Important Safety Information
CAUTION: RISK OF ELECTRIC SHOCK, DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
WARNING: This product contains lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
Safety Precautions:
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION ON MODIFICATIONS
Any changes or modifications not expressly approved by the grantee of this device may void the authority granted by the FCC to operate the equipment.
At a Glance
Front/Top Panel Controls and Ports
| Label | Description |
|---|---|
| 1. Indicator Light | LED Indicator Light |
| 2. DC 5V Power Port | DC 5V Micro USB charge port |
| 3. On/Off Switch | Switch to turn the unit On/Off |
| 4. USB port | USB Port to plug in a flash drive |
| 5. AUX Input | 3.5mm AUX input |
| 6. Micro SD input | Insert a Micro SD card to listen to MP3 files. |
Top Panel Controls
| Label | Function |
|---|---|
| 7. [Play/Pause] / [Call] | Press to Pause or Resume Playback. Press to Answer/End a call when the speaker is connected to a smartphone via Bluetooth. Press and hold to turn on and off the LED Lights on the speaker. |
| 8. M (Mode Button) | Press to select different inputs (Bluetooth®/FM/USB/Micro SD/AUX). |
| 9. [Previous Track] / [Volume Down] | Press to skip to previous track. Press and hold to decrease the volume. |
| 10. [Next Track] / [Volume Up] | Press skip to the next track. Press and hold to increase the volume. |
Product Description
Bluetooth® Speaker with LED Lights
This Naxa NAS-3082 portable Bluetooth® speaker allows you to take your music just about anywhere you want. Stream your music from any Bluetooth® enabled device at a range of up to 30' or connect your MP3 player or smartphone using the 3.5mm line-in audio jack. LED lighting effects give you a light show for an added enjoyment while you listen to your favorite music or soundtracks. The hands-free Bluetooth® speaker has a built-in microphone which allows you to receive an incoming call while paired with a Bluetooth® enabled smartphone. This lightweight speaker makes it easy for you to take it anywhere and enjoy music on the go.
Speaker Function Parameters
- Frequency response: 80-18,000 Hz.
- FM frequency range: 87.05-108 MHz (±3DB)
- SNR ≥65DB
- Bluetooth® connection distance ≥10M with hands-free function.
- Power input: USB power of 5V-1000mA from AC power adapter (not supplied).
Instructions for Use
Operating Instructions
- Built-in battery.
- DC-5V (0.4-1A) USB power adapter (not supplied).
REMINDER: When charging the battery is completed, please unplug the cable. ⚠️
While the unit is charging, the indicator light will remain on RED. When the unit is fully charged, the light will turn off.
Bluetooth® Mode
Your Bluetooth® speaker can wirelessly stream audio from any Bluetooth® enabled device within the distance of 26-33 ft. Please follow the steps below to setup connection.
- Turn ON the unit.
- The LED lights will flash on the unit indicating your speaker is powered on and in "pairing" mode.
- Enable Bluetooth® on your Mobile Phone, Tablet, or Computer.
- Scan for available devices and pair with "NAXA NAS-3082".
- If your device requires a password, please enter "0000" to confirm the pairing process.
- You will hear a voice confirming you have paired successfully.
- If pairing was unsuccessful, please repeat the steps above.
Bluetooth® Control Buttons
When the speaker is connected to a device via Bluetooth®:
| To | Action | Do |
|---|---|---|
| Start, Pause, or Resume playback | Press [Play/Pause] / [Call] | |
| Play the previous track | Press [Previous Track] / [Volume Down] | |
| Play the next track | Press [Next Track] / [Volume Up] | |
| Adjust the Volume | Press and Hold [Previous Track] / [Volume Down] or [Next Track] / [Volume Up] |
ℹ️ You may also use your device to control playback. Some devices may not support remote Bluetooth controls. Volume control can be adjusted on both the device and speaker.
| To | Action | Do |
|---|---|---|
| Answer/End Call | Press [Play/Pause] / [Call] | |
| Call previous number dialed | Press [Play/Pause] / [Call] (2x) times quickly |
Listening to FM Radio
- Turn ON the unit.
- Short press the MODE button until you hear the FM Tuner input.
- Short press the [Play/Pause] button for searching and recording preset radio stations within the frequency range of 87.5-108Mhz.
- Short press the [Previous Track] or [Next Track] buttons to listen to the next and previous preset radio stations.
- Long press the [Previous Track] or [Next Track] buttons to adjust the volume up or down.
AUX Mode
Connect devices without Bluetooth® by using the AUX input. A 3.5mm stereo mini patch cable (supplied) is required to make this connection.
- Turn ON the unit.
- Connect your audio device using the supplied 3.5mm AUX cable and the unit will automatically go to the LINE(AUX) input.
- Select your favorite song on your source player and begin playback.
Using USB & Micro SD Mode
Install a USB drive or MicroSD card and music will automatically begin playback.
- Turn ON the unit.
- Insert a USB flash drive or a MicroSD card in the slot and music will automatically begin playback.
- Short press [Previous Track] or [Next Track] to switch between your tracks.
- Short press the Play/Pause button to Pause or resume playback.
- Long press [Previous Track] or [Next Track] to increase or decrease the volume.
If you insert a USB drive or MicroSD card while in Bluetooth® Mode, the unit will disconnect from Bluetooth® and begin playback in USB or MicroSD mode. Press the Mode button to return back to BT.
Connecting Power
Your speaker has an integrated rechargeable battery. Upon initial use, the battery should be fully charged to ensure optimal performance and battery life.
Use the included USB charging cable to connect the speaker to a USB power source to charge the battery.
- Connect the USB charging cable (included) to a DC 5V charging port of the speaker and insert the other end into a USB port on your computer or a similar power source.
- Red LED indicator signifies that the unit is charging. Once the unit is fully charged, the LED indicator light will turn off.
It takes approximately 3 to 6 hours to charge the unit fully when connected to a standard USB port.
Do not charge the unit for more than 8 hours to optimize the lifetime performance of the battery.
Troubleshooting Guide
This guide lists common problems and their solutions. Please refer to this guide before requesting service. If you need further assistance, please contact Naxa Technical Support @ www.naxa.com/naxa_support/
| Symptom | Possible Cause | Solution |
|---|---|---|
| There is no power. | The power switch is set to Off. | Make sure the switch is set to ON. |
| Battery dead. | Charge the battery. | |
| Device is unable to connect to the speaker. | The speaker is not in pairing mode. | Power cycle the speaker. |
| Bluetooth is disabled. | Enable Bluetooth mode on your device. | |
| The device is connected but there is no sound. | The AUX connector may be in use. | Disconnect the AUX cable from the device. |
| Your device may be too far from the speaker. | Move your device closer to the speaker. | |
| Your device is not in playback mode. | Ensure your device is operating correctly. Start playback. |
Specifications
| Speaker Output | 6W RMS (2 x 3W) |
| Audio Frequency Range | 80Hz – 18,000Hz |
| External Memory Support | USB, Micro SD (max 32GB) |
| Audio Format | MP3 |
| Radio Band | FM |
| Radio Band Coverage | 87.5 - 108 MHz |
| Inputs | Bluetooth®, AUX (3.5mm) |
| Built-in Rechargeable battery | 3.7V / 1500 mAh |
| Battery Life | Talk time: Up to 4 hours; Playback: Up to 1.5 hours |
Accessories
- 1 x Bluetooth Portable Speaker
- 1 x Owner's Manual
- 1 x USB Charging Cable
- 1 x 3.5 mm AUX cable
Specifications are subject to change without prior notice.
Support
If you have problems with your device, please review the instructions in this manual. Please also visit us on the web at www.naxa.com to get the latest news, alerts, and documentation for your device. For additional assistance, please contact Naxa Technical Support.
NAXA Technical Support
2320 East 49th St.
Vernon, CA 90058
866-411-6292
http://www.naxa.com/naxa_support/
MADE IN CHINA
Model: NAS-3082 v1.1
