EverStart JUS750CE 750 Peak Amps Jump Starter with Compressor

Features

The EverStart JUS750CE is a versatile jump starter with an integrated air compressor and USB power ports. Key components include:

• 1. Negative (-) Black Clamp
• 2. Backlit LCD Screen
• 3. Built-in 120 Volt AC Charger (under protective cover)
• 4. 2-LED White Area Light
• 5. Positive (+) Red Clamp
• 6. USB Charging Ports (2)
• 7. Compressor Power Button
• 8. Decrease Compressor Pressure Control Button (-)
• 9. USB Power Button
• 10. Area Light Power Button
• 11. Increase Compressor Pressure Control Button (+)
• 12. Jump Starter Power Switch
• 13. Nozzle Adapter
• 14. Air Hose Storage
• 15. Air Hose and Sure Fit® Nozzle

Digital LCD Screen

The unit features a digital LCD screen that displays various information depending on the function:

• Digital Display: Shows voltage, PSI, or other function-specific data.
• Battery Status Icon: Indicates the charge level of the unit's internal battery with bars (full, partial, low, empty).
• Clamp Icons: Indicate connection status of the jump starter clamps.
• Arrow Icons: Used in conjunction with clamp icons.
• Alarm Icon: Alerts the user to fault conditions or reverse polarity.
• Battery Voltage Indicator: Displays the battery voltage in Volts (V).
• Compressor Pressure Indicator: Displays the air pressure in Pounds per Square Inch (PSI).
• Fault Icon: Indicates a fault condition with USB ports or other system errors.
• Jump Starter Icon: Indicates the jump starter function is active or in standby.
• Compressor Icon: Indicates the compressor function is active.
• USB Icon: Indicates the USB ports are active.

Safety Guidelines / Definitions

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or property damage.

RISK OF UNSAFE OPERATION: Basic safety precautions should always be followed. Improper operation, maintenance, or modification can lead to serious injury and property damage. Use only for intended applications. Read and understand all warnings and operating instructions before use.

General Safety Warnings and Instructions

This unit is designed for household use only.

WARNING – Risk of fire, electric shock, burst hazard, or injury:

• Avoid damp or wet locations; do not use in rain.
• Keep children and visitors away from the work area.
• Dress properly: avoid loose clothing or jewelry. Use rubber gloves and non-skid footwear. Contain long hair.
• Store idle appliances indoors in a dry, locked-up place, out of reach of children.
• Do not abuse the cord; never carry by the cord or yank to disconnect. Keep cord from heat, oil, and sharp edges.
• Disconnect the appliance from power before servicing or changing accessories.
• Use Ground Fault Circuit Interrupter (GFCI) protection on circuits or outlets.
• Use of unrecommended accessories or attachments can be hazardous.
• Stay alert and use common sense; do not operate when tired or impaired.
• Check for damaged parts; replace any damaged part by the manufacturer before further use. Do not use if the switch does not operate correctly.
• Do not operate near flammable liquids or in gaseous or explosive atmospheres; motors spark and may ignite fumes.
• Never submerge this unit in water; do not expose it to rain, snow, or use when wet.
• Disconnect from power source before maintenance or cleaning.
• This equipment produces arcs or sparks; if used in an enclosed area, place unit at least 18 inches above the floor.
• Do not insert foreign objects into USB ports.

Specific Safety Instructions for Charging This Unit

• IMPORTANT: Unit is delivered partially charged. Fully charge for 24 hours or until the battery status icon shows 4 solid bars before first use. The unit cannot be overcharged using the AC method.
• Use only the built-in AC charger.
• Turn off all functions when charging or not in use. Ensure all switches are OFF before connecting to power.

Extension Cords

WARNING: Use of an improper extension cord can result in fire and electric shock. Ensure the cord's pins match the charger's and use a heavy enough gauge for the product's current draw. Undersized cords cause voltage drop, power loss, and overheating.

Minimum Gauge for Cord Sets:

Gauge by Amperage Rating and Cord Length:

When using an extension cord, ensure:

• Pins match the charger's.
• Cord is properly wired and in good electrical condition.
• Wire size is adequate for the charger's AC rating.

CAUTION: Pull the extension cord by the plug, not the cord, when disconnecting.

Specific Safety Instructions for Jump Starters

WARNING: Burst hazard

Do not use for dry-cell batteries; they may burst. Use only for lead-acid batteries. Not intended for low-voltage electrical systems other than starter-motor applications.

Use of unsupplied or unrecommended attachments may cause shock or injury.

WARNING: Risk of explosive gases

Batteries generate explosive gases. Always read and follow instructions. Review cautionary markings on products and engines.

CAUTION:

• NEVER attempt to jump-start or charge a frozen battery.
• Vehicles with computerized systems may be damaged; consult the owner's manual before jump-starting.
• Never smoke or allow sparks/flames near the battery, engine, or power station.
• Stay clear of fan blades, belts, pulleys, and other moving parts.
• Remove personal metal items (rings, necklaces, watches) when working with batteries to avoid severe burns from short circuits.
• Do not wear vinyl clothing; friction can cause static sparks.
• Be careful not to drop metal tools on the battery; it may cause sparks or explosion.
• Perform jump-start procedures in a safe, dry, well-ventilated area.
• Always store battery clamps when not in use. Never touch clamps together to avoid sparks or explosion.
• Keep unit on a flat, stable surface away from moving vehicle parts.
• Never allow red and black clamps to touch each other or common conductors to prevent damage and hazards.
• Connection Procedure (Negative-Grounded Systems - Most Common): Connect positive (red) clamp to positive battery post; connect negative (black) clamp to vehicle chassis or engine block away from the battery (not to carburetor, fuel lines, or sheet metal). Connect to a heavy gauge metal part.
• Connection Procedure (Positive-Grounded Systems): Connect negative (black) clamp to negative battery post; connect positive (red) clamp to vehicle chassis or engine block away from the battery.
• If clamps are connected incorrectly (reverse polarity), the LCD will display fault icons, and the unit will sound a continuous alarm until disconnected. Disconnect and reconnect with correct polarity.
• Always disconnect the negative (black) cable first, then the positive (red) cable (except for positive grounded systems).
• Do not expose battery to fire or intense heat; protect terminals with tape before disposal.
• Place unit as far from the battery as cables permit.
• Never allow battery acid to contact the unit.
• Do not operate in a closed area or restrict ventilation.
• Use only on vehicles with 12-volt DC battery systems.
• Do not use as a replacement for a vehicular battery or operate a vehicle without a battery.
• Excessive engine cranking can damage the starter motor; discontinue if the engine fails to start after recommended attempts.
• Do not use on watercraft; not qualified for marine applications.
• Keep unit upright during storage, use, and recharging. Protect from direct sunlight, heat, and moisture.

Specific Safety Instructions for USB Ports

• Do not insert foreign objects into USB ports.
• Do not attach USB hubs or more than one personal electronic device per port.
• Do not use for appliances requiring more than 2.1 amps total from the USB ports.
• Some household USB-powered electronics may not operate with this unit.

Specific Safety Instructions for Compressors

CAUTION:

• Never leave the compressor unattended while in use.
• Do not operate continuously for longer than approximately 10 minutes (depending on ambient temperature) to prevent overheating and damage. Follow instructions in the "Portable Compressor" section.

WARNING – Burst hazard:

• Follow instructions on articles to be inflated carefully.
• Never exceed the recommended pressure listed on articles. If no pressure is given, contact the article manufacturer before inflating.
• Monitor pressure at all times on the LCD screen.

First Aid

Always ensure immediate assistance is available when working with lead-acid batteries.

Always wear protective eyewear. Contact with battery acid can cause blindness or severe burns. Be aware of first aid procedures.

Keep plenty of fresh water and soap nearby.

• Skin: If battery acid contacts skin, rinse immediately with water, then wash thoroughly with soap and water. Seek medical attention if redness, pain, or irritation occurs.
• Eyes: If battery acid contacts eyes, flush immediately for at least 15 minutes and seek immediate medical attention.
• LCD liquid crystal display: If liquid crystal contacts skin, wash with plenty of water and remove contaminated clothing. If it gets into eyes, flush with clean water and seek medical attention. If swallowed, rinse mouth thoroughly, drink water, and induce vomiting. Seek medical attention.

Common Actions and Unit Responses

The following actions turn the unit on and activate the LCD screen:

• Pressing the LED Area Light Power Button: A beep sounds, the Area Light turns on. Backlight is on for 10 seconds. LCD shows Battery Status Icon and Battery Voltage Indicator. Unit stays on until button is pressed again.
• Pressing the USB Power Button: A beep sounds, USB Ports turn on. Backlight is on for 10 seconds. LCD shows Battery Status Icon, Battery Voltage Indicator, and USB Icon. Unit stays on until button is pressed again.
• Pressing the Compressor Power Button: A beep sounds, LCD shows Battery Status Icon, PSI, and Compressor Icon. If no further action, LCD reverts to Battery Status Icon and Voltage Indicator for 10 seconds before auto-shutoff.
• Connecting clamps properly: A beep sounds, LCD shows Battery Status Icon, Battery Voltage Indicator, Clamp Icons, "+" and "-" signs, and flashing Jump Starter Icon. Unit stays on until clamps are disconnected.
• Jump Starter Power Switch ON without battery connection: A 2-second warning sounds every 10 seconds. LCD shows Battery Status Icon, Battery Voltage Indicator, Clamp Icons, "+" and "-" signs. Alarm Icon and Jump Starter Icon flash. Unit stays on until switch is turned OFF.
• Reverse polarity clamp connection: LCD shows Battery Status Icon, Battery Voltage Indicator, Clamp Icons. Alarm Icon, "+" and "-" signs, and Reverse Polarity Icons flash. Unit sounds continuous alarm until clamps are disconnected.
• Unit charging/recharging via AC: Backlight turns on for 10 seconds. LCD shows Battery Status Icon and Battery Voltage Indicator. Battery Status Icon bars change from empty to solid repeatedly.

Note: The unit automatically powers off when all functions are turned off.

Viewing Battery Status

The Battery Status Icon and Battery Voltage Indicator show the battery charge level:

• Full Capacity: Four solid bars.
• Partially Charged: Two or three solid bars.
• Nearly Empty: One solid bar. Charge the unit.
• Completely Empty: Four blank bars. Unit MUST be charged; low voltage protection will activate. Empty icon flashes before auto-shutoff. Unit will not operate until recharged.

Charging/Recharging

The unit is delivered partially charged and must be fully charged before first use. Initial AC charge should be for 24 hours or until the Battery Status Icon shows 4 solid bars.

Lead-acid batteries require routine maintenance. They lose energy over time and need periodic charging. Recharge at least every 30 days and after each use if not in frequent use.

CAUTION: Failure to keep the battery charged will cause permanent damage and reduce performance.

IMPORTANT NOTES:

• Recharging after each use prolongs battery life. Frequent heavy discharges or overcharging reduce battery life.
• Turn off all other unit functions during recharging.
• If the unit appears fully charged but is discharged, the internal battery may have high impedance. Leave charging for 40 hours using the built-in AC charger.

Charging/Recharging Using the Built-In 120 Volt AC Charger and AC Extension Cord (not included):

1. Lift the protective cover of the built-in 120 Volt AC Charger. Connect an extension cord to the unit and plug into a standard 120-volt AC wall outlet. The LCD screen will display charging status.
2. Charge for approximately 24 hours or until the Battery Status Icon shows 4 solid bars.
3. When charging is complete, unplug the AC extension cord from the outlet and then disconnect it from the unit.

Jump Starter

The unit has a jump starter power switch that allows energy flow only when proper connections are made to the battery and frame.

Connection Procedure (Negative-Grounded Systems): Connect positive (red) clamp to positive battery post; connect negative (black) clamp to vehicle chassis or engine block away from the battery.

Connection Procedure (Positive-Grounded Systems): Connect negative (black) clamp to negative battery post; connect positive (red) clamp to vehicle chassis or engine block away from the battery.

IMPORTANT: Turn off the Compressor Power Button before using as a Jump Starter.

WARNING: Follow all safety instructions. Never touch clamps together. If clamps are connected incorrectly (reverse polarity), the unit will sound a continuous alarm, and the LCD will display fault indicators. Disconnect and reconnect with correct polarity.

If the Jump Starter Power Switch is turned on and clamps are not connected to a battery, a warning will sound every 10 seconds, and the LCD will display relevant icons and flashing indicators.

PROCEDURE:

1. Turn off vehicle ignition and all accessories. Place vehicle in "park" and set the emergency brake.
2. Ensure the jump-starter power switch is OFF.
3. Remove jumper clamps from tabs. Connect the red clamp first, then the black clamp.
4. For NEGATIVE GROUNDED SYSTEMS (Most Common): Connect positive (+) red clamp to vehicle battery’s positive terminal. Connect negative (-) black clamp to chassis or a solid, non-moving, metal vehicle component or body part away from the battery.
5. For POSITIVE GROUND SYSTEMS: Connect negative (-) black clamp to vehicle battery’s negative terminal. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or body part away from the battery.
6. When clamps are connected properly, the LCD will indicate the unit is ready to jump-start (solid icons, flashing Jump Starter Icon).
7. Turn the Jump-Starter Power Switch ON. The Engine Icon will light solid, indicating it's time to start the vehicle. Crank the engine in 5-6 second bursts until it starts. The LCD will display jump-starting status.
8. Turn the Jump-Starter Power Switch OFF.
9. Disconnect the negative (-) clamp first, then the positive (+) clamp.

IMPORTANT: Always turn the unit OFF when not in use. Recharge fully after each use.

CAUTION: Vehicles with computerized systems may be damaged; consult the manual. Excessive cranking can damage the starter motor; discontinue if the engine fails to start. If the vehicle fails to start, turn off the unit, disconnect leads, and contact a qualified technician.

LED Area Light

The unit has a built-in 2-LED Area Light controlled by the Area Light Power Button.

1. Press the Area Light Power Button once to turn the light on.
2. Press the button again to turn it off.

When turned on, a beep sounds, the backlight is on for 10 seconds, and the LCD displays Battery Status and Voltage. Periodically check the battery status on the LCD.

IMPORTANT: Ensure the Area Light is OFF when the unit is being recharged or stored.

USB Ports

The USB Power Button and two USB Ports are on the front. They provide a total of 2.1A (5V each).

When USB Ports are in use, the unit monitors for fault conditions (low battery voltage, overload, short circuit). If a fault occurs, the Fault Icon flashes, and USB Ports shut down. Disconnect the USB device, press the USB Power Button to turn off ports, ensure the unit is charged, and allow it to cool before retrying. If the fault persists, check device draw (not exceeding 2.1A) or have the USB device checked.

USING THE USB PORTS:

1. Press the USB Power Button to turn on both USB Ports. A beep sounds, backlight is on for 10 seconds, and the LCD shows Battery Status Icon, Battery Voltage Indicator, and USB Icon.
2. Plug USB-powered device into the port(s) and operate normally.
3. Press the USB power button again to turn off the USB Ports.

Periodically check the unit's battery status. Ensure USB Ports are OFF when recharging or storing.

Notes: USB Ports do not support data communication, only power. Some household USB electronics may not operate with this unit.

Portable Compressor

The built-in 12-volt DC compressor is suitable for vehicle tires, trailer tires, and recreational inflatables. A nozzle adapter is supplied. The compressor hose and Sure Fit® nozzle are stored in the unit.

IMPORTANT: Turn off the Jump Starter Power Button before using as a Jump Starter.

WARNING: Follow all safety instructions for compressors.

CAUTION: The compressor may operate normally or rev down temporarily to prevent overheating. Do not operate continuously for longer than 10 minutes. If longer operation is needed, turn off and restart after a 30-minute cooling period.

The compressor can inflate up to 120 PSI. It can fill up to 3 average tires before recharging is needed.

Inflating Tires or Products With Valve Stems:

1. Screw the Sure Fit® nozzle onto the valve stem. Do not overtighten.
2. Press the Compressor Power Button. A beep sounds, and the LCD shows the Compressor Icon. The display alternates between the set PSI and the current pressure.
3. Use the "+" and "-" buttons to set the desired pressure (3-120 PSI). The unit beeps with each press. Holding a button speeds up selection.
4. Press the Compressor Power Button again to begin inflating. The Compressor Icon flashes, and the display shows the current pressure. Monitor pressure on the LCD.
5. When the desired pressure is reached, the compressor stops automatically.
6. Press the Compressor Power Button to turn off the unit.
7. Unscrew and remove the Sure Fit® nozzle.
8. Allow the unit to cool, then recharge before storing.
9. Store the compressor hose and nozzle in the storage compartment.

Inflating Other Inflatables Without Valve Stems:

1. Screw the nozzle adapter into the Sure Fit® nozzle.
2. Insert the nozzle adapter into the item to be inflated.
3. Follow steps 2 through 4 of the "Inflating Tires or Products With Valve Stems" section.

IMPORTANT: Small items inflate quickly; set pressure carefully to avoid over-inflation.

When desired pressure is reached, the compressor stops automatically. Press the Compressor Power Button to turn off the unit. Disconnect the adapter, unscrew it from the Sure Fit® nozzle, allow the unit to cool, and recharge before storing.

Care and Maintenance

Batteries lose energy over time and need periodic charging. Recharge at least every 30 days when not in use.

Wipe the exterior with a soft cloth. Do not immerse the appliance in water.

There are no user-replaceable parts. Periodically inspect adapters, connectors, and wires. Contact the manufacturer for replacement of worn or broken components.

Battery Replacement/Disposal

The battery should last the service life of the unit, depending on recharge cycles and proper care.

SAFE BATTERY DISPOSAL: Contains a sealed, non-spillable, lead-acid battery that must be disposed of properly according to local, state, and federal regulations. Recycling is required.

WARNINGS:

• Do not dispose of the battery in fire; it may explode.
• Protect exposed terminals with heavy-duty electrical tape before disposal to prevent shorting.
• Do not expose battery to fire or intense heat.

Troubleshooting

Accessories

Recommended accessories may be available from the manufacturer. Contact (877) 571-2391 for assistance.

WARNING: Using unrecommended accessories can be hazardous.

Service Information

For technical advice, repair, or genuine factory replacement parts, contact the manufacturer at (877) 571-2391.

One-Year Limited Warranty

The manufacturer warrants this product against defects in materials and workmanship for ONE (1) YEAR from the date of retail purchase by the original end-user purchaser. Claims can be handled by returning the product to the manufacturer for repair or replacement, or by exchanging it at a participating retailer within their return policy period. Proof of purchase may be required.

This warranty does not apply to accessories, bulbs, fuses, and batteries; defects from normal wear and tear, accidents, shipping damage, alterations, unauthorized use or repair, neglect, misuse, abuse, or failure to follow care and maintenance instructions.

This warranty grants specific legal rights that may vary by state or province. The product is not intended for commercial use.

Appendix

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received.

This equipment has been tested and found to comply with the limits for a Class B digital device, providing reasonable protection against harmful interference in residential installations. It generates, uses, and can radiate radio frequency energy. If not installed and used per instructions, it may cause radio interference. If interference occurs, try reorienting the antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a dealer or technician.

Changes or modifications not approved by the responsible party could void the user's authority to operate the equipment.

Specifications

• Boost Ampere: 12V DC, 750A peak battery, 375A instantaneous
• Battery Type: Maintenance-free, sealed lead acid, 12V DC, 9Ah
• AC Input: 120V AC, 60Hz, 9W
• Area Light: 2 white LEDs
• USB Ports: 2.1A (5V DC each) max.
• Compressor Maximum Pressure: 120 PSI

Sure Fit® is a registered U.S. trademark owned by Baccus Global, LLC.

Imported by Baccus Global LLC, 621 NW 53rd St., Suite 450, Boca Raton, FL 33487

www.Baccusglobal.com 1-877-571-2391