Orbegozo CPW 04132 Ceiling Fan with Wi-Fi

Introduction

Manufacturer: Sonifer, S.A.
Address: Avenida de Santiago, 86 30007 Murcia, España
Email: sonifer@sonifer.es
Website: www.orbegozo.es
Made in: P.R.C.

Please read this manual carefully before operating this appliance and save it for future reference to obtain the best results and ensure safe use.

For more information about this ceiling fan, including installation details, scan the QR code or visit www.orbegozo.com and search for the model number.

General Safety Instructions

1. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, if they have been given appropriate supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children must never play with the appliance. Cleaning and user maintenance must never be carried out by children without supervision.
2. Children should be supervised to ensure they do not play with the appliance.
3. Keep the appliance and its cord out of the reach of children under 8 years old.
4. CAUTION: For your children's safety, do not leave packaging material (plastic bags, cardboard, polyethylene, etc.) within their reach.
5. If the power supply cord is damaged, it must be replaced by the manufacturer, a service technician, or any other qualified professional.
6. Never unplug by pulling the cord.
7. Do not operate the appliance if the cord or plug is damaged, or if the appliance is not functioning correctly.
8. Do not handle the appliance with wet hands.
9. Never immerse the appliance in water or any other liquid.
10. Before cleaning, ensure the appliance is unplugged.
11. The appliance must be installed in accordance with national regulations for electrical installations.
12. This appliance is for domestic use only.
13. If you need a copy of the instruction manual, it can be found at www.orbegozo.com.
14. WARNING: In case of misuse, there is a risk of possible injury.

Other Specific Safeguards

1. The means of disconnection from the mains supply that must be incorporated into the fixed installation for its all-pole disconnection must present a contact separation of at least 3 mm on all poles.
2. Ensure that the installation location allows for free rotation of the fan blades. Once installed, the blades must be at least 2.30 meters above the floor.
3. If installing more than one fan, ensure you do not mix fan blade sets, even if they are from the same model.
4. Before starting to work with the electrical network, disconnect power by removing fuses or turning off the main circuit breaker.
5. After installing the fan, ensure all fixings are secure to prevent the fan from falling.
6. Check that the fan's mounting point is capable of supporting the fan's weight in motion (minimum 50Kg).
7. The fan must be switched off and stopped before changing the direction of rotation.

Installation of the Fan

To set up this ceiling fan, follow these steps:

1. Fix the mounting bracket: Place the ceiling bracket with screws and wall plugs (depending on ceiling type).
   [Diagram showing ceiling bracket attachment to ceiling]
2. Assemble the down rod: Pass the bar with the swivel support through the trim recess.
   [Diagram showing down rod, ball joint, and canopy assembly]
3. Connect the wiring: Pass the connection cables through the bar and secure them to the motor with the pin.
   [Diagram showing cables threaded through the rod and secured to the motor]
4. Attach the upper ring and blades: Attach the upper ring to the motor. Screw the blades to the motor head.
   [Diagram showing upper ring attachment and blades being screwed to the motor head]
5. Install the light kit holder: Install the tulip holder using the supplied screws.
   [Diagram showing light kit holder installation]
6. Connect the light wire: Fix the light wire via the connector. Make electrical connections according to wire colors. Use the hook to hang the fan while installing connections.
   [Diagram showing light wire connection and electrical hook]
7. Hang the motor: Hang the motor from the ceiling hook on the mounting plate to facilitate electrical connection and place the remote receiver. Use one of the bowl holes to hang the fan on the mounting plate hook. This will help connect the electrical cables. Connect the cables following the wiring instructions. Insert the bowl holes into the ceiling support and screw them in.
   [Diagram showing motor being hung, receiver placement, and canopy attachment to ceiling support]
8. Attach the lampshade/tulip: Attach the tulip by turning it clockwise.
   [Diagram showing the tulip being attached]

Remote Control Receiver Installation

Follow the diagram to install the remote receiver.

[Wiring diagram showing connections for Neutral (Blue wire from receiver to Blue wire in ceiling), Fan connection (Brown wire from receiver to Brown wire in ceiling), Light connection (Black wire from receiver to Black wire in ceiling), and Ground (Green/Yellow wire from fan to Ground in ceiling). The diagram also indicates a sensor.]

Operating the Fan

Using the Remote Control Transmitter

Select the fan speed by pressing the speed control button on the remote transmitter:

• HI: High speed
• MED: Medium speed
• LOW: Low speed
• OFF: Stops the fan.

For Cold Weather: Push the 'UP' switch so the blades move warm air trapped near the ceiling downwards into the room.

For Hot Weather: Push the 'DOWN' switch so the blades create a breeze and circulate air in the room.

Pressing the 'ON/OFF' light button on the remote transmitter controls the fan's light.

Remote Control Operation

Point the remote at the infrared sensor to operate the fan.

• HIGH: Drives the fan at high speed.
• MEDIUM (med): Activates the fan at medium speed.
• LOW (low): Activates the fan at low speed.
• STOP (off): Turns off the fan.
• LIGHT: on/off: Turns the fan light on or off.
• 1H, 2H, 4H: Programs the fan operation (but not the light) for 1 hour, 2 hours, or 4 hours respectively. To do this, start the fan and press one of these 3 buttons; after the selected time, the fan will stop working. (Note: The light cannot be programmed).
• Wi-Fi Symbol: Press and hold to activate Wi-Fi.

The remote control operates with 2 x AAA 1.5V batteries (batteries not included).

Remote Control Battery Replacement

Replace batteries by sliding the battery compartment cover on the remote control transmitter in the direction of the arrow. Insert 2 x AAA batteries. Replace the battery compartment cover, ensuring it is securely closed.

Important Notes:

• Always ensure the battery compartment cover is closed properly.
• Do not expose the remote control to direct sunlight.
• Do not attempt to recharge used batteries. Special rechargeable batteries are available and clearly marked.
• Do not dispose of batteries in fire, as this poses an explosion risk.

Maintenance

How to Replace a LED Bulb

Please contact technical service.

Cleaning

Clean with a soft, dry cloth. Never use scouring pads, abrasive materials, or chemical cleaners. Avoid allowing condensation to come into contact with electrical components.

Wi-Fi Control and App Usage

The Orbegozo CPW series can be controlled via Wi-Fi using the ORBEGOZO APP, available for download on Google Play and the App Store. This allows access to all appliance functions from your mobile phone in a simple and intuitive way.

[Image description: App Store and Google Play download badges]

To review all features of this and other Orbegozo appliances, or to access an explanatory video about configuring the fan with the APP, visit www.orbegozo.com, search for your model, or scan the QR code.

[Image description: QR code for more information]

Information on How to Use the Application

This device allows you to use it via your home Wi-Fi network. A prerequisite is a permanent Wi-Fi connection to your router and the free "Orbegozo APP".

Commissioning via App

1. Install the "Orbegozo APP" application. Create a user account.
2. Activate the Wi-Fi function on your mobile and connect to the wireless network.
3. Long press the Wi-Fi activation button.
4. Enter the app and select "Add device".
5. Select the device from the list or let the app detect the fan automatically.
6. The application will link with the device, allowing you to control it from your mobile.

Disposal of Old Electrical Appliances

In accordance with the European Directive 2012/19/UE on Waste Electrical and Electronic Equipment (WEEE), old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately to optimize the recovery and recycling of their constituent materials, and to reduce the impact on human health and the environment. The crossed-out "wheeled bin" symbol on the product serves as a reminder of your obligation for separate collection when disposing of the appliance. Consumers should contact their local authority or retailer for information regarding the correct disposal of their old appliance.

[Symbol description: A crossed-out wheeled bin indicating separate collection is required]

Declaration of Conformity

This device complies with the requirements of the Low Voltage Directive 2014/35/EU and the requirements of the EMC Directive 2014/30/EU.