iDatalink - Home
Installation Guide for FIRSTECH models including: DL-SUB9, CM7000-7200, CM-X, FTI-STK1 Crosstrek STD KEY AT, FTI-STK1, Crosstrek STD KEY AT, STD KEY AT, KEY AT, AT
Index of /wp-content/uploads/2023/07
FTI-STK1 | MyFirstech Install
File Info : application/pdf, 3 Pages, 345.28KB
DocumentDocumentFTI-STK1: Vehicle Coverage and Preparation Notes Make Model Year Install CAN IMMO BCM Clutch I/O Changes DL-SUB9 Subaru Crosstrek STD KEY AT (Canada) 2024 Type Type 1 20-Pin B DSD Green White/Blue N/A N/A Covered vehicle use BLADE-AL-SUB9 firmware and the following required accessories, Weblink Hub & ACC RFID1. Flash module, and update the controller firmware. Please follow the directions for RFID programming before attempting to program the BLADE module to the vehicle. CAN: Type 1 CAN connections are made using the 20-Pin BCM adapter and require connecting the white 2-pin connectors at marker [D] of the illustration. Immobilizer: Type B IMMO requires connecting the black and white 2-pin connectors at marker [C] of the illustration. Lights: Parking lights are pre-wired in the FTI-STK1 harness. Replace the green/white wire of the CM I/O connector with the pre-terminated green/white wire of the harness. ACC-RFID1 (REQUIRED): SUB9 firmware does not provide immobilizer data, an ACC-RFID1 is therefore required for remote start 2nd START: The FTI-STK1 harness is pre-wired with a red/black 2nd START output (not required in TYPE 1), cut and insulate the provided wire to prevent short circuits when not used. I/O Changes: None required Advisory 1: Program ACC-RFID1 before attempting to program the BLADE module to the vehicle. Advisory 2: Secure all 2-pin connections, both used and unused, to the main harness body. FTI-STK1: Installation and Configuration Notes A REQUIRED ACCESSORY B ADAPTER REQUIRED C REQUIRED CONFIGURATION (TYPE B IMMO) D NO CONNECTION E NO CONNECTION CM7000/7200 Cut loop for A/T CMX CM7X00 CM-X IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII D LAN 2001 O O Z K E R E D st. E IIIIIIIII S ID D KO O rG fo AD E R R E 'T T AN NC CE AND WHO O H W WANNA LEARN TO FEATURE COVERAGE CCMMX 9H0ig0hACSur/r9e0nt0PSroJgurammmpaebrle (+) Output Channels HCP #1 - Parking Light HCP #2 - Accessory HCP #3 - Ignition [ 2 ] 2ND START [ 3 ] 2ND IGNITION [ 4 ] 2ND ACCESSORY CM-900S/900AS IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D O OTHER STUFF GOOD TOO IMMOBILIZER DATA ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE TACH OUTPUT DOOR STATUS TRUNK STATUS BRAKE STATUS E-BRAKE STATUS A/M ALRM CONTROL FROM OEM REMOTE A/M RS CONTROL FROM OEM REMOTE AUTOLIGHT CTRL CM -900 FTI-STK1 - AL-SUB9 - Type 1 2024 Subaru Crosstrek STD KEY(CA) BLADE PWR Notice: Ground Connection Required A 1 4 1 2 16 E Ignition Switch Assembly 1 ACC ON LOCK C D BCM/Fuse Box WHITE 2 20 1 40 21 BCM/FUSEBOX DRIVER SIDE DASH GRAY 10 1 20 11 REAR VIEW B LED Programming Error Codes Module LED flashing RED during programming 1x RED = Unable to communicate with RFID or immobilizer data. 2x RED = No CAN activity. Check the CAN wire connections. 3x RED = No ignition detected. Check the ignition wire connection and CAN. 4x RED = Required ignition output diode not detected. INSTALL GUIDE COM-BLADE-AL(AL)-SUB9-EN 1 Slide cartridge into unit. Notice button under LED. 2 ALL IN ONE SUBARU Doc. No.: ##82344## Ready for Module Programming Procedure. 1 For this installation, the Weblink HUB is required. 2 Remove OEM key 1 from keychain. Place all other keyfobs at least 1 foot away from the Weblink HUB. Failure to comply may result in damage to other keyfobs or interfere with the keyfob reading process. 3 Flash the module using the Weblink HUB. Follow the on screen instructions to complete the keyfob reading process. 4 5 ON 6 WARNING: Do not press the module programming button. Connect power first. Connect module to vehicle. Using OEM key 1, turn key to ON position. Wait, LED will turn solid BLUE for 2 seconds. 7 OFF Turn key to OFF position. 8 Module Programming Procedure completed. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020