High Wall Heat Pump System Submittal Data Sheet
Efficiency
| Rating | Cooling | Heating |
|---|---|---|
| SEER2 | 21.3 | - |
| EER2 | 10.8 | - |
| HSPF2-4 | - | 9.2 |
| COP | - | 3.34 |
Performance of Cooling
Rated Capacity: 12000 Btu/hr
Min/Max Capacity: 2700~13800 Btu/hr
Moisture Removal: 1.4 L/h
Standard Operating Range: 5~122°F (-15~50°C)
Conditions: Indoor: 80°F DB / 67°F WB; Outdoor: 95°F DB / 75°F WB
Performance of Heating
@ 47°F Rated: 12000 Btu/hr
@ 47°F Min/Max Capacity: 4200~14100 Btu/hr
@ 17°F Rated: 8300 Btu/hr
@ 5°F Rated: Capacity / COP: 8000 Btu/hr / 1.80
@ 5°F Max Capacity: 8000 Btu/hr
Standard Operating Range: 5~75°F (-15~24°C)
Conditions:
- Indoor: 70°F DB / 60°F WB; Outdoor: 47°F DB / 43°F WB
- Indoor: 70°F DB / 60°F WB; Outdoor: 17°F DB / 15°F WB
- Indoor: 70°F DB / 60°F WB; Outdoor: 5°F DB / 5°F WB
Indoor Specification
| Parameter | Value |
|---|---|
| Indoor Air Flow (Turbo/H/M/L/Si) | 347.3 / 294.3 / 194.2 / 153.0 / - CFM |
| Indoor Noise Level (Turbo/H/M/L/Si) | 46 / 41 / 35 / 24 / 18.5 dBA |
| Dimension (W×D×H) | 31.57 x 7.87 x 11.61 inch (802.0×200.0×295.0 mm) |
| Package: 34.45 x 11.22 x 14.96 inch (875×285×380 mm) | |
| Net/Gross Weight | 18.96 / 25.13 lbs |
| 8.6 / 11.4 kg |
Outdoor Specification
| Parameter | Value |
|---|---|
| Compressor Type | ROTARY |
| Compressor Model | KSN98D64UFZ3 |
| Refrigerant | R454B |
| Refrigerant Oil Charge | 300 mL |
| Refrigerant Oil | VG74 |
| Outdoor Air Flow (Max) | 1235.3 CFM |
| Outdoor Noise Level | 53.0 dBA |
| Dimension (W×D×H) | 30.12 x 11.93 x 21.85 inch (765.0×303.0×555.0 mm) |
| Package: 34.92 x 13.27 x 24.02 inch (887×337×610 mm) | |
| Net/Gross Weight | 59.08 / 64.37 lbs |
| 26.8 / 29.2 kg |
Electrical
| Parameter | Value |
|---|---|
| Power Supply | 208/230V, 60Hz, 1Ph |
| System MCA | 13.0 A |
| Connection Wiring | 14#x4 |
| System MOCP | 15 A |
| Compressor RLA | 7.5 A |
| Outdoor Fan Motor RLA | 0.4 A |
| Outdoor Fan Motor W | 34 W |
| Indoor Fan Motor RLA | 0.4 A |
| Indoor Fan Motor W | 30 W |
| System Power Input @ Cooling | 1111 W (220~1430 W) |
| System Power Input @ Heating | 1053 W (235~1310 W) |
| MCA (Min. circuit amps) | [See System MCA] |
| MOCP (Max. over current protection) | [See System MOCP] |
| W (Fan motor rated output) | [See Motor W values] |
Piping
| Parameter | Value |
|---|---|
| Throttle type (Indoor) | N/A |
| Throttle type (Outdoor) | Capillary |
| Liquid Size | 6.35mm (1/4in) |
| Gas Size | 9.52mm (3/8in) |
| Max. Piping Length | 82.00 ft (25 m) |
| Max. Height Difference | 49.20 ft (15 m) |
| Max. Pre-charged Length | 24.6 ft (7.5 m) |
| Refrigerant Pre-charged Amount | 24.69 oz (0.7 kg) |
| Additional Charge of Refrigerant | 0.16 oz/ft (15 g/m) |
| Connection Method | Flared |
Features
- Indoor unit TU1 copper coil
- Humidity control
- 1~100% fan speed setting
- WiFi capability: through WiFi dongle or wired controller with built-in WiFi
- OTA (by using WiFi dongle)
- Multiple control options available:
- Two way communication wired controller: 120N(X6)
- Two way communication wired controller with built-in WiFi: 120N(X6W)
- Infrared wired controller: 120L
- Wireless remote controller
- Third-Party 24V Thermostat*
*24V interface is required.
Diagram Description: Indoor Unit Dimensions
This section describes the dimensions of the indoor unit. It includes views showing the Width (W), Depth (D), and Height (H). A table lists specific dimensions for different capacities (6K~9K, 9K~12K, 18K, 18K~24K, 30K~36K) in both inches and millimeters for Width, Depth, and Height.
| Capacity | Body Code | W (inch/mm) | D (inch/mm) | H (inch/mm) |
|---|---|---|---|---|
| 6K~9K | A | 28-3/4in / 729mm | 7-7/8in / 200mm | 11-1/2in / 292mm |
| 9K~12K | B | 31-5/8in / 802mm | 7-7/8in / 200mm | 11-5/8in / 295mm |
| 18K | C | 38-1/4in / 971mm | 9in / 228mm | 12-5/8in / 321mm |
| 18K~24K | D | 42-5/8in / 1082mm | 9-1/4in / 234mm | 13-1/4in / 337mm |
| 30K~36K | F | 49-5/8in / 1259mm | 11-1/8in / 283mm | 14-1/4in / 362mm |
Indoor unit dimensions (WxH): 31.7in(806mm) x 11.65in(296mm) is also noted.
Diagram Description: Installation Instruction (Indoor Unit)
This section provides guidance on selecting the installation location for the indoor unit. It shows a diagram illustrating recommended clearances and placement. A key diagram shows a wall plate with mounting holes and dimensions: 6 inches (15cm) height, 4-3/4 inches (12cm) from the top and bottom edges. The horizontal mounting span is 70 inches (180cm). Notes indicate that the piping exit direction should be chosen based on the wall hole position relative to the mounting plate, offering four options. Another note specifies that if the gas side connective pipe is 5/8 inch (16mm) or larger, the wall hole should be 3-1/2 inches (90mm). The diagram for the indoor unit's rear shows mounting holes and dimensions (W x H), with a note regarding the gas side connective pipe size and wall hole diameter.
Diagram Description: Outdoor Unit Dimensions
This section details the dimensions of the outdoor unit. It includes front, side, and top views, indicating Width (W, W1, W3), Depth (D), and Height (H). Specific measurements are provided in inches and millimeters. A detail view (DETAIL A, SCALE 1:2) shows connection points and dimensions (A, B, C, D, R5).
| View | Dimension | Value (inch/mm) |
|---|---|---|
| Front/Top | W3 | 30-7/8in / 784mm |
| Front/Top | W | 30-1/8in / 765mm |
| Front/Top | W1 | 32-7/8in / 835mm |
| Front/Top | A | 17-3/4in / 452mm |
| Side | D | 11-7/8in / 303mm |
| Side | H | 21-7/8in / 555mm |
| Side | C | 12-3/8in / 314mm |
| Side | B | 11-1/4in / 286mm |
| Side | 3/4in (18mm) | [Dimension reference] |
| Side | 3in (76mm) | [Dimension reference] |
| Side | 1-1/4in (32mm) | [Dimension reference] |
| Detail A | R5 | 2-3/8in (61.6mm) |
Diagram Description: Installation Instruction (Outdoor Unit)
This section outlines the installation clearance requirements for the outdoor unit. Diagrams show recommended spacing from walls and other obstructions. Clearances are indicated with arrows and text:
- 20 inches (500mm) or more when front and sides of the unit are clear.
- 4 inches (100mm) or more on the sides.
- 14 inches (350mm) or more on the rear.
- 20 inches (500mm) or more when any 2 sides of left, right, and rear of the unit are clear.
