Aoocci BX Smart Motorcycle Console

Overview

The Aoocci BX motorcycle smart car system features BSD radar rearview lane change assistance and early warning capabilities. It is also equipped with 1080P high-definition front and rear dual recording cameras to record riding conditions in real time. Supports intelligent functions such as wireless screen projection for mobile phones, motorcycle navigation, and operation of mobile phone apps. Equipped with a 5.5-inch high-brightness display screen and GPS high-precision satellite positioning function, it provides you with an intelligent and convenient riding experience. The main unit is equipped with IP68 dust and water resistance, It can easily handle harsh outdoor environments.

Main body and accessories

• Host*1
• Millimeter wave radar *1
• Camera*2
• Tire Pressure*2
• GPS*1
• Controller
• Wiring Harness*1
• Power*1
• Fixed Base*1
• Quick Release Bracket*1
• L-Bracket*1
• Z-Type Bracket*1
• Reducer Ring*4
• Storage Card 64G*1
• Tools*5

Parts Details

Speaker outlet

Vibration dampener

TF card slot

22mm ball head

microphone

Installation Guide

TF card installation

[Note]
1. Please use a high-speed TF card (Class 10 or above) with a minimum capacity of 16GB and maximum capacity of 128GB.
2. After installation, please format the TF card before first use.

The product is equipped with a 64GB memory card and it has been installed in the equipment at the factory.

Format TF Card

Host-Settings-Format memory card

If the vibration amplitude of the motorcycle is too large, it will be automatically judged as an emergency situation. In emergency situations, videos will be automatically saved without overwriting. At this time, it is easy to fill up the space, making it impossible to store videos in a loop. Therefore, it is necessary to clear the automatically saved videos on the memory card or manually format the memory card every three months.

Vehicle Installation

Select the appropriate reducer ring based on the mounting bar:

• 16mm
• 22mm
• 24.5mm
• 28mm

Installation Diagrams

Ball head bracket installation diagram

Ballhead

Fixed base

Reducing ring

12-28mm bar

Z-type bracket installation diagram

Quick release module

Ball head

Fixed base

Z-type bracket

Motorcycle rearview mirror

Illustration of installation of controller on Lbracket

L-Bracket

Controller

Motorcycle rearview mirror

*The displayed angle is illustrative. Set it to your desired position for practical use.

Wiring Diagram

① Wiring harness connects to the host extension cable

② Rear-CH2 cable connects to the rear camera

③ Front-CH1 cable connects to the front camera

④ Controller cable connects to the controller

⑤ GPS cable connects to the GPS

⑥ Power cable connects to the host power cable

⑦ Power cable B+ connects to the positive terminal of the battery

⑧ Power cable GND+⑪ radar's black (negative) cable connects to the negative terminal of the battery

⑨ Power cable ACC+⑩ radar's red (positive) cable connects to the battery ACC cable

⑫ Front/rear tire pressure sensors. Please install on the corresponding tire.

Installation Notes

GPS Installation Notes

Remove the backing of the 3M adhesive tape and install it onto the bike frame.

• 1. Do not install under carbon fiber parts.
• 2. Cannot be blocked by metal parts.
• 3. Install away from camera, camera wiring and host as possible.
• 4. If GPS cannot receive signal, change the installation location.

Tire Pressure Installation Precautions

By installing a tire pressure detection sensor, the real-time tire pressure can be read, and a pop-up window will appear when the alarm threshold is reached.

Battery life: 1 year

Size parameters: 22.7x18.05mm Battery replacement: CR1632

Tire pressure monitoring range: 0 to 100 psi (0 to 689 kPa)

Tire temperature monitoring range: -40°C to 125°C

The battery can be replaced with tools.

Anti-theft nut

Camera Installation Notes

Tear off the backing of the 3M adhesive and stick the front/rear camera to the front/rear of the motorcycle.

• 1. The camera can be rotated 180° forward and backward by loosening the screws.
• 2. Please adjust the camera arrow mark to face upwards.
• 3. Please clean the surface before applying the adhesive. When attaching, press firmly for at least 10 seconds and let it sit for 30 minutes to ensure the best adhesion.
• 4. If the camera is installed in reverse, please rotate it 180° and adjust the angle accordingly.

Radar Installation Notes

Tear off the backing of the 3M adhesive and install the radar at the rear of the motorcycle. Installation height should be 60-90cm from the ground and the radar should be 90° from the ground.

• 1. The radar can be rotated 180° forward and backward by loosening the screws.
• 2. Please wipe the surface of the pasting position. When pasting, press with all your strength for more than ten seconds and let it stand for 30 minutes to ensure the best pasting effect.

Operation and Interface Introduction

主界面 (Main Interface)

Icons:

• ① Compass
• ② Screen projection
• ③ Dashcam
• ④ Time display
• ⑤ Radar setup
• ⑥ Settings
• ⑦ Tire pressure display
• ⑧ Speed display
• ⑨ Video recording status
• ⑩ TF card status
• ⑪ BSD status
• ⑫ GPS status
• ⑬ Wi-Fi status
• ⑭ Bluetooth status

Swipe down adjustment interface

• ① Volume adjustment: Slide to adjust the volume.
• ② Brightness adjustment: Slide to adjust the screen brightness.
• Auto brightness: Auto screen brightness can be turned on/off.

When wirelessly projecting the screen, the volume and brightness need to be adjusted through the virtual keys.

Recorder interface

• 1. Speed display
• 2. Compass
• 3. Video replay
• 4. Turn on/off the video recording
• 5. Photo button
• 6. Turn on/off the recording
• 7. Locked video
• 8. Recorder Settings
• 9. Front and rear camera switching

When the ordinary video storage space or the emergency video storage space is full, the system will automatically delete the earliest recorded video to activate the loop recording function.

Recorder setting interface

• 1. Video duration: The recording duration of a single video can be set as 1 minute, 2 minutes, or 3 minutes.
• 2. Post-recording Settings: Set the rear camera mirror to correct the reverse preview issue of the picture, or set the rear camera mirror to be used as a rearview mirror.
• 3. Collision sensing RCW: After enabling this function, if a collision occurs during driving, the current video will be locked.
• 4. Sentinel Mode: When this function is enabled while the vehicle is parked and the engine is turned off, if a collision occurs, the video during this period will be marked as locked and classified as an emergency video.
• 5. Recording switch: Turn on/off the recording function.
• 6. Format the SD card: Clear all the files in the SD card.

Radar setting interface

• Radar pairing: Click Pairing to enter the radar pairing state. Bind according to the ID number displayed in the pop-up window on the left. If the radar ID number is not found for a long time, please restart the device or wait for 5 minutes.
• Unbinding radar: Unbind the radar.
• Radar switch: Set the radar on/off.
• Radar mirror: Turn on this function when the radar base is installed upwards.
• Radar rear view: After enabling this function, when a radar signal is detected, the rear streaming media image will be displayed synchronously.
• Buzzer: When this function is enabled and a radar signal is detected, there will be an alarm prompt sound.

Screen projection interface

1. Help: Instructions for Screen Projection Connection.

2. CarPlay: CarPlay screen projection on iPhones.

3. Auto: Overseas Android phone screen projection.

System Settings

• 1. Function: Click to enter. You can set tire pressure, WiFi video, audio, GPS information, time format, and Android motorcycle navigation.
• 2. Time and Date: Set the time and date manually.
• 3. Language: Multilingual Settings.
• 4. Unit of speed: Speed unit setting.
• 5. About this machine: Check the relevant information of the device.
• 6. Factory data reset: The equipment is restored to its factory condition.

The tire pressure setting interface

• 1. Bind the front wheel: After installing the tire pressure, click "Bind" to bind the corresponding ID number.
• 2. Bind the rear wheel: After installing the tire pressure, click "Bind" to bind the corresponding ID number.
• 3. Low-voltage alarm value: The current tire pressure value is displayed in real time. When it drops below the set value, the equipment pops up an alarm window.
• 4. High-voltage alarm value: The current tire pressure value is displayed in real time. When it exceeds the set value, the equipment pops up an alarm window.
• 5. Tire pressure unit: The corresponding unit can be selected according to the current shipping country.
• 6. Temperature: The unit can be set manually.

Radar rearview warning interface

1. When a vehicle appears at the left rear, the left area will turn red and flash according to the distance between vehicles. Simultaneously retrieve the rear camera and the beeping sound.

2. When a vehicle appears at the right rear, the right area will turn red and flash according to the distance between vehicles, and at the same time, the rear camera and beeping sound will be retrieved.

3. When a vehicle appears directly behind, the red boxes on both sides will flash simultaneously, and at the same time, the rear camera and buzzer sounds will be retrieved.

Radar rearview

Maximum probing distance: 20m

Maximum probing width: 9m

Measure the Angle: 75°

In terms of cycling safety guarantee, millimeter-wave radar can achieve precise rearview early warning. This radar measures the distance between the target object and the rider by transmitting and receiving millimeter-wave signals, using the propagation time of electromagnetic waves, and continuously monitors the incoming vehicles in the blind spot behind. When the Radar detects an approaching vehicle from behind, the system will automatically activate the RRV (Radar rear-view) warning mode and remind the rider through multiple warning methods:

• Visual cues: The warning lights on both sides of the vehicle's infotainment screen are flashing to ensure that cyclists can notice quickly.
• Sound instructions: The buzzer emits a sharp and highly recognizable alarm sound.
• Real-time image: The rear camera automatically turns on, providing intuitive information about the road conditions behind.

线控器按键操作 (Remote Controller Button Operation)

WiFi video APP

1. Scan the code to download motonaviAPP. Follow the operation instructions within the APP.

2. WiFi recorder

• 1. WiFi recorder: Click to enter the WiFi recorder interface. The real-time image of the current recorder can be viewed.
• 2. Recorder screen: The current real-time image display of the recorder.
• 3. Full-screen button: Click on the full screen of the recorder.
• 4. Switch button: Click to switch and view the front/rear camera images.
• 5. Stop or start the video recording: Click to control the recorder recording on/off on your mobile phone.
• 6. Sound switch: Click to turn on/off the sound recording.
• 7. Equipment album: You can view the videos/pictures recorded by the recorder.
• 8. Local album: You can view the videos/pictures that have been downloaded locally.

OTA Upgrade

1. OTA upgrade: Click to enter the OTA upgrade interface.

2. Current version: Display the current version information of the vehicle's infotainment system.

3. Upgrade: New versions can be retrieved and discovered.

Do not power off when performing an OTA upgrade. The device will automatically restart after the upgrade is completed.

Personal Center

• 1. Personal information
• 2. Equipment Management
• 3. Problem feedback
• 4. Offline map
• 5. Insurance purchase date
• 6. Version information

Product Features

Frequently Asked

1. The recorder shows that the memory is full and cannot loop the video recording.

• 1.1. First, when the new card is used for the first time on the machine, the machine will prompt you to format the TF card first. Please format it first. If there is no prompt for some, please set the format first before using it.
• 1.2. Check whether the display of the front and rear cameras is normal. If the camera display is abnormal, it will also cause no video recording.
• 1.3. Format the TF card. If you find any formatting abnormalities, you can replace the TF card and try again.

2. Automatic power on/off:

Please check whether the parking monitoring function of the machine is enabled. If this function is enabled, the machine will automatically turn on and record when it senses a collision or shaking. After recording for 15 to 30 seconds, it will automatically shut down.

3. No image when the camera is inserted:

• 3.1. Please check whether the plug is correctly connected and whether the camera cable is loose.
• 3.2. Try cross-connecting the front and rear cameras to see if they can display normally.

4. During the video recording process, the screen freezes or the key response is slow:

• 4.1. Please first check if the memory card you are using is a high-speed card (Class10). If you are using a non-high-speed card, you may encounter problems such as missing seconds, video playback lag, screen flickering, and system crashes. At the same time, since the quality of high-speed cards on the market varies greatly, when purchasing, one should choose brand memory cards.

5. Do not save after setting the time or function: When the machine experiences an abnormal power outage, the machine Settings fail to save the current data in time, resulting in the inability to save.

Disclaimer

Special note: The machine must be in a normal video recording working state before it can record video files. However, the following situations may lead to image damage or loss:

• 1. In the video recording, removing the TF card will cause the last video file to be damaged or lost.
• 2. If the power is cut off during video recording, it will cause the last video file to be damaged or lost.
• 3. Damage or loss of video files caused by destructive collisions to the machine during the video recording process.
• 4. During the video recording process, if the memory card becomes loose due to excessive collision, it may damage the video file at that time or cause the video file to be lost.
• 5. The video recorded by the dashcam is for reference only. The company will not be held responsible for any bad files or data loss caused by abnormal operation of the machine.

Notes:
This equipment is guaranteed for one year from the date you purchase the product, except for damage caused by human error or abnormal use. If there is no relevant purchase voucher, the warranty period will be implemented from the production date of the product.