TÜV Rheinland Test Report: IKEA LED2411G3NA LED Lamp

Test Report Number: CN25WZLT 001

Client Reference Number: 1288983

Client: IKEA of Sweden AB

Test Item: Self-ballasted LED lamps

Identification / Type No.: LED2411G3NA

Order Date: 2024-12-16

Date of Sample Receipt: 2025-03-06

Testing Period: 2025-03-20 ~ 2025-06-12

Place of Testing: TÜV Rheinland (Shanghai) Co., Ltd.

Test Result: Pass

General Remarks

All attachments are integral parts of this test report. This applies especially to the following appendix: Appendix A: Photographs of the Test Set-up.

Test Sites

Test Facilities

TÜV Rheinland (Shanghai) Co., Ltd. is located at Workshop14, North Half of Workshop 10 and Workshop 16, Pingqian (Taicang) Modern Industrial Park, No.525, Yuewang Lingang South Road, Shaxi, Taicang, Jiangsu, China. The test equipment used is in accordance with CISPR 16 for measurement of radio interference.

The Federal Communications Commission has reviewed the technical characteristics of the radiated and conducted emission facility and found them to be in compliance with section 2.948 of the FCC rules. The test facility is listed under FCC registration number 930979.

The Innovation, Science and Economic Development Canada has reviewed the technical characteristics of the radiated and conducted emission facility and found them to be in compliance. The test facility is listed under chambers filing number 33038.

List of Test and Measurement Instruments

Table 1: List of Test and Measurement Equipment

Equip. Description Model Manufacturer Due Date
EMC-C-196 Wireless connectivity tester CMW270 Rohde & Schwarz 23.08.2025
EMC-C-302 Signal generator SMB100B (6 GHz) Rohde & Schwarz 10.12.2025
EMC-C-303 Vector Signal generator SMW200A Rohde & Schwarz 10.12.2025
EMC-C-304 OSP OSP-B157W8 Rohde & Schwarz 10.12.2025
EMC-C-161 Spectrum analyser FSV40 Rohde&Schwarz 15.07.2025
EMC-C-018 Double ridged horn antenna BBHA 9120 D Schwarzbeck 24.03.2026
EMC-C-066 EMI test receiver ESCI Rohde&Schwarz 27.10.2025
EMC-C-068 Broadband horn antenna BBHA 9170 Schwarzbeck 18.06.2028
EMC-C-155 BiLog antenna CBL 6112D Teseq 24.03.2026
EMC-C-175 Preamplifier EMC051845SE EMCI Taiwan 24.07.2025
EMC-C-176 Preamplifier EMC184045SE EMCI Taiwan 24.07.2025
EMC-C-001 3 m semi-anechoic chamber SAC3 Frankonia 03.12.2026
EMC-C-141 Shielded enclosure 10.055x3.605x3.000 Frankonia 08.11.2028
EMC-C-195 EMI test receiver ESR3 Rohde&Schwarz 03.08.2025
EMC-C-190 Artificial mains network ENV432 Rohde&Schwarz 11.10.2025
EMC-S-036 RF measurement software WMS32-WB (11.40.00) Rohde&Schwarz NA
EMC-S-032 EMI measurement software EMC32-E+ (10.60.20) Rohde&Schwarz NA
EMC-S-028 EMI measurement software EMC32-MEB (10.60.20) Rohde&Schwarz NA

Traceability

All measurement equipment calibrations are traceable to NIST or where calibration is performed outside the United States, to equivalent nationally recognized standards organizations.

Calibration

Equipment requiring calibration is calibrated periodically by the manufacturer or according to manufacturer's specifications. Additionally all equipment is verified for proper performance on a regular basis using in-house standards or comparisons.

Measurement Uncertainty

Table 2: Measurement Uncertainty

Measurement Type Frequency Uncertainty
Antenna Port Conducted Emission < 1GHz ±0.39dB
> 1GHz ±0.68dB
Conducted Emission 150kHz - 30MHz ±2.33dB
9kHz - 30MHz ±2.93dB
Radiated Emission 30MHz - 1GHz ±5.34dB
> 1GHz ±5.40dB

General Product Information

Product Function and Intended Use

The EUT (Equipment Under Test) is a LED lamp which supports Bluetooth, Zigbee and Thread. The aim of this report is to evaluate the RF character of Thread of the EUT.

Ratings and System Details

Table 3: Technical Specification of EUT

Attribute Value
General Description of EUT Self-ballasted LED lamps
Product Name LED2411G3NA
Operation Voltage AC 120V, 60Hz
Test Voltage DC 3.3V for RF conducted and radiated test; AC 120V, 60Hz for conducted emission test
RF Technical 1) BLE
2) Zigbee
3) Thread
RF IC SiMG301
Frequency Range 2405~2480MHz
Modulation Type OQPSK
Antenna Type Monopole Antenna
Antenna Gain 1.23 dBi (declared by client)

Table 4: Operation Channel List

RF Channel Frequency [MHz] RF Channel Frequency [MHz] RF Channel Frequency [MHz] RF Channel Frequency [MHz]
11 2405 15 2425 19 2445 23 2465
12 2410 16 2430 20 2450 24 2470
13 2415 17 2435 21 2455 25 2475
14 2420 18 2440 22 2460 26 2480

Independent Operation Modes

Test frequencies are lowest channel: 2405 MHz, middle channel: 2445 MHz and highest channel: 2480 MHz. The basic operation modes are: A. Thread transmitting mode, B. Radio operating mode.

Noise Generating and Noise Suppressing Parts

Refer to the Circuit Diagram.

Test Set-up and Operation Modes

Principle of Configuration Selection

The equipment under test (EUT) was configured to measure its maximum power level. The test modes were adapted accordingly in reference to the instructions for use.

Test Operation and Test Software

Test operation refers to test setup in chapter 5. All testing were performed according to the procedures in ANSI C63.10: 2013. Test Software: SSCOM 5.12.1

Table 5: Power parameter value

Mode Power Parameter Setting Value
Thread 80

Special Accessories and Auxiliary Equipment

Table 6: Auxiliary Equipment

Equipment Manufacturer Model
Laptop Lenovo 21AJ-S57N0J
Mobile phone Apple iPhone 15
Loudspeaker Apple HomePod mini
Remote control IKEA E2489

Countermeasures to achieve EMC Compliance

Null.

Test Results

Conducted Testing at Antenna Port

Antenna Requirement

RESULT: Pass

According to the manufacturer declared, the EUT has one internal monopole antenna, the directional gain of antenna is 1.23 dBi and the antenna is designed with permanent attachment and no consideration of replacement. Therefore the EUT is considered sufficient to comply with the provision.

Table 7: Antenna Requirement
Requirement Results Verdict
FCC 15.203 – Antenna Requirement 1: No antenna other than that furnished by the responsible party shall be used with the device Antenna type: Monopole Antenna Pass
FCC 15.204 – Antenna Requirement 2: An intentional radiator may be operated only with the antenna with which it is authorized. If an antenna is marketed with the intentional radiator, it shall be of a type which is authorized with the intentional radiator. Only one monopole antenna can be used Pass
RSS-Gen 6.4 – External Control: The device shall not have any external controls accessible to the user that enable it to be adjusted, selected or programmed to operate in violation of the regulatory requirements, including RSS-Gen and the applicable RSSs The device does not have any transmitter external controls accessible to the user that can be adjusted and operated in violation of the limits of this standard. PASS

RSS-Gen 6.8 – Antenna Requirement: When measurements at the antenna port are used to determine the RF output power, the effective gain of the device's antenna shall be stated, based on a measurement or on data from the antenna's manufacturer.

Results: a) Antenna Type: Monopole Antenna; b) Manufacture: N/A; c) Model No.: N/A; d) Gain with reference to an isotropic radiator: 1.23 dBi

Verdict: PASS

6dB & 99% Bandwidth

RESULT: Pass

Date of testing: 2025-05-27~2025-05-28

Ambient temperature: 21.4°C~23.7°C

Relative humidity: 50.4%~51.3%

Atmospheric pressure: 101kPa

Test requirement: FCC Part 15.247(a)(2), RSS-247 Issue 3, August 2023, Clause 5.2(a), RSS-Gen Issue 5, Amendment 2, February 2021, Clause 6.7

Test procedure: ANSI C63.10: 2013

Test voltage: DC 3.3V

Test modes applied: A

6dB Bandwidth, 2405MHz
DUT Frequency (MHz) Bandwidth (MHz) Limit Min (MHz) Limit Max (MHz) Band Edge Left (MHz) Band Edge Right (MHz)
2405.000000 1.750000 0.500000 --- 2404.125000 2405.875000
2405.000000 Max Level (dBm): 4.9 Result: PASS

Graphical representation shows the 6 dB Bandwidth plot for 2405MHz.

6dB Bandwidth, 2445MHz
DUT Frequency (MHz) Bandwidth (MHz) Limit Min (MHz) Limit Max (MHz) Band Edge Left (MHz) Band Edge Right (MHz)
2445.000000 1.750000 0.500000 --- 2444.125000 2445.875000
2445.000000 Max Level (dBm): 5.2 Result: PASS

Graphical representation shows the 6 dB Bandwidth plot for 2445MHz.

6dB Bandwidth, 2480MHz
DUT Frequency (MHz) Bandwidth (MHz) Limit Min (MHz) Limit Max (MHz) Band Edge Left (MHz) Band Edge Right (MHz)
2480.000000 1.750000 0.500000 --- 2479.125000 2480.875000
2480.000000 Max Level (dBm): 4.5 Result: PASS

Graphical representation shows the 6 dB Bandwidth plot for 2480MHz.

99% Occupied Channel Bandwidth, 2405MHz
DUT Frequency (MHz) Bandwidth (MHz) Limit Min (MHz) Limit Max (MHz) Band Edge Left (MHz) Band Edge Right (MHz)
2405.000000 2.235000 --- --- 2403.867500 2406.102500
2405.000000 Result: PASS

Graphical representation shows the 99% Occupied Channel Bandwidth plot for 2405MHz.

99% Occupied Channel Bandwidth, 2445MHz
DUT Frequency (MHz) Bandwidth (MHz) Limit Min (MHz) Limit Max (MHz) Band Edge Left (MHz) Band Edge Right (MHz)
2445.000000 2.235000 --- --- 2443.867500 2446.102500
2445.000000 Result: PASS

Graphical representation shows the 99% Occupied Channel Bandwidth plot for 2445MHz.

99% Occupied Channel Bandwidth, 2480MHz
DUT Frequency (MHz) Bandwidth (MHz) Limit Min (MHz) Limit Max (MHz) Band Edge Left (MHz) Band Edge Right (MHz)
2480.000000 2.250000 --- --- 2478.867500 2481.117500
2480.000000 Result: PASS

Graphical representation shows the 99% Occupied Channel Bandwidth plot for 2480MHz.

Output Power

RESULT: Pass

Date of testing: 2025-06-12

Ambient temperature: 23.8°C

Relative humidity: 56.7%

Atmospheric pressure: 101kPa

Test requirement: FCC Part 15.247(b)(3), RSS-247 Issue 3, August 2023, Clause 5.4(d)

Test procedure: ANSI C63.10: 2013

Test voltage: DC 3.3V

Test modes applied: A

Table 8: Peak Output Power
Frequency [MHz] Peak Conducted Output Power [dBm] Limit [dBm]
2405 8.4 30
2445 8.5 30
2480 8.0 30

Note: 1. The cable loss is taken into account in results. 2. EIRP=Conducted Output Power + Antenna Gain (1.23dBi), which is far below the 4 W (36dBm).

Power Spectral Density

RESULT: Pass

Date of testing: 2025-06-12

Ambient temperature: 23.8°C

Relative humidity: 56.7%

Atmospheric pressure: 101kPa

Test requirement: FCC Part 15.247(e), RSS-247 Issue 3, August 2023, Clause 5.2(b)

Test procedure: ANSI C63.10: 2013

Test voltage: DC 3.3V

Test modes applied: A

Power Spectral Density, 2405MHz
DUT Frequency (MHz) Frequency (MHz) PSD (dBm) Limit Max (dBm) Result
2405.000000 2405.425000 -3.205 8.0 PASS

Graphical representation shows the Peak Power Spectral Density plot for 2405MHz.

Power Spectral Density, 2445MHz
DUT Frequency (MHz) Frequency (MHz) PSD (dBm) Limit Max (dBm) Result
2445.000000 2445.425000 -3.159 8.0 PASS

Graphical representation shows the Peak Power Spectral Density plot for 2445MHz.

Power Spectral Density, 2480MHz
DUT Frequency (MHz) Frequency (MHz) PSD (dBm) Limit Max (dBm) Result
2480.000000 2480.425000 -3.736 8.0 PASS

Graphical representation shows the Peak Power Spectral Density plot for 2480MHz.

Conducted Band Edge and out-of Band Emissions

RESULT: Pass

Date of testing: 2025-06-12

Ambient temperature: 23.8°C

Relative humidity: 56.7%

Atmospheric pressure: 101kPa

Test requirement: FCC Part 15.247(d), RSS-247 Issue 3, August 2023, Clause 5.5

Test procedure: ANSI C63.10: 2013

Test voltage: DC 3.3V

Test modes applied: A

Figure 1: Reference level plots for 2405MHz, 2445MHz, and 2480MHz are provided.

Figure 2: Conducted Spurious Emission plots for 2405MHz, 2445MHz, and 2480MHz are provided.

Figure 3: Conducted Band Edge plots for 2405MHz and 2480MHz are provided.

Emission in the Frequency Range up to 30MHz

Conducted Emission

RESULT: Pass

Date of testing: 2025-03-20

Ambient temperature: 18.1°C

Relative humidity: 52.1%

Atmospheric pressure: 101kPa

Test requirement: FCC Part 15.207 (a), RSS-Gen Issue 5, Amendment 2, February 2021, Clause 8.8

Test procedure: KDB 558074 D01v05r02, ANSI C63.10: 2013

Test voltage: AC 120V, 60Hz

Test modes applied: B

Figure 4: Conducted Emission, L plot and data table are provided.

Figure 5: Conducted Emission, N plot and data table are provided.

Emission in the Frequency Range above 30MHz

Radiated Band-Edge

RESULT: Pass

Date of testing: 2025-05-25

Ambient temperature: 21.2°C

Relative humidity: 50.7%

Atmospheric pressure: 101kPa

Test requirement: FCC Part 15.247(d), FCC Part 15.205(a), FCC Part 15.209(a), RSS-Gen Issue 5, Amendment 2, February 2021, Clause 8.9, RSS-Gen Issue 5, Amendment 2, February 2021, Clause 8.10, RSS-247 Issue 3, August 2023, Clause 5.5

Test procedure: ANSI C63.10: 2013

Test voltage: DC 3.3V

Test modes applied: A

Figure 6 & 7: Radiated Band-Edge plots for 2405MHz (Horizontal and Vertical polarization) are provided.

Figure 8 & 9: Radiated Band-Edge plots for 2480MHz (Horizontal and Vertical polarization) are provided.

Radiated Spurious Emission

RESULT: Pass

Date of testing: 2025-05-25~2025-06-02

Ambient temperature: 20.2°C~21.4°C

Relative humidity: 50.2%~51.6%

Atmospheric pressure: 101kPa

Test requirement: FCC Part 15.247(d), FCC Part 15.209(a), RSS-Gen Issue 5, Amendment 2, February 2021, Clause 8.9, RSS-247 Issue 3, August 2023, Clause 5.5

Test procedure: ANSI C63.10: 2013

Test voltage: DC 3.3V

Test modes applied: A

Note: For the frequency range from 18GHz to 25GHz, no emission was found.

Figure 10: Radiated Spurious Emission plots for 2405MHz (30MHz to 1GHz H/V, 1GHz to 7GHz H/V, 7GHz to 18GHz H/V) are provided.

Figure 11: Radiated Spurious Emission plots for 2445MHz (30MHz to 1GHz H/V, 1GHz to 7GHz H/V, 7GHz to 18GHz H/V) are provided.

Figure 12: Radiated Spurious Emission plots for 2480MHz (30MHz to 1GHz H/V, 1GHz to 7GHz H/V, 7GHz to 18GHz H/V) are provided.

Limit and Margin Summary Tables:

QP (Quasi-Peak)
Frequency (MHz) QuasiPeak (dBμV/m) Pol Corr. (dB/m) Margin - QPK (dB) Limit - QPK (dBμV/m)
30.242500 28.7 H 25.3 11.3 40.0
306.935000 27.9 H 20.4 18.1 46.0
847.588750 33.5 H 29.0 12.5 46.0
32.182500 27.6 V 24.2 12.4 40.0
265.346250 24.3 V 21.2 21.7 46.0
891.723750 33.4 V 28.6 12.6 46.0
PK (Peak)
Frequency (MHz) MaxPeak (dBμV/m) Pol Corr. (dB/m) Margin - PK+ (dB) Limit - PK+ (dBμV/m)
1333.272727 37.7 H -18.7 36.3 74.0
3146.363636 39.2 H -14.6 34.8 74.0
4811.090909 42.2 H -11.2 31.8 74.0
7216.218750 50.3 H -6.0 23.7 74.0
11070.343750 47.7 H -2.1 26.3 74.0
17983.156250 55.8 H 11.8 18.2 74.0
1063.000000 40.4 V -20.0 33.6 74.0
2127.727273 44.7 V -16.5 29.3 74.0
4811.363636 43.0 V -11.2 31.0 74.0
7213.125000 50.2 V -6.0 23.8 74.0
10767.156250 46.7 V -2.1 27.3 74.0
17961.156250 55.9 V 11.5 18.1 74.0
AV (Average)
Frequency (MHz) Average (dBμV/m) Pol Corr. (dB/m) Margin - AVG (dB) Limit - AVG (dBμV/m)
1333.272727 27.5 H -18.7 26.5 54.0
3146.363636 23.8 H -14.6 30.2 54.0
4811.090909 34.1 H -11.2 19.9 54.0
7216.218750 43.8 H -6.0 10.2 54.0
11070.343750 35.1 H -2.1 18.9 54.0
17983.156250 46.0 H 11.8 8.0 54.0
1063.000000 30.9 V -20.0 23.1 54.0
2127.727273 34.5 V -16.5 19.5 54.0
4811.363636 35.7 V -11.2 18.3 54.0
7213.125000 41.6 V -6.0 12.4 54.0
10767.156250 34.5 V -2.1 19.5 54.0
17961.156250 45.5 V 11.5 8.5 54.0

Limit and Margin Summary Tables (Continued):

QP (Quasi-Peak)
Frequency (MHz) QuasiPeak (dBμV/m) Pol Corr. (dB/m) Margin - QPK (dB) Limit - QPK (dBμV/m)
30.242500 28.8 H 25.3 11.2 40.0
299.538750 29.8 H 20.7 16.2 46.0
885.782500 34.0 H 29.2 12.0 46.0
30.485000 28.7 V 25.3 11.3 40.0
260.981250 24.8 V 21.6 21.2 46.0
860.198750 33.9 V 29.1 12.1 46.0
PK (Peak)
Frequency (MHz) MaxPeak (dBμV/m) Pol Corr. (dB/m) Margin - PK+ (dB) Limit - PK+ (dBμV/m)
1330.545455 37.9 H -18.7 36.1 74.0
1865.090909 42.2 H -18.5 31.8 74.0
4959.181818 44.6 H -11.0 29.4 74.0
7438.281250 52.1 H -5.8 21.9 74.0
12397.218750 49.0 H -2.0 25.0 74.0
17988.312500 55.8 H 11.9 18.2 74.0
1465.000000 45.8 V -18.6 28.2 74.0
2128.000000 45.1 V -16.5 28.9 74.0
4958.636364 45.8 V -11.0 28.2 74.0
7441.375000 50.4 V -5.8 23.6 74.0
10392.125000 48.4 V -2.1 25.6 74.0
17974.562500 55.9 V 11.7 18.1 74.0
AV (Average)
Frequency (MHz) Average (dBμV/m) Pol Corr. (dB/m) Margin - AVG (dB) Limit - AVG (dBμV/m)
1330.545455 27.6 H -18.7 26.4 54.0
1865.090909 30.7 H -18.5 23.3 54.0
4959.181818 37.8 H -11.0 16.2 54.0
7438.281250 44.6 H -5.8 9.4 54.0
12397.218750 36.5 H -2.0 17.5 54.0
17988.312500 45.7 H 11.9 8.3 54.0
1465.000000 33.1 V -18.6 20.9 54.0
2128.000000 31.5 V -16.5 22.5 54.0
4958.636364 38.7 V -11.0 15.3 54.0
7441.375000 43.4 V -5.8 10.6 54.0
10392.125000 35.5 V -2.1 18.5 54.0
17974.562500 46.1 V 11.7 7.9 54.0

PDF preview unavailable. Download the PDF instead.

GetApplicationAttachment.html?id=8407363 Microsoft Word for Microsoft 365; modified using iText 4.2.2 by 1T3XT, AuthentiDate

Related Documents

Preview IKEA LED2402C3NA LED Lamp RF Test Report - TÜV Rheinland
Comprehensive RF test report for the IKEA LED2402C3NA LED lamp, covering antenna requirements, bandwidth, output power, spectral density, emissions, and band-edge compliance, conducted by TÜV Rheinland.
Preview TÜV Rheinland Test Report: IKEA LED2406G4NA (Thread Connectivity)
This document is a comprehensive test report by TÜV Rheinland for IKEA's LED2406G4NA self-ballasted LED lamp. It details the evaluation of the product's RF characteristics, specifically focusing on Thread connectivity, and includes results for conducted and radiated emissions, bandwidth, output power, and band-edge compliance according to FCC and RSS standards.
Preview TÜV Rheinland Test Report: IKEA LED2409G6NA Zigbee LED Lamp
This TÜV Rheinland test report details the compliance and RF performance of the IKEA LED2409G6NA self-ballasted LED lamp, which supports Zigbee, Bluetooth, and Thread technologies. The report covers conducted and radiated emissions, bandwidth, output power, and power spectral density according to FCC and RSS standards.
Preview TÜV Rheinland Product Test Report: IKEA LED2411G3NA Self-ballasted LED Lamp
Comprehensive test report by TÜV Rheinland detailing the compliance of IKEA's LED2411G3NA self-ballasted LED lamp with FCC and RSS standards, covering RF performance and emissions.
Preview TÜV Rheinland Test Report: IKEA LED2407G8NA LED Lamp RF Performance
This document presents the RF test results for the IKEA LED2407G8NA LED lamp, conducted by TÜV Rheinland. It covers antenna requirements, bandwidth, output power, power spectral density, conducted emissions, and radiated emissions, adhering to FCC and RSS standards.
Preview TÜV Rheinland Test Report: IKEA LED2411G3NA Zigbee Lamp
This TÜV Rheinland test report details the compliance testing for the IKEA LED2411G3NA, a self-ballasted LED lamp supporting Zigbee, Bluetooth, and Thread. It covers conducted and radiated emissions, bandwidth, output power, and spectral density according to FCC and RSS standards.
Preview Test Report for IKEA LED2408G10NA Self-ballasted LED Lamp
This test report from TÜV Rheinland details the compliance testing for the IKEA LED2408G10NA self-ballasted LED lamp, covering RF performance including bandwidth, output power, spectral density, emissions, and radiated band-edge characteristics.
Preview TÜV Rheinland Test Report: IKEA LED2404G6NA Zigbee RF Compliance
This TÜV Rheinland test report details the RF compliance testing for the IKEA LED2404G6NA self-ballasted LED lamp, covering conducted and radiated emissions, bandwidth, output power, and power spectral density according to FCC and RSS standards.