Hoffen CSI-8307 Cordless Steam Iron User Manual

1. Intended Use

The Hoffen CSI-8307 cordless steam iron is designed for ironing fabrics to remove wrinkles. With a power rating of 2000-2400 W, it offers convenient and efficient operation. The steam burst function effectively tackles stubborn creases, and the iron can be used for vertical steaming. It features a detachable base for cord-free ironing. This appliance is intended for domestic use only and not for industrial or commercial purposes. Following these instructions ensures safe installation and use.

2. Technical Specifications

3. Important Safeguards

1. This appliance may be used by children aged 8 years and above, and by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, provided they are supervised by an adult or instructed in the safe use of the device and understand the hazards involved.
2. Children must not play with the device.
3. Cleaning and maintenance must not be performed by children unless supervised by an adult.
4. Keep the steam iron and its power cord away from children under 8 years old when the iron is connected to the mains or cooling down after use.
5. Never leave the iron unattended when connected to the electrical mains.
6. Before filling the water reservoir or emptying residual water, always disconnect the iron from the mains.
7. The water inlet cover must not be open during use. Fill the water reservoir as described in section 7.2.
8. Use the iron only with the supplied base.
9. When placing the iron on its base, ensure the base is on a stable surface.
10. If the power cord is damaged, it must be replaced by the manufacturer, a service centre, or a qualified person to avoid hazards.
11. The iron must be used and placed on a stable, flat surface.
12. Do not use the iron if it has been dropped, shows signs of damage, or is leaking water.
13. Read the entire instruction manual before use.
14. Warning! Never touch the hot soleplate when the iron is on – risk of burns!
15. Warning! Do not touch hot metal parts, hot water, or steam to avoid burns or scalding.
16. It is recommended to use distilled and/or demineralised water in the water reservoir where possible.
17. Exercise particular caution when children are present near the device.
18. Do not immerse the device, its power cord, or plug in water or other liquids. Take special care when pouring water into the reservoir.
19. Do not touch the device with wet hands.
20. Never direct the steam jet at other people or animals.
21. Never direct the steam jet directly at electrical devices or devices containing electrical components (e.g., TV, radio, electric heater).
22. Do not direct the steam jet at unprotected wooden surfaces, unsuitable grout, cold glass, or plastics.
23. Never turn the device upside down or lay it on its side when it is switched on or when there is water in the reservoir.
24. Caution! Risk of burns! The soleplate heats up significantly during use.
25. Exercise caution when emptying the water reservoir – risk of scalding with hot water.
26. Use the device only for its intended purpose.
27. Keep the instruction manual; keep the packaging if possible.
28. If the device is passed on to another person, ensure this instruction manual is included.
29. Do not use the iron if it is damaged or malfunctioning.
30. To avoid the risk of fire or electric shock, observe basic safety precautions when using electrical appliances, especially in the presence of children.
31. The device is intended for household use only. Do not use it for any other purpose.
32. Before use, carefully unwind the mains cord.
33. Ensure the mains cord does not touch the hot soleplate.
34. After use, turn off the iron, disconnect it from the mains, and place it upright. Caution! The iron will remain hot for some time.
35. Remove the plug from the mains socket when the device is not in use or before cleaning. Allow the device to cool down before cleaning.
36. Do not cover the device during operation. If covered or in contact with flammable material, there is a risk of fire.
37. Never steam-iron or dry-iron clothes while they are being worn, or direct steam at people.
38. Do not put fragrances, vinegar, or other chemicals into the water reservoir, as they can cause serious damage to the device.
39. Monitor the water level in the reservoir. Too much water may spill out during ironing; too little water may prevent the steam burst function from working.
40. Do not immerse the device in water or any liquid.
41. Do not touch the soleplate while ironing or immediately afterwards, as it is hot.
42. Do not wind the cord around the iron or base before it has completely cooled down.
43. Do not attempt to disassemble any parts of the device. The device contains no user-serviceable parts.
44. Burns can result from touching hot parts of the iron, and scalding from contact with hot water or steam. The iron's water reservoir may contain hot water, which may leak if the iron is turned upside down.
45. Do not open the water inlet cover while ironing.
46. Retain this user's manual.
47. To obtain an electronic version of the user's manual, send a message to: infolinia@vershold.com.

4. Explanation of Symbols

• ? Read this instruction manual
• CE Product compliant with the requirements of applicable EU directives
• ?️ Disposal of waste electrical and electronic equipment – see the DISPOSAL section of this manual.
• ? Indoor use only.
• R Trademark indicating that the manufacturer has contributed financially to the construction and operation of a packaging material recovery and recycling system.
• 20 PAP Designation of the packaging material – cardboard.

5. Overview

The diagram below illustrates the components of the Hoffen CSI-8307 Cordless Steam Iron:

• 1. Spray nozzle
• 2. Water inlet cover
• 3. Steam adjustment knob
• 4. Steam burst button
• 5. Spray button
• 6. Iron heating/power supply LED indicator
• 7. Handle
• 8. Rotary power cord connection
• 9. Recharging base attachment/release lock
• 10. Recharging base with power cord
• 11. Rear cover
• 12. Water reservoir
• 13. Temperature control knob
• 14. Maximum water level mark
• 15. Cleaning function button "CLEAN"
• 16. Ceramic soleplate
• 17. Measurement cup

6. Set Contents

The package includes:

• 1 x Iron
• 1 x Recharging base with power cord
• 1 x Measurement cup
• 1 x User's manual

Open the packaging carefully and check that all components are present and undamaged. If any part is damaged or missing, contact the dealer and do not use the product. Keep the packaging or dispose of it according to local regulations.

Caution! For the safety of children, do not leave packaging materials (plastic bags, cardboard boxes, Styrofoam, etc.) accessible and unattended. Risk of suffocation!

7. Use

7.1 Before First Use

CAUTION! The iron may emit smoke during the first use. This is normal and does not indicate damage. Ensure the iron is used in a well-ventilated area. The smoke should stop after a short while. If smoke persists, unplug the iron immediately.

7.2 Filling the Water Tank

CAUTION!

• Do not place any objects in the water reservoir.
• Do not add water while ironing or when the iron is hot.
• The device can be filled with tap water. However, if your local water is hard, using distilled or demineralised water is recommended.

1. Ensure the iron is unplugged from the mains.
2. Open the water inlet cover on the front of the iron.
3. Fill the water reservoir using the included measuring cup, not exceeding the maximum level indicated on the side of the iron.
4. Close the water inlet cover.

7.3 Placing the Iron on the Base / Removing the Iron from the Base

1. Ensure the device is switched off (temperature control knob set to OFF) and unplugged.
2. To detach the iron from its base, move the base release lock towards the unlocked padlock icon (?) and lift the iron off the base.
3. To reattach the iron to its base, ensure the base attachment/release lock is in the unlocked padlock position (?), then place the iron on the base.
4. Next, move the base lock towards the locked padlock icon (?) to secure the iron to its base.
5. Once the iron is attached and locked to the recharging base, connect the iron to the power outlet and set the temperature control knob to the desired heating position.

CAUTION! When removed from the base, the iron will gradually cool down. A cordless iron can only retain heat; it cannot generate heat when off the base as it has no internal power source (like batteries).

7.4 Operation

For steam ironing, fill the water reservoir as described in section 7.2 before turning on the iron. Water may remain in the reservoir during dry ironing. For the iron to heat up and the indicator light to turn on, the temperature control knob must be set at least to the 'synthetic' position (indicated by a single dot •).

CAUTION! Water leaking from the soleplate during steam ironing indicates insufficient heating. Set the temperature control knob to a higher value. Steam will be emitted once the device reaches the required temperature.

7.5 Dry Ironing

1. Place the iron upright.
2. Ensure the iron is correctly attached to the recharging base and the base lock is in the locked padlock position (?).
3. Set the steam adjustment knob to the (??) (no steam) position.
4. Connect the power cord plug to a grounded electrical outlet.
5. Set the desired ironing temperature by rotating the temperature control knob to the selected position.

CAUTION! Water may remain in the water reservoir during dry ironing. CAUTION! Before ironing, check the laundry care label for the required ironing temperature.

If you are unsure of the fabric type, determine the correct temperature by ironing a small, hidden part of the garment first.

CAUTION! Always start ironing with garments requiring the lowest temperature.

6. When the iron heating indicator light is on, the iron is connected to the power source and heating up to the set temperature.
7. When the light goes off, the iron has reached the desired temperature.

7.6 Spray Function

This function is used to remove stubborn creases. To moisten the fabric, press the spray button (?) several times. Water will be dispensed from the spray nozzle at the front of the iron.

7.7 Steam Burst Function

This function is useful for removing creases on hanging clothes, curtains, etc. It can also be used during dry ironing. CAUTION! Never direct the steam at people!

1. Ensure there is enough water in the reservoir (refer to section 7.2 if needed).
2. Place the iron upright.
3. Set the temperature control knob to at least the 'silk wool' setting (••).
4. Connect the power cord plug to a grounded electrical outlet.
5. The indicator light will turn on and will go off when the iron reaches the desired temperature.
6. Aim the soleplate at the fabric and press the steam burst button (?).

7.8 Steam Ironing

1. Ensure there is enough water in the reservoir (refer to section 7.2 if needed).
2. Place the iron upright.
3. Set the temperature control knob to at least the 'wool' setting (••).
4. Set the steam burst control to one of the three selectable steam power settings.
5. Connect the power cord plug to a grounded electrical outlet.
6. The indicator light will turn on and will go off when the iron reaches the desired temperature.
7. The iron will emit steam only when in a horizontal position.
8. After finishing steam ironing, move the steam burst control to the (??) (no steam) position.

7.9 After Ironing

1. Place the iron on its base in the upright position and set the lock to the locked padlock icon (?).
2. Unplug the iron from the power source.
3. Wait for it to cool down.
4. Empty the water reservoir.
5. Store in a dry, well-ventilated place.

CAUTION! If the thermostat fails, a thermal protection mechanism will prevent the iron from overheating.

8. Cleaning and Care

8.1 General Rules

Proper and regular cleaning ensures safe operation and extends the lifespan of the device.

Warning! Proper and regular cleaning will ensure safe operation and extend the lifespan of the device.

1. When finished, turn off and disconnect the device from the power source.
2. Wait approximately 30 minutes for the device to cool down.
3. Empty the water tank.
4. If necessary, wipe the device components dry with a soft cloth.
5. Store in a safe place.

Cleaning

1. Before cleaning, wait for the iron's soleplate to cool down.
2. Wipe the iron soleplate and housing with a damp cloth.
3. Never use caustic or abrasive cleaning agents.
4. Do not use vinegar, chlorine, or other chemical compounds for cleaning.

Caution! Do not clean the device with strong chemicals, alkaline, abrasive, or disinfecting agents, as they may damage the surface. Do not use metal, sharp, or rough cleaning accessories, as they may damage the surface!

Do not immerse the iron or power cord in water or other liquids.

Self-Clean Function

1. Connect the steam iron to the mains, with the power cord base attached.
2. Add water to the reservoir until it is half full.
3. Set the temperature control knob to "MAX".
4. Wait for the iron to reach the desired temperature – the heating LED will go off.
5. Disconnect the iron from the mains.
6. While holding the iron horizontally over a sink, move the steam control to the "MAX" position and press the “CLEAN” button. Boiling water and steam will be emitted, washing out dirt from the soleplate openings.
7. After the iron has cooled down, place it (preferably) on an old piece of fabric to keep the soleplate dry during storage.

Anti-Calc Function

ATTENTION! Despite using the ANTI-CALC function, it is still recommended to use distilled and/or demineralised water.

9. Repair

The device contains no user-serviceable parts. Do not attempt repairs yourself; always use a specialist. If the power cord is damaged, it must be replaced by the manufacturer, service centre, or a qualified person.

10. Storage and Transport

• Wait until the iron cools down.
• Empty the water reservoir.
• Wind the cord around the iron.
• Store the empty iron upright on a stable surface, with the base attached.
• Always keep the iron in a dry, well-ventilated location inaccessible to children.
• Protect the device against vibration and shock during transport.

11. Disposal

All packaging materials are 100% recyclable and labelled accordingly. Dispose of packaging in accordance with local regulations. Keep packaging materials out of children's reach, as they can pose a hazard.

Correct disposal of the device:

1. According to the WEEE Directive (2012/19/EU), the crossed-out wheelie bin symbol (?️) is used to label electrical and electronic devices requiring segregation.
2. Do not dispose of the product with domestic waste. Hand it over to an electric and electronic devices collection and recycling point. The symbol on the product, manual, or package indicates this requirement.
3. Plastics in the device can be recycled according to specific markings. Recycling contributes significantly to environmental protection.
4. Information on collection points for electric and electronic devices is available from local government agencies or the dealer.

12. CE Declaration

The device has been designed, manufactured, and marketed in compliance with the Low Voltage Directive and the EMC Directive. It bears the "CE" mark and has a declaration of conformity available for market supervision agencies.

13. Warranty

To submit a complaint, deliver the device to the Customer Service Point at any Biedronka store. For questions or issues related to product operation, contact infolinia@vershold.com or call +48 667 090 903.

Your opinion is important. Evaluate the product at www.vershold.com/opinie.

The warrantor grants a 36-month warranty from the date of purchase. Report any defects at the point of purchase.

A damaged product fails to provide features described in the manual due to intrinsic properties. The beneficiary must deliver the appliance to the Customer Service Point with proof of purchase and a detailed description of the defect.

The warranty excludes physical damage not caused by the manufacturer/distributor, damage from incorrect usage, or force majeure. It also excludes products with removed tamper-proof seals, or those with attempted repairs or modifications. Components subject to natural wear and tear are not covered.

It is recommended to submit the complete product for service. This warranty does not exclude or restrict buyer's rights under Polish Civil Code provisions regarding warranties for defects.

The warranty is applicable within the Republic of Poland.

Manufacturer (Warrantor): ERESHOLD POLAND Sp. z o.o., ul. Żwirki i Wigury 16A, 02-092 Warszawa, Poland. Made in China.