About This Instruction Manual
This user manual is an integral part of the device. Before using the device, please read the safety instructions and the user manual carefully. Keep this manual for future reference. If the device is sold or given to someone else, the manual must be provided to the subsequent owner/user of the product. This product is intended for private use only.
General Warnings
CHOKING HAZARD! Keep packaging materials (plastic bags, rubber bands, etc.) away from children! CHOKING HAZARD!
RISK OF ELECTRIC SHOCK! This device contains electronic components powered by a power source (batteries). Never let children use the device unsupervised! Use the device only as described in the manual; otherwise, there is a RISK OF ELECTRIC SHOCK!
RISK OF FIRE/EXPLOSION! Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit or throw the device or batteries into a fire! Excessive heat or improper handling can cause short circuits, fires, and even explosions!
NOTE! Do not immerse the device in water.
Do not expose the device to strong impacts, shocks, dust, prolonged high temperatures, or extreme humidity. This can lead to malfunctions, short circuits, damage to batteries, and components.
Do not disassemble the device! In case of a defect, please contact your dealer. The dealer will contact the service center and can send the device in for repair if necessary.
Use only the recommended batteries. Always replace weak or used batteries with a new set of batteries with full capacity. Do not use batteries of different brands, types, or capacities. Remove batteries from the device if it will not be used for a long time!
The manufacturer is not liable for damage caused by voltage due to improperly inserted batteries!
General Information
This model is available in different variants. The functionalities and technical data are identical; they only differ in design/color.
Scope of Delivery (Fig. 1)
Wall clock, Instruction manual
Required batteries: 1 x 1.5V battery (Size AA/LR6). Batteries not included with purchase.
Parts Overview
Wall clock (Fig. 2)
- 1. Dial plate
- 2. Clock hands (hours, minutes, seconds)
- 3. Humidity display (indoor)
- 4. Temperature display (indoor)
- 5. Wall mount
- 6. Battery compartment
- 7. RESET button
- 8. REC button
- 9. M.SET button
- 10. Locking pin
Getting Started/Power Supply
1. Remove the locking pin (10) from the clockwork. The clock can only be operated after the pin has been removed.
2. Insert one battery (1.5V, AA/LR6) into the battery compartment (6).
Time Setting
NOTE! Upon receiving the DCF time signal, the time will be set according to Central European Time (CET). The switch between summer and winter time (and vice versa) also occurs automatically.
Automatic Time Setting via DCF Signal
After inserting the battery, the time will be automatically set via the DCF radio signal. This process may take a few minutes. During this time, the clock hands will turn several times with interruptions until the correct time is displayed.
Initiate DCF Time Signal Reception Manually
NOTE! Use this function if, for example, the automatic summer/winter time change is not recognized, or if the radio wall clock has temporarily lost DCF reception.
1. To perform a manual search for the DCF signal, press the REC button (8) for approximately 3 seconds.
2. The hands will move to the reception position (12:00), and the radio wall clock will attempt to receive the DCF signal.
3. Wait approximately 2-5 minutes until the current time is displayed.
Manual Time Setting
NOTE! Manual time setting is necessary when the radio wall clock is to be operated outside the DCF signal reception range.
1. Press and hold the M.SET button (9) for approximately 3 seconds.
2. As soon as the minute hand starts moving, you can set the time manually:
- Briefly press the M.SET button to set the time in minute steps.
- Hold down the M.SET button to adjust the time continuously.
3. When you release the M.SET button, the set time will be automatically adopted, and you will exit manual time setting mode.
Temperature and Humidity Display
The temperature (4) and humidity (3) measurements are taken manually. It may take a few minutes for the currently measured value to be displayed.
Mounting/Positioning
NOTE! Always ensure secure mounting or placement. Dropping the device can cause severe damage for which the manufacturer is not liable!
The wall clock can be mounted on the wall using the wall mount (5).
Troubleshooting
Connection Interference
Radio signals from other household devices, such as doorbells, security systems, and entry control systems, can interfere with this device and cause temporary malfunctions. This is normal and does not fundamentally impair the functionality. Radio signal transmission will resume once the interference has passed.
Other Malfunctions
If the radio wall clock no longer responds to button presses or if other malfunctions occur, follow these steps.
NOTE! All previously received DCF data will be deleted.
1. Press the RESET button (7) with a pointed object (e.g., a ballpoint pen).
2. The hands will move to the reception position (12:00), and the radio wall clock will attempt to receive the DCF signal.
3. Wait approximately 2-5 minutes until the current time is displayed.
Cleaning and Maintenance
Before cleaning the device, disconnect it from the power supply (remove batteries)!
Clean the device exterior only with a dry cloth. Do not use cleaning fluids to avoid damaging electronic components.
Protect the device from dust and moisture! Batteries should be removed from the unit if it is not used for a long time.
Disposal
Dispose of packaging materials separately according to type. For information on proper disposal, contact your local waste disposal service or environmental authority.
Do not dispose of electronic devices with household waste!
In accordance with European Directive 2002/96/EC on waste electrical and electronic equipment and its transposition into national law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.
Warranty & Service
The regular warranty period is 2 years, starting from the day of purchase. To benefit from an extended voluntary warranty period as stated on the gift box, registration on our website is required.
You can consult the full warranty conditions and information on warranty extension and services at www.bresser.de/warranty_terms.
EC Declaration of Conformity
Hereby, Bresser GmbH declares that the radio equipment type with article number 8020315000000 complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.bresser.de/download/8020315000000/8020315000000_CE.pdf
Bresser | Teleskope, Mikroskope, Ferngläser & Wetterstationen
