Digital Projection Alarm Clock User Manual

Unit Features

This user manual provides instructions for the Digital Projection Alarm Clock.

Front View

The front of the unit features:

• Digital Display: Shows time, temperature (°C/°F), and humidity (%).
• Indicators: Projection, Radio, ALARM 1, ALARM 2.
• Buttons:
  • [SET]
  • [VOLUME]
  • [ALARM]
  • [RADIO/SLEEP]
  • [DOWN]
  • [SNOOZE/LIGHT]
  • [UP/PROJECT]

Back View

The back of the unit features:

• Projector lens
• Antenna
• [USB] charging port
• DC power jack
• Battery compartment for backup lithium battery

Start Up

To start the unit:

1. Remove the plastic insulator tab from the button battery compartment on the back.
2. Connect the power cable into the DC power jack on the back of the clock.
3. Plug the power cable into a wall socket.
4. The LED display will turn on.

Note: When power is off, the LED display, radio, and alarm will not function. The backup battery retains basic time and alarm settings.

Settings

Time Setting

1. Press and hold [SET] for 3 seconds. The display shows "24H" and flashes.
2. Press [UP/PROJECT] or [DOWN] to select "12H" or "24H" format.
3. Press [SET] again. The hour digits flash. Press [UP/PROJECT] or [DOWN] to set the hour. (Long press accelerates setting).
4. Press [SET] again. The minute digits flash. Press [UP/PROJECT] or [DOWN] to set the minute. (Long press accelerates setting).
5. Press [SET] or wait 10 seconds without operation to exit setting mode.

Note: In 12-hour format, a [PM] icon appears for afternoon. Press and hold [UP/PROJECT] for 3 seconds to switch between 12H and 24H formats.

Alarm Setting

1. Short press [ALARM] once to turn alarm on/off. Sequence: Alarm 1 ON → Alarm 2 ON → Alarm 1 OFF → Alarm 2 OFF.
2. Short press [ALARM] again to select the alarm (Alarm 1 or Alarm 2). The corresponding [AL] icon flashes.
3. With the desired alarm selected and flashing, press and hold [ALARM] for 3 seconds to enter setting mode. The sequence is: Hour → Minute → Snooze time → Alarm mode. The setting object flashes.
4. Adjust values using [UP/PROJECT] or [DOWN]. Press [ALARM] once to confirm and move to the next setting.
5. Default snooze time is 5 minutes ("05" flashes). Press [UP/PROJECT] or [DOWN] to set snooze time from 5 to 60 minutes.
6. Press [UP/PROJECT] or [DOWN] to select alarm mode: "rd" (wake-to-radio) or "bu" (wake-to-buzzer). The selected alarm turns on.
7. For a second alarm, repeat steps 2-6. The display shows "ALARM 2".

Alarm ON/Alarm OFF

1. When an alarm is set, "ALARM 1" or "ALARM 2" icon appears. When an alarm sounds, the icon flashes. Press [SNOOZE/LIGHT] once to silence the alarm temporarily; it will sound again after the set snooze duration.
2. Press any button other than [SNOOZE/LIGHT] once to stop the alarm. The alarm will sound again the next day, and the icon will remain.
3. If the second alarm activates while the first is sounding or in snooze mode, the second alarm overrides the first, resetting the first alarm for the next day.
4. If the radio is selected as the alarm tone, it will play at the last used station and volume.
5. The radio alarm will continue until manually stopped.

Program the Radio

FM Setting

1. Press [RADIO/SLEEP] once to play radio. The display shows "ON" then the frequency (76.0 MHz - 108 MHz).
2. Briefly press [SET]. The radio scans and automatically saves frequencies as 01, 02, 03, etc. It stops on the first saved station.
3. Press [UP/PROJECT] or [DOWN] to select stored stations.
4. To adjust volume, briefly press [VOLUME]. The display shows "L10". Press [UP/PROJECT] or [DOWN] to adjust volume from L00 (minimum) to L15 (maximum).
5. Press [SNOOZE/LIGHT] to turn off the radio.

Note: Keep the radio away from interference sources or other electronic devices.

Sleep Timer

1. Press [RADIO/SLEEP] twice to enter sleep mode. The display shows "SL" and the sleep time (e.g., "05" for 5 minutes).
2. Press [RADIO/SLEEP] to adjust the sleep timer: 5, 10, 15, 30, 45, 60, 75, 90 minutes, or OFF.
3. When the display reverts to showing the time, press [RADIO/SLEEP] twice to view the remaining sleep time.
4. The radio will play for the programmed sleep time and then automatically shut off.

Use Projection

1. In clock mode (AC power), press [UP/PROJECT] once to turn on projection (bright). Press again to adjust projection brightness (Bright → Slightly Bright → Off). Default is off.
2. When projection is on, press and hold [UP/PROJECT] to rotate the projection view 180 degrees.

Note: Projection function is not available in battery-powered mode.

Brightness Control

In clock mode, short press [SNOOZE/LIGHT] to adjust the LED display brightness:

• Bright (default)
• Slightly Bright
• Dim
• Off

Press and hold [SNOOZE/LIGHT] for 3 seconds to select the Auto mode (ON/OFF). If "ON", the LED display automatically enters low brightness mode in dark environments. If "OFF", brightness is controlled manually (default is "OFF").

Note: This function is only available when the radio is off and the unit is not sounding.

Night Mode

Night mode automatically sets the LED display to low brightness during a preset period.

1. Short press [SET] to enter night mode settings (default is "OFF"). Use [UP/PROJECT] or [DOWN] to switch. If "ON", night mode is active. Between 18:00 and 6:00 the next day, the display automatically enters low brightness.
2. When night mode is "ON", press and hold [SET] for 3 seconds to enter interval time setting mode: "start hour" → "start minute" → "end hour" → "end minute". The upper center point flashes for start time, lower for end time.

Note: If Automatic Dimming is enabled, Night Mode will not function.

Displays of Thermometer & Humidity

• The default temperature unit is °C.
• Press and hold [DOWN] for 3 seconds to switch between °C and °F.
• Indoor Temperature range: 0°C - 50°C (32°F - 122°F).
• Indoor Humidity range: 20% - 95%.

Charging

Connect your mobile phone's charging cable to the [USB] port on the back of the unit. The clock will automatically charge your mobile phone or other connected equipment.

Notes:

1. Use the original charging cable for your mobile phone.
2. Charging via this [USB] port may take a long time.

Restore Factory Default

If time errors occur, possibly due to electrostatic interference, remove the power supply and backup battery. Then, repower the clock and set the functions again.

Precaution

• Do not place the clock in high temperature, water, or direct sunlight environments. [avoid direct sunlight] [avoid water] [avoid high temperature]
• When placing the clock on furniture, use a cloth or protective material. [use protective material]
• If necessary, clean the clock with a flannel and a little soapy water. Avoid substances like gasoline or thinner, as they will damage the surface. Cut off power before cleaning. [cleaning instructions]
• If the clock will not be used for a long time (e.g., a month or more), remove the battery to prevent corrosion. Clean and replace the battery if the compartment is corroded or dirty. [remove battery if unused]
• Do not disassemble this product. [do not disassemble]