User Manual for ZKTeco models including: PE082120C Switch 8 Puertos PoE Fast Ethernet, PE082120C, Switch 8 Puertos PoE Fast Ethernet, Puertos PoE Fast Ethernet, PoE Fast Ethernet, Fast Ethernet, Ethernet
PE082120C Switch 8 puertos PoE Fast Ethernet
PE04155C Switch 4 puertos PoE hasta 250mts con cable CAT6
PE162200C Switch 16 puertos 10/100Mbps PoE estándar af/at
File Info : application/pdf, 1 Pages, 2.27MB
DocumentDocument7.Indicator Definition De nition PWR Indicator Power Indicator SYS System Indicator PoE PoE Indicator 1000M Link Rate 100M Link Rate Link/ACT Link & Date Mode/SW Loop Dial Switch Indicator Loop Alarm State Light on Light off Light on Flash Light on Light off Light on Light off Light on Light off Light on Flash Light on Flash Light off Light on Description Powered Abnormal System Normal System Starting PoE Powered No PoE Powered Gigabit 10/100M 100M Link Disconnect Link is Normal Date Transmission VLAN Extend Default Port Loop 8.PoE Powered Function This function is applicable to PoE switches, not applicable to non-PoE switches. Standard PoE Power Supply ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 Fax : +86 755 - 89602394 www.zkteco.com Copyright ® 2021 ZKTECO CO., LTD. All Rights Reserved. PoE Switch 12/36 is the power supply and data pin Passive PoE Power Supply PoE Camera Passive PoE Switch 12/36 is the data pin 45/78 is the power supply pin Intercom System 5 1.Description The products described in this manual, including but not limited to the illustrated products, please refer to the actual product purchased. If any changes on product appearance, please refer to the official product information. Management switch connect and login methods are basically the same, this manual only introduces one of them. PoE switch and ethernet switch installation methods are the same, the actual use environment and method that depends on the specific product requirement. 2.Packing List Switch (Specific model See the product label for more details). Power Cable (The default is pluggable or a power cable with built-in power module). Power Adapter (Use for some external power products). Console Cable, Configurable Disc (Use for managed products). Brackets, Screw (Rack type standard, desktop type optional). User manual, Certification. 3.Installation Precaution Do not install the equipment in the environment of seepage, drip or condensation easily, otherwise the equipment might burn out. Please ensure the environment where the equipment is installed is well ventilated, and forbidden to block the cooling holes. Do not install the equipment in a high density dust environment. If rack switches are in a natural heat dissipation environment, please ensure the separation distance exceeds 1U. Do not aerial cabling outdoor, otherwise the equipment is prone to lightning strike. Using temperature and humidity depend on the descriptions of the specific product. 4.Safety Precautions Do not look directly at the optical port to prevent the laser beam from burning your eyes. Do not install the power cord with power on to avoid personal injury. Do not supply power before equipment installation and wiring. ESD protection is necessary during the installation and maintenance of equipment. Do not place objects on the device. 1 2 1. Standard PoE power supply includes: protocol detection, power pin sequence detection, power output, abnormal protection, Link abnormal monitoring. 2. The PoE power supply protocol includes: IEEE802.3af (15.4W), IEEE802.3at (30W), IEEE802.3bt (90W). 3. The standard PoE power pin sequence is 12+/36-, and the passive PoE power pin sequence is 45+/78-. 4. The standard POE switches can automatically detect and supply power to the PDs that meet the standard, non-POE devices are not powered and only transmit data. 5. Passive PoE switches use mandatory power supply mode, non-PoE powered devices may be burned out, please use with caution. 6. 24V POE switches have both low-voltage power supply and PD detection technology, which can provide 24V voltage on 45/78 pin, even if it is connected to non-standard equipment, it will not burn out. 9.States of Switch Function De nition VLAN Port Isolation Extend Default Link Extension Normal Mode Reset Reset Button AI PoE Max PoE Watchdog Power Display Indicator State Light on Flash Light off Flash / Green Yellow Orange Red 6 Description Designated port can not communicate with each other Designated port link extended to 250 meters All ports can communicate with each other Short press restart, long press more than 5 seconds reset configuration PDs crashed and restart automatically PoE Power output25% PoE Power output50% PoE Power output75% PoE Power output75% User Manual Commercial Series Switches Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual. 5.Switch Installation Switches support a variety of installation methods, desktop, wall mounted, rack mount, please install according to the actual environmental requirements. Mounting Ear Installation 5/8 Port 15/24 Port Rack Mount Installation Wall Mounted 1U Rack M6 Screw 1. Install 4 floating screws on the front hole bar of the cabinet, 2 on each side. 2. Load the equipment into the cabinet. 3. Use M6 screws to secure the equipment with the cabinet/rack. 4. Install earth wire to earth connection point. 6.Connecting Equipment Network Cable 1. When the RJ45 port is on 2.5GE rate, use Cat5E and above network cable. 2. When the RJ45 port is on 5GE rate, a shielded network cable of Cat5E and above specifications is required, the unshielded network cable is not recommended. 3. When the RJ45 port is on 10GE rate, shielded network cable of Cat6A and above specifications is required. Grounding Ensure that the grounding screw of the equipment is effectively grounded to protect the safety of the equipment. Optical Fiber 1. Optical fibers must be used with the optical modules. 2. Fiber bending radius must not be less than 40 mm. Power Cable 1. Distance between power cable and nework cable shoule be more than 10cm. 2. The AC power please use the local AC power cable. 3. The DC power please pay attention to the positive and negative electrodes. Console, USB 1. Some switches provide USB interfaces for uploading and downloading configuration files to achieve rapid configuration. 2. The console interface needs to use the serial line in the package to realize the serial port management. Computer Wireless AP Camera Switch Serial Management USB Flash Disk 3 4