Contact Information
Contact us if you have any questions:
- ✉️ Email: Belifehome@outlook.com
- ? Phone: 401-300-0032 (9AM-5PM CDT WEEKDAY)
Assembly and Operation
Assembly as shown below
Align the main body, extension rod, and the cleaning tool as shown and insert until they "click". To remove any attachments/accessories, press and hold the button, and pull to remove.
Diagram Description: An illustration shows the main body, extension rod, and cleaning tool of a vacuum cleaner being connected. A button is highlighted, indicating its function for detaching accessories.
Note: All attachments included are compatible with the main body and the extension rod.
Insert Battery
Slide the battery into the slot rail to load it.
Diagram Description: An illustration depicts a battery being slid into a slot on the main body of the vacuum cleaner. The slot is labeled.
Turn on the Vacuum Cleaner
1. Pull the ON/OFF trigger to turn on.
2. Pull the same trigger to turn off.
Diagram Description: A close-up view of the vacuum cleaner's handle shows the ON/OFF trigger. Another part of the diagram indicates a suction level selector with multiple indicator lights.
Troubleshooting
Digital Display Panel
The digital display panel provides indicators for various issues:
- Suction blockage indicator: Alerts when suction is obstructed.
- Brush stuck indicator: Alerts when the brush is jammed.
- Whole screen indicators are on: May indicate a voltage problem.
- Voltage problem: Indicates a potential issue with the battery.
Problem Table:
| Display Indicator | Problem | Suggested Solutions |
|---|---|---|
| Suction blockage | Suction blockage | Clean filter regularly. Remove hair and foreign objects from the brush, bearing, floor brush, extension rod, main body air inlet, and dirt bin. Refer to the maintenance section in the instruction manual. Ensure HEPA filters are clean and free from blockage. |
| Brush stuck | Brush stuck | Remove any foreign objects causing the brush to stop automatically. If no foreign object is found, restart the vacuum. |
| Voltage problem | Voltage problem | This problem is caused by a defective battery. Please contact customer service for battery replacement. |
| Screen not light up after a few seconds when fully charged | Screen not light up | This problem is caused by a defective battery. Please contact customer service for battery replacement. |
Note: If you have any other questions, please contact customer service.
Mode Suggested
The vacuum cleaner offers different modes for various cleaning needs:
| Mode | Runtime | Suitable For |
|---|---|---|
| Eco Mode | 40 min runtime | Hair and dust on wood floor or tile. |
| Normal Mode | 30 min runtime | Fine dust and hair on low pile carpet. |
| Hyper Mode | 10-15 min runtime | Dog food, coffee beans, and other large particles on low pile carpet. |
Maintenance
One Click Empty
Cleaning frequency: After every use.
Maintain a 90° vertical operation; otherwise, the dust cup cannot be opened.
Diagram Description: An illustration shows the dust cup of the vacuum cleaner, with a rubber band visible. The first step shows a hand pulling a ring to empty trash into the cup.
Cleaning the Cyclone Unit
Cleaning frequency: Whenever needed.
- Pull the pull ring fully.
- Lift the dirt bin.
- Remove the dirt bin.
- Gently pull to separate the cyclone unit from the dirt bin.
- Brush the cyclone unit to remove debris and dust.
- If necessary, wash with tap water.
- Air dry completely (allow 24 hours).
Diagram Description: A series of illustrations detail the steps for cleaning the cyclone unit: pulling a ring, lifting and removing the dirt bin, separating the cyclone unit, brushing it clean, and then washing with tap water and air-drying. An icon indicating 24 hours for drying is shown.
WARNING! Never attempt to disassemble the sealed cyclone unit.
Cleaning the HEPA Filter
Cleaning frequency: 3-6 months or whenever airflow is weak.
- Turn the HEPA filter counter-clockwise to remove it.
- Wash with cold water.
- Dry completely (allow 24 hours).
Diagram Description: Illustrations show the HEPA filter being removed by turning it counter-clockwise, then washed under a tap, and finally air-dried for 24 hours.
Cleaning the Pre-motor Filter
Cleaning frequency: 1-2 months or whenever airflow is weak.
- Remove the HEPA filter first, then gently pull out the pre-motor filter.
- Wash with tap water, hand wash with soap if necessary.
- Dry completely (allow 12 hours).
Diagram Description: Illustrations show the pre-motor filter being removed after the HEPA filter, then washed under a tap, and finally air-dried for 12 hours.
WARNING!
- DO NOT brush any part of the porous filtration material.
- DO NOT soak any filter in water for more than 10 minutes.
- DO NOT wash any other part of the vacuum except the specified filters assembly.
Cleaning the Brush and Bearing
- Pull to release the brush locking clip.
- Remove the brush locking clip.
- Lift the roller from the clip end.
- Remove debris on the two small brush wheels with tweezers.
- Gently pull to remove the brush bearing cap.
- Remove debris on the shaft (metal bearing).
- Apply lubricating oil or "WD40" onto the metal bearing occasionally.
Diagram Description: A sequence of illustrations demonstrates cleaning the brush and bearing: releasing and removing a clip, lifting the brush roller, cleaning small wheels with tweezers, removing the bearing cap, cleaning debris from the shaft (showing a metal bearing), and applying oil to the bearing.
