VARIABLE SPEED PUMP 2.2HP 230V 2 INCH

IMPORTANT SAFETY INSTRUCTIONS

This guide provides instructions for installing and using the VARIABLE SPEED PUMP. If you have any questions about the equipment, please contact XtremepowerUS.

This guide contains important information about safely installing and operating this product. After installation, make sure to share this information with the owner/operator or leave it with them for their reference.

Legends and Symbols

❗ DANGER: Ignoring these hazards can result in death, severe personal injury, or significant property damage.

⚠️ WARNING: Indicates potential hazards that can result in severe personal injury, death, or significant property damage. Ignoring these warnings presents a real danger.

? CAUTION: Indicates potential hazards that can result in minor or moderate personal injury, property damage, or actions that are unpredictable and unsafe. Ignoring these cautions presents a potential hazard.

ℹ️ NOTICE: This label indicates important special instructions that are not directly related to hazards.

ATTENTION INSTALLER: This manual contains vital information regarding the installation, operation, and safe use of this product. It is essential to provide this manual to the end user of the product. Failure to read and follow all instructions could lead to severe injuries.

❗ DANGER: Failure to comply with all instructions and warnings may lead to severe bodily injury or even death. For optimal safety and functionality, it is advisable to have the product installed and serviced by a certified service professional. Prior to using this product, installers, operators, and owners must carefully review these warnings and all instructions provided in the owner's manual. It is essential to leave these warnings and the owner's manual with the owner for their reference and safety.

⚠️ WARNING: For safety reasons, children should not be allowed to use this product. Packing materials and plastic bags are not toys. Keep them away from children to prevent the risk of suffocation.

❗ DANGER - Suction Entrapment Risk: High suction can trap and drown individuals near drains or broken covers. Avoid using the pool or spa if drain covers are missing, cracked, or damaged.

❗ DANGER - Electrical Hazard: Never open the pump's drive or motor enclosure to avoid electrical hazards.

⚠️ WARNING - Qualified Installation: Pool pump installation and servicing should only be performed by a qualified pool service professional.

⚠️ WARNING - Correct Application: Avoid using the pump in settings for which it was not designed, as improper usage can lead to injury or death.

⚠️ WARNING - Adult Supervision: This product is not suitable for use by children without adult supervision.

⚠️ WARNING - Ensure Safe Operation: Only install the pump in applications that match its intended design.

⚠️ WARNING - High-Pressure Hazard: Pool circulation systems operate under high pressure, which can lead to serious injury if improperly handled.

⚠️ WARNING - Start-Up Precautions: Stand clear of the system during start-up to avoid potential hazards from pressure surges.

? CAUTION - System Sizing and Installation: Ensure that pumps are properly sized and installed to avoid injury, system damage, or compromised performance.

? CAUTION - Suction Entrapment Hazard: Stay off the main drain and away from suction outlets. Ensure properly installed and secured anti-entrapment covers are in place to prevent hazards. Maintain distance from main drains and suction outlets. If possible, disable suction outlets or convert them to return inlets. All suction plumbing installations must comply with national and local codes.

ℹ️ NOTE - Intended Use: This pump is for permanent swimming pools and compatible hot tubs or spas. It is not for use with storable pools.

ℹ️ NOTE - Manual and Label Adherence: Review the product manual for important operation and maintenance guidelines.

ℹ️ NOTE - Safe Electrical Setup: Electrical installations must allow for safe operation without exposing users to electrical risks.

ℹ️ NOTE - Safety Labels: Maintain safety labels in good condition for clear visibility of hazards and replaced if damaged.

ℹ️ NOTE - Air Relief: Before starting the system, open the air relief valve and confirm all system valves are open to avoid pressure buildup.

OVERVIEW (PRODUCT INFORMATION)

PRODUCT INTRODUCTION

This pump boasts a variable frequency drive that ensures premium efficiency, allowing for flexible adjustments in motor speed and operation duration. Capable of functioning across a broad speed spectrum of 1000 to 3450 RPM, it is also designed to work with 230 VRMS nominal voltage at both 50HZ and 60HZ frequencies. Engineered to prioritize energy conservation, the pump maintains cleanliness at the lowest necessary speeds, with optimal settings being influenced by pool dimensions, additional water features, sanitation chemicals used, and environmental conditions. Determining the most energy-efficient settings may require a period of trial and optimization.

KEY FEATURES

DRIVE

• User-friendly interface
• Weather-resistant design
• Integrated daily timer
• Adjustable start-up priming
• Programmable Quick Clean function
• Persistent alarm system
• 230V input, compatible with 50/60Hz
• Overload protection circuit
• Clock memory during power cuts

PUMP

• Ultra-quiet operation
• 2-inch connections for straightforward replacement
• Transparent lid for strainer basket monitoring
• Self-priming for fast startup

MOTOR

• High-efficiency, permanent magnet design
• 56 square flange size
• Quiet performance
• Outdoor-rated durability
• Cooler operation through high efficiency
• Surpasses Department of Energy and Energy Star standards
• TEFC (totally enclosed fan-cooled) motor with permanent magnets

SPECIFICATION

DIMENSIONS

Approximate dimensions: Height 22.6 inches (574mm), Width 11.3 inches (288mm), Depth 10.2 inches (258mm). Other measurements include: 13.7" (347mm) length, 10.3" (262mm) width, 6.3" (159mm) depth, 12.9" (328mm) length, 9.1" (232mm) depth, 7.6" (194mm) height, 8.9" (225mm) depth.

INSTALLATION

Installation should be performed only by a qualified plumbing professional to ensure proper setup and to mitigate safety risks. Refer to the IMPORTANT SAFETY INSTRUCTIONS on pages 1-3 for detailed safety and installation guidance.

LOCATION

ℹ️ NOTE: Do not install the pump in an enclosed space, such as an external enclosure or under a hot tub or spa skirt. Ensure that the pump is securely attached to a stable equipment pad for optimal performance.

LOCATION REQUIREMENTS

• Place the pump close to the pool or spa, using short, direct piping for both suction and return lines to reduce friction loss and increase efficiency.
• Maintain a minimum distance of 5 feet from the pool or spa's inner wall (9.8 feet in Canada).
• Keep the pump at least 3 feet away from the heater outlet.
• Avoid placing the pump more than 5 feet above the water level to prevent operational issues.
• Install the pump in a well-ventilated area, away from moisture sources such as rain gutters and sprinklers.
• Leave at least 3 inches of clearance at the rear for motor removal and 5 inches on top for keypad accessibility.

Diagram Description (Figure 1): Shows required clearance around the pump: 3 inches minimum at the rear for motor removal and 5 inches minimum on top for keypad accessibility.

PIPING

PIPING GUIDELINES

• Use larger piping to increase plumbing efficiency, ensuring that the suction side pipe diameter is equal to or larger than that of the return line to facilitate optimal flow.
• Keep the suction side piping as short as possible to enhance pump performance.
• Maintain a straight section of pipe on the suction line that is at least five times the pipe's diameter before the pump's inlet. This setup improves priming speed and extends the lifespan of the pump by reducing turbulence.

Diagram Description (Figure 2): Illustrates optimal piping setup. It shows a straight section of pipe at least five times the suction pipe's diameter before the pump's inlet to reduce turbulence and improve priming. Avoid placing 90° elbows directly at the suction port.

FITTINGS AND VALVES

ℹ️ NOTE: To reduce turbulence and prevent cavitation, avoid placing 90° elbows directly at the pump's suction port.

• For flooded suction systems, install gate valves on both the suction and discharge pipes to allow for easy isolation during maintenance.
• Position the suction gate valve at least five times the suction pipe's diameter away from the pump to prevent interference with flow dynamics.
• Install a check valve on the discharge line, especially if the plumbing has a significant rise after the pump, to prevent water backflow and help maintain consistent pump performance.
• When plumbing two pumps in parallel, install check valves on each pump's discharge line to prevent reverse rotation of the impeller and motor, which can occur if one pump is running while the other is off or during fluctuations in flow.

ELECTRICAL INSTALLATION

⚠️ WARNING: Risk of Electrical Shock or Electrocution: It is strongly recommended that a certified electrician or qualified professional install this pump in accordance with the National Electrical Code and local regulations to mitigate the risk of serious injury, death, or property damage. Always disconnect power at the circuit breaker before servicing to prevent electric shock or injury. Read all instructions carefully before servicing the pump.

ℹ️ NOTE: The pump is designed to operate with a 230 V single-phase input, compatible with both 50 and 60 Hz. Its power connections support up to 8 AWG solid or stranded wire.

WIRING INSTRUCTIONS

• Turn off all breakers and switches before beginning motor wiring.
• Verify that the supply voltage matches the motor's nameplate specifications.
• Adhere to the National Electrical Code and local codes for wire sizes and requirements; select a heavier gauge wire if uncertain.
• Ensure all electrical connections are secure and free of corrosion. Trim wires to fit terminals precisely, avoiding excess overlap or contact.
• Always replace the drive lid after completing wiring or when leaving the pump unattended to protect it from the elements.

ℹ️ NOTE: Take care not to pinch wires when securing the drive body and lid.

GROUNDING INSTRUCTIONS

Ensure the motor is permanently grounded using the Grounding Terminal located in the drive's wiring compartment. Comply with the National Electrical Code and local regulations regarding the grounding wire's size and type. Attach the ground wire to the electrical service's ground.

BONDING INSTRUCTIONS

Connect the motor to the pool's structural metal components, electrical systems, and metal conduits and piping within 5 feet of the pool or spa's inner walls using the provided bonding lug on the motor's side. Comply with the current National Electrical Code and local codes for bonding practices. A solid copper conductor of at least 8 AWG is required for bonding. For installations in Canada, a 6 AWG or thicker solid copper conductor is necessary.

Diagram Description (Figure 3): Shows electrical connections. L1/L and L2/N terminals for power input, and a GND terminal for grounding. It also indicates a bonding lug on the motor's side for connecting to pool's structural metal components.

OPERATION

INITIAL SETUP

Before initial use of the pump, program its internal clock and operational schedules. Instructions for setting the clock are available under SETTING THE CLOCK and USING THE DEFAULT SCHEDULE. For custom schedule programming, see CUSTOM SCHEDULE PROGRAMMING.

The drive keypad allows programming and control of the pump and provides access to all features and settings.

ℹ️ NOTE: The pump's functionality may vary if features like External Control Only Mode or Keypad Lockout are enabled.

? CAUTION: To avoid damaging the keypad, use only your fingers to press the buttons; do not use screwdrivers, pens, or other tools for programming the pump.

⚠️ WARNING: If the pump motor is connected to power, pressing any buttons mentioned in this section may activate the motor. Unexpected motor start-ups could result in personal injury or equipment damage. Always be aware of the motor's power status when programming or servicing.

KEYPAD FUNCTIONS

Diagram Description (Figure 4): Depicts the pump's control keypad. It includes numbered speed buttons (1-4), a Quick Clean button, Start/Stop button, Main Menu Access button, Display button, Arrow Keys (Up, Down, Left), a Digital Display, Display Mode LED Indicator, and Power LED Indicator. Each button's function is described:

• SPEED 1-4: Buttons to activate specific speeds (e.g., 2850 RPM for Speed 1, 1150 RPM for Speed 4). Corresponding LEDs illuminate.
• QUICK CLEAN KEY: Dedicated button for the Quick Clean function.
• START / STOP KEY: Press to start or stop the pump. A lit indicator signifies operation; a blinking indicator shows the pump is off and awaiting the next scheduled mode.
• MAIN MENU ACCESS: Press to enter the main menu directory when the frequency converter is powered down.
• DISPLAY BUTTON: Press to switch between different display contents during pump operation.
• ARROW KEYS: UP/DOWN to increase/decrease speed or time; LEFT to move the cursor.
• CONTROL PANEL DIGITAL DISPLAY: Shows operational parameters like current speed, time, duration, power consumption, Bluetooth status, etc.
• DISPLAY MODE LED INDICATOR: Works with the display button; lights up to match display info. A blinking LED indicates the parameter can be edited.
• POWER LED INDICATOR: Illuminated LED indicates the pump is powered and receiving energy.

INITIAL PROGRAMMING

Before first use, set the pump's internal clock and operational schedules. Ensure that the start times for Speeds 1 through 4 are programmed in chronological order within a 24-hour period.

SETTING THE CLOCK

When the pump is first connected to power, the clock will flash, indicating the need for setup. Press 'Setting'. Use the '+' and '-' buttons to set the current time, and '<' and '>' to adjust the cursor position. AM/PM will be displayed in 12-hour format.

USING THE DEFAULT SCHEDULE

The default schedule provides adequate daily circulation for most pools. The default operating cycle runs for 22 hours per day.

Default Schedule Operation: SPEED 1 starts at 8:00 AM for 2 hours. SPEED 2 starts at 10:00 AM for 10 hours. SPEED 3 starts at 8:00 PM for 2 hours. SPEED 4 starts at 10:00 PM for 8 hours. Following SPEED 4, the pump pauses for 2 hours and then resumes with SPEED 1. This cycle repeats, maintaining a 22-hour daily operation.

ℹ️ NOTE: To start the pump, press the Start/Stop button and ensure that the corresponding LED is illuminated.

CUSTOM SCHEDULE PROGRAMMING

Ensure the pump is halted (Start/Stop LED off) before customizing. A blinking LED next to a parameter indicates it is in programming mode.

1. Press Start/Stop to stop the pump.
2. Press '1' to edit Speed 1; its LED and 'Speed' will blink. Adjust the Speed 1 RPM using the '+' and '-' buttons, and move the cursor with '<' and '>'. Speed adjusts in 100/10/1 RPM increments.
3. Press '1' again to set the start time for Speed 1; 'Time' will blink. Set the start time with '+' and '-' buttons, adjusting the cursor with '<' and '>'. Adjust time in increments of 1 hour/10 minutes/1 minute.
4. Press '1' again to set the duration for Speed 1; 'Duration' will blink. Set the duration using '+' and '-' buttons, and adjust the cursor with '<' and '>'. Duration adjusts in increments of 1 hour and 10 minutes. If set to 0, the pump will skip this segment.
5. Confirm Speed 1 setup. Subsequent presses of '1' cycle through settings, saving changes automatically.
6. To set Speed 2, press '2' and follow the same steps as for Speed 1 (adjust RPM, time, duration).
7. Follow steps for Speed 2 to set Speed 3 and Speed 4.
8. To set Quick Clean settings, follow similar steps using the Quick Clean button.
9. To activate the pump with the new schedule, press Start/Stop; the LED will light up. If the pump was manually stopped, press Start/Stop again to start the schedule. A lit Start/Stop LED indicates the pump will follow the set schedule.

SPEED PRIORITIZATION FOR SCHEDULING (WITHOUT EXTERNAL CONTROL)

When operating based on the internal schedule, programmed speeds follow a priority sequence from highest to lowest: SPEED 1, SPEED 2, SPEED 3, and SPEED 4. The prioritization order ensures that if timeframes overlap, the higher priority speed takes precedence.

Example: If SPEED 1 is scheduled from 8:00 AM to 2:00 PM, and SPEED 2 is scheduled from 9:00 AM to 10:00 AM, the pump will run in SPEED 1 mode from 8:00 AM to 2:00 PM, effectively skipping the scheduled time for SPEED 2 because it falls within the SPEED 1 period.

OPERATING THE PUMP IN ACTIVE MODE

? CAUTION: When the pump is powered, pressing any button may activate the motor, potentially causing personal injury or equipment damage. Always be aware of the motor's power status.

The Display button toggles through active settings: SPEED (current RPM), TIME (current time), DURATION (time left at current speed), and WATTS (current power usage). Pressing any Speed button (1, 2, 3, 4, or Quick Clean) during operation temporarily overrides the current setting. The pump will run at the selected speed for the preset duration, then resume the regular schedule. Changes made during operation apply only for the remaining duration of the active program and do not permanently save.

PROGRAMMING QUICK CLEAN

The pump includes a Quick Clean option for temporary operation at speeds ranging from 1700 to 3450 RPM. After a Quick Clean cycle, the pump reverts to its scheduled program.

1. Stop the pump by pressing Start/Stop. Activate Quick Clean mode; the Quick Clean and 'Speed' LEDs will flash.
2. Set the RPM using the '+' and '-' keys, and navigate with '<' and '>'. RPM can be adjusted in increments of 100, 10, or 1 RPM.
3. Press Quick Clean again to set the duration; the 'Duration' LED will blink.
4. Adjust the duration in hours and minutes using '+' and '-' keys, and navigate with '<' and '>'. Duration adjustments are available in increments of 1 hour or 10 minutes, with a range from 10 minutes to 24 hours. The Quick Clean duration setting will not affect the programmed start time of the regular schedule.

FACTORY RESET

To revert the drive to its default settings, perform a Factory Reset. This action erases all customized settings and schedules except for the current time of day. Confirm the necessity of this action before proceeding, as the reset takes immediate effect.

FACTORY RESET PROCESS

• Stop the pump by pressing the Start/Stop button if it is currently running.
• Hold down the "1" and "2" buttons simultaneously for 3 seconds.
• A prompt tone lasting 3 seconds will confirm a successful reset. After the reset, reprogram the schedule and priming speed as outlined in previous sections. To activate the pump for subsequent operation, press the Start/Stop button; the pump will then follow the newly set schedule.

PRIMING

? CAUTION: The pump is pre-set to Priming mode, which causes it to automatically accelerate to 3200 RPM upon initial start-up.

Before activating the pump:

• Open the filter's air relief valve.
• Ensure that all necessary valves are open.
• Confirm that the return line is unobstructed.
• Fill the pump with water.
• Maintain a safe distance from the filter and any pressurized vessels.

⚠️ WARNING: Never run the pump dry, as it will damage the shaft seal and cause leaks. Replace any damaged seal immediately. Maintain the proper water level in your pool (at least halfway up the skimmer opening) to prevent air from being drawn through the skimmer. A low water level can cause the pump to lose its prime, potentially leading to seal damage. Continuous operation with a compromised seal can damage the pump body and impeller, and may lead to personal injury and property damage.

STARTUP AND PRIMING PROCESS

At startup, the pump automatically begins a priming cycle, separate from any Quick Clean cycle. It starts at 2400 RPM and gradually increases to 3200 RPM over 5 minutes, with the drive displaying the time remaining.

ℹ️ NOTE: If the control system's priming timer is still running after the priming cycle, the pump will continue at the control system's set speed until the timer expires. The startup speed can be adjusted between 3200 RPM and 3450 RPM using the '+' and '-' buttons during boot-up.

ℹ️ NOTE: The initial boot begins with a 5-minute countdown. Press any Speed button (1 to 4) to exit the priming mode prematurely. Upon subsequent startups, the pump will assess the need for priming, taking approximately 20 seconds to determine if priming is required.

Priming duration may vary with local conditions, such as water temperature, atmospheric pressure, and pool water level. Test and adjust priming speeds as needed, allowing the system to drain between tests.

ℹ️ NOTE: To avoid air intake into the system, ensure the pump strainer pot is filled with water up to the bottom of the suction port.

MAINTENANCE

⚠️ WARNING - STRAINER POT HANDLING: Never open the strainer pot if the pump has failed to prime or has operated without water, as vapor pressure build-up may cause scalding water inside. Opening under these conditions can lead to severe injury. Ensure both suction and discharge valves are open, and verify that the strainer pot is cool before cautiously opening it.

⚠️ WARNING - POWER DISCONNECTION: Always turn off power at the circuit breaker and disconnect the digital input cable before servicing the pump. Failing to do so may result in fatal or severe electric shock injuries. Read and understand all service instructions prior to performing pump maintenance.

? CAUTION - PUMP MAINTENANCE: To prevent pump damage and maintain system efficiency, regularly clean the pump strainer and skimmer baskets.

CLEANING THE PUMP STRAINER BASKET

The strainer pot, located at the front of the pump, contains the strainer basket. Inspect the basket through the pot lid visually at least once a week. Regular cleaning ensures higher efficiency of the filter and heater and reduces stress on the pump motor.

CLEANING INSTRUCTIONS

• Stop the pump by pressing Start/Stop, and turn off electrical power at the circuit breaker.
• Open the filter's air relief valve to release any pressure in the filtration system.
• Unscrew the strainer pot lid counterclockwise and remove it.
• Remove the basket, clear debris, and rinse it. Replace the basket if it is cracked or damaged.
• Reinsert the basket into the pot, ensuring the basket's notch aligns with the strainer pot's rib.
• Refill the strainer pot with water to the level of the inlet port.
• Clean the lid's O-ring and the pot's sealing surface.

ℹ️ NOTE: Keep the O-ring clean and lubricated.

• Replace the lid, screwing it clockwise until the handles are aligned horizontally.

ℹ️ NOTE: Ensure the O-ring is correctly placed to avoid pinching.

ℹ️ NOTE: Ensure the "Front" label on the lid faces the front of the pump.

• Open the filter air relief valve again and maintain a safe distance from the filter.
• Restore electrical power at the circuit breaker and restart the pump.
• Once a steady water flow is established from the air relief valve, close the valve.

MOTOR CARE

HEAT PROTECTION

• Shield the motor from direct sunlight, ensuring that any covering provides adequate ventilation to prevent overheating.
• Facilitate cross ventilation around the motor area.

DIRT PROTECTION

• Keep foreign materials away from the motor to avoid contamination.
• Store chemicals at a safe distance from the motor to prevent accidental spills.
• Minimize dust generation near the motor during operation, as dirt damage can void the motor warranty.
• Regularly clean the lid, O-ring, and the sealing surface of the strainer pot to maintain optimal performance.

MOISTURE PROTECTION

• Protect the motor from water splashes or sprays, and shield it from harsh weather conditions.
• If the motor becomes wet internally, allow it to dry thoroughly before use.
• Do not operate a flooded pump, as water damage can void the motor warranty.

⚠️ WARNING: HIGH-PRESSURE SYSTEM OPERATION: This system operates under high pressure, so servicing any component in the circulation system can introduce air, leading to pressurization. Such pressurized air may forcefully dislodge the lid, posing serious risks of injury, death, or property damage. To prevent these hazards, follow all provided instructions closely.

PUMP DISASSEMBLY AND REASSEMBLY

ℹ️ NOTE: For a detailed parts breakdown, refer to the REPLACEMENT PARTS section.

⚠️ WARNING - POWER DISCONNECTION: It is crucial to always shut off power at the circuit breaker before servicing the pump. Failing to disconnect the power source can result in potentially fatal electric shock injuries. Ensure you fully understand and comply with all servicing guidelines before beginning any maintenance work.

⚠️ WARNING - STRAINER POT HANDLING: Do not open the strainer pot if the pump is having trouble priming or has been operating without water, as these conditions can cause vapor pressure build-up with extremely hot water inside, posing a serious risk if opened. For safety, confirm that both the suction and discharge valves are open and that the strainer pot is cool to the touch before attempting to open it. Proceed with extreme caution.

REQUIRED TOOLS

• Adjustable wrench
• #2 Phillips screwdriver
• Flat blade screwdriver

PUMP DISASSEMBLY

• Stop the pump using the Start/Stop button and disconnect power at the circuit breaker.
• Unplug digital inputs or communication cables, if present.
• Close all valves on the suction and discharge lines.
• Release system pressure using the filter's air relief valve.
• Remove the drain plugs from the bottom of the strainer pot.
• Unscrew the two through-bolts and nuts of the strainer pot using an adjustable wrench.
• Remove the four remaining strainer pot bolts.
• Detach the motor/hydraulics assembly from the strainer pot carefully.
• Unscrew the diffuser from the seal plate.
• Hold the motor shaft at the motor's rear to prevent it from spinning. Remove the impeller screw and washer.
• Unscrew the impeller by hand.
• Remove the four bolts from the seal plate using a 9/16 inch wrench.
• Take off the seal plate from the motor/drive assembly.

PUMP REASSEMBLY

• Align the seal plate on the motor, ensuring the "UP" marking is at the top.
• Attach the seal plate to the motor with bolts, tightening to 70-80 in-lbs.
• Hold the motor shaft and reattach the impeller to the shaft, followed by the impeller screw and washer; tighten to 25 in-lbs.

ℹ️ NOTE: The impeller screw has reverse threading.

• Reinstall the diffuser onto the seal plate and secure with screws. Replace the diffuser seal and seal plate gasket if necessary, applying lubrication as needed.
• Reattach the strainer pot to the motor/hydraulics assembly with bolts and washers.

ℹ️ NOTE: Tighten the through-bolts only after all bolts are finger-tightened, then secure to 110 in-lbs.

ℹ️ NOTE: Ensure the seal plate gasket is properly aligned.

• Replace the drain plugs in the strainer pot.
• Refer to the Pump Restarting section for further instructions on restarting the pump.

PUMP RESTARTING

? CAUTION - Avoiding Dry Running: Never operate the pump without water, as dry running can damage the shaft seal, requiring immediate replacement. Maintain the proper water level in the pool, ideally at least halfway up the skimmer opening, to prevent air intake through the skimmer. A low water level can cause the pump to lose prime, leading to decreased pressure, potential pump damage, property damage, or even personal injury.

PUMP RESTARTING PREPARATION

If the pump is installed below the pool's water level, close the return and suction line valves before opening the strainer pot. Ensure these valves are reopened before starting the pump.

PUMP RESTARTING INSTRUCTIONS

• Stop the pump using the Start/Stop button and disconnect power at the circuit breaker.
• Release all pressure in the filtration system by opening the filter's air relief valve.
• Unscrew and remove the strainer pot lid by turning it counterclockwise.
• Fill the strainer pot with water up to the level of the inlet port.
• Replace the lid onto the strainer pot, securing it by turning clockwise.

ℹ️ NOTE: The lid is correctly locked when its handles are nearly perpendicular to the pump body.

• Restore power to the pump at the circuit breaker.
• Open the filter's air relief valve and stand back from the filter.
• Restart the pump using the Start/Stop button.
• Bleed air through the filter air relief valve until water flows steadily, then close the valve.

WINTERIZING

Be proactive in anticipating freezing conditions, as freeze damage is not covered under warranty. In areas with mild climates where temporary freezing may occur, keep the filtering equipment running overnight to prevent freezing.

PREVENT FREEZE DAMAGE INSTRUCTIONS

• Stop the pump by pressing Start/Stop and disconnect all power at the circuit breaker. Confirm that all power sources are disconnected.
• Release pressure from the filtration system using the filter's air relief valve.
• Remove both drain plugs at the bottom of the strainer pot to drain the pump completely. Store the plugs in the strainer basket for safekeeping.
• Protect the motor by covering it to shield it from heavy rain, snow, and ice.

ℹ️ NOTE: Avoid using plastic or airtight materials to cover the motor during winter storage. Ensure the motor remains uncovered if it will be operational or if the pump is expected to run.

TROUBLESHOOTING

⚠️ WARNING: ELECTRICAL SAFETY: Risk of Electrical Exposure: Diagnosis may require proximity to live components. Servicing should only be performed by certified professionals to prevent serious risks, including death, personal injury, or property damage.

ALARMS AND FAULT CODE GUIDANCE

When an alarm triggers, the drive will halt the pump and display a fault code. To reset, turn off the power and wait for all keypad LEDs to go off before restoring power. If the fault persists, consult the error description table below for troubleshooting.

FAULT CODE DESCRIPTIONS

• 1: Obstruction, motor wiring issue, short circuit, or excessive temperature rise.
• 2, 4, 6: Input voltage is too high.
• 8: Input voltage is too low.
• 16, 128: Motor does not start under normal conditions.
• 256: Motor phase loss or poor connection between motor and driver.
• 300: Pump running without water (no load).
• 301: Overheating of internal components.

SPECIFIC FAULTS

• Power Out Failure: Supply voltage drops below 190 VAC, or the controller's input voltage exceeds the limit.
• 16, 128 - Motor Failure to Start: May result from a jammed motor, improperly connected ground wire, or incorrect driver installation.
• 300 - No Load: Indicates the pump may not be drawing water.
• 301 - Over-temperature: Internal driver components have exceeded their temperature limit.

REPLACEMENT PARTS

The following is a list of common replacement parts for the 75409 Variable Speed Pump, referencing a parts diagram.

• COVER (Part No. 47276502)
• O-RING 145* 5 (Part No. 65431042080)
• BASKET (Part No. 647276803001)
• PUMP HOUSING (Part No. 47276801)
• O-RING 85.32* 3.53 (Part No. 65431032080)
• SCREW ST4.2*38 (Part No. 65212025000)
• DIFFUSER (Part No. 647254703)
• IMPELLER FOR 75409 (Part No. 647277071000)
• O-RING 196.22* 5.33 (Part No. 65431045080)
• PUMP COVER GASKET (Part No. 647276802)
• M10 SCREW 3/8-16*1 1/2 UNC (Part No. 65244015000)
• SEAL ASSEMBLY (Part No. 65028014000)
• SCREW M10*25 (Part No. 65221008000)
• O-RING 145* 5 (Part No. 65431042080)
• 2.2HP MOTOR FOR 75409 (Part No. 65023556000)
• SUPPORTING FOOT (Part No. 647255302)
• GASKET 19* 13* 1.57 (Part No. 647255503080)
• DRAIN PLUG (Part No. 648860105)
• SPRING WASHER M10 (Part No. 65244032000)
• GASKET 77* 59.5* 3 (Part No. 65432096080)
• 2" TO 1.5" ADAPTOR (Part No. 647255503080)
• 2" ADAPTOR (Part No. 649130101001)
• 2" NUT ADAPTOR (Part No. 649130102001)

DISCLAIMER

The manufacturer and/or distributor have provided the parts list and assembly diagram in this manual for reference purposes only. They do not make any representation or warranty to the buyer that they are qualified to make repairs to the product or replace any parts of the product. In fact, the manufacturer and/or distributor expressly state that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising from their repairs to the original product or replacement parts or arising from their installation of replacement parts. It is strongly advised that qualified professionals handle any repairs or replacements to ensure safety and proper functioning of the product. Improper installation and operation may result in injury, property damage, or voiding of warranty. The manufacturer and/or distributor shall not be held responsible for any accidents, damages, or malfunctions resulting from the buyer's installation and operation of the product. It is essential to follow all safety guidelines and recommendations provided in this manual and to seek professional assistance if unsure about the installation or operation procedures.

CUSTOMER SERVICE AND TECHNICAL SUPPORT

If you have any questions about ordering pool pumps and replacement parts or pool products, please feel free to contact XtremepowerUS using the following contact information:

Phone: (909) 628-0880

Email: customer@xtremepowerusa.com

Hours of Operation: Monday – Friday, 9AM – 4PM (CST)