Sleep Timer

1. Press “RADIO/SLEEP” twice to enter sleep mode. The sleep LED “SL” and sleep time “05” (5 minutes) appear on the display.
2. Press “RADIO/SLEEP” to adjust the sleep timer from 5, 10, 15, 30, 45, 60, 75, 90, or OFF.
3. When the display returns to showing the time, press “RADIO/SLEEP” twice to display the remaining sleep time.
4. The radio will play for the programmed sleep time and then shut off automatically.

Diagrams: Illustrate sleep timer settings with display examples.

Use Projection

1. In clock mode, press ▲ once in AC mode to turn on the projection (bright). Press again to adjust the brightness (from bright to slightly bright to off; default is off).
2. When the projection is on, press and hold ▲ to revolve the projection view. Press the project key to rotate the projection 180 degrees.

Note: There is no projection function in battery-powered mode.

Diagrams: Show projection display examples with 180° rotation.

Brightness Control

In clock mode, press “SNOOZE/DIMMER” once to adjust the LED display brightness.

1. Brightness levels: Slightly Bright (default) → Bright → Off → Dim.
2. Press and hold the “SNOOZE/DIMMER” button for 2 seconds to select the on/off of Auto mode.

If “AU” is selected, the LED display will automatically enter low brightness mode in dark environments. If “OFF” is selected, brightness can only be controlled manually (default is “OFF”).

Note: This can only be done when the radio is off and the unit is not sounding.

Diagrams: Show display examples for “OFF”, “AU” (Auto Mode), and “OFF” (Manual Mode).

Charging

Connect the charging cable of your mobile phone to the USB port at the back of the unit, then connect the other end to your mobile phone or other equipment. The clock radio will charge the mobile phone automatically.

Notes:

1. Use the original cable of your mobile phone for charging.
2. Charging with this USB port may take a long time.

Diagram: Shows USB charging connection.

4 RESTORE FACTORY DEFAULT

If time errors occur, possibly due to electrostatic interference from other equipment, you can resolve this by removing the power supply and the backup battery. This will restore the clock to its factory default settings. Repower the clock and set the functions.

Diagram: Shows the back of the unit with DC IN and battery compartment.

5 PRECAUTION

1. Do not place the electronic clock in environments with high temperatures, water, or direct sunlight.
2. When placing the clock on furniture, use a cloth or other protective material to prevent damage to the furniture.
3. If necessary, use a flannel with a little soapy water to clean the clock. Avoid using substances like gasoline, thinner, or similar liquids, as they can damage the clock's surface. Always cut off the power before cleaning.
4. If the clock will not be used for an extended period (a month or longer), remove the battery to prevent corrosion. If the battery compartment is corroded or dirty, clean it and replace the battery promptly.
5. Do not disassemble this product.

Diagrams: Show symbols for not exposing to water, not placing on furniture, cleaning with cloth, and not disassembling.