FK Irons Flux Max User Manual

Safety Notice

The Flux Max is a Class III appliance, designed to be supplied from a separate/safety extra-low voltage (SELV) power source. The voltage from a SELV supply is low enough that, under normal conditions, a person can safely come into contact without the risk of electrical shock. Extra safety features built into Class I and Class II appliances are not required. For medical devices, compliance with Class III is not considered sufficient protection, and further, more-stringent regulations apply to such equipment.

Technical Data

Barrier Protecting Your Machine

FK Irons strongly suggests the use of barrier products to protect the machine. For a visual demonstration of barrier protection methods, please visit the FK Irons YouTube channel.

This device is only for use by trained tattoo artists and not for use by children or persons of reduced physical, sensory or mental capabilities.

Introduction

Flux Max

Take your skills to the max with the ultimate tool. The Flux Max offers more control, more convenience, and more innovation.

Overview

Specifications

• Output Voltage: 4-12V
• Increment/decrement voltage interval: 0.5 or 0.1V*
• Maximum output current: 1A
• Charger Input: USB-C
• Size: H 124.5mm x W 38.5mm
• Weight: 205g (7.23oz)
• Battery Life: ~ 6-10 Hours (based on operating parameters)

Features

The PowerBolt II

Battery Charge: 4 bars = 100%, 3 bars = 75%, 2 bars = 50%, 1 bar = 25%. A single bar blinking indicates approximately 5 minutes of operation remaining.

Note: The screen switches to sleep mode after 15 seconds of inactivity. Press the power button to wake the screen.

Charging: When USB-C is plugged in, the screen mode will show battery charging status. For best results, use the provided charging cable.

Modes Menu

Hold the power button (center button) for 3 seconds to display the built-in menu. Keep holding the power button to cycle through menus; release to stay on a chosen screen.

• eGive: Use the up and down buttons to select level. Level 0 = disabled, Level 1 = Hard, Level 2 = Medium, and Level 3 = Soft. When changing eGive, allow the machine to finish sensing the needle before use.
• Footswitch: On/Off selection is made with the Up/Down buttons. The Killswitch remains connected until the user disconnects it in the PowerBolt II menu.
• Timer: Start/Stop is selected with the Up/Down buttons. The timer operates from 0-24 hours in one-minute intervals. Once the timer is stopped, it resets to zero.
• Display: Use the Up/Down buttons to select Voltage or Hertz as the main power display.
• Voltage: Use the Up/Down buttons to select increments of 0.1 or 0.5 Volts.
• Screen Orientation: Use the Up/Down buttons to select left or right-hand operation.
• Battery Disconnect: Use the Up/Down buttons to select Cancel/Off. To reactivate the PowerBolt II, plug into any USB-C port.
• Device Reset: Hold the Up and Down buttons at the same time.

Detaching the PowerBolt II

The PowerBolt II is compatible with the Flux Max, Flux, FluxS, and the EXO. To detach your PowerBolt II, ensure you have a firm grip on the body of the Flux or EXO and the Grip. Turn the PowerBolt II counter-clockwise and pull out. To attach the PowerBolt II, push in while twisting clockwise. Ensure the lock mechanism moves freely. The PowerBolt II must sit correctly to ensure power electric leads align properly. Avoid contact with the PowerBolt II leads while recharging or servicing. Turn power off before removing the battery from the machine.

Connecting Your Machine

How to Charge Your Machine

Insert the provided USB-C cable into the back of the PowerBolt II and connect to a Hover or power socket. Make sure the cable is properly seated and is fully inserted into the PowerBolt II. The PowerBolt II is not designed to operate while plugged in.

The USB-C connection is intended only for charging your PowerBolt II. The PowerBolt II can be recharged while not attached to the Flux Max. If connecting to a Hover, the charge speed will be up to 1.0 A.

Adjusting Needle Depth

To adjust needle depth, hold the machine body and PowerBolt II while turning the Grip. A counter-clockwise turn decreases depth, while a clockwise turn increases depth (also known as needle hang). Each time you turn the grip, you can feel the tactile feedback of the ratcheting mechanism. Each "click" displaces your needle 0.2 mm and allows you to set your needle precisely without involuntarily turning while tattooing.

Additional Information

Voltage Parameters

While voltage is a parameter that will vary from artist to artist, the PowerBolt II has been tested to operate at a minimum voltage of 4 Volts to a maximum voltage of 12 Volts. Depending on the type of needle configuration, or brand you use, feel free to adjust the voltage to obtain the desired performance.

Warranty

Darklab warrants that the device will perform efficiently when used as intended. Should this product prove to be defective due to manufacturing issues, Darklab will repair/replace the device free of charge. This warranty will be void if the device shows signs of having been tampered, disassembled, handled roughly, dropped, overexposed to moisture, or damage resulting in compromised functionality.

Handy Tips

• Do not exceed the suggested voltage.
• Use only FDA-approved cold sterilization solutions for disinfection.
• NOT AUTOCLAVABLE.

Troubleshooting

1. Machine Manufacturer: FK Irons: 1771 NW 79th Avenue, Doral, Florida 33126.
2. Servicing Your Machine: As for any mechanical device, FK Irons strongly suggests that you service your device once a year to ensure all working parts are working as expected. This ensures the optimal condition of all working parts, including internal machine clean up and fresh lubrication. Routine servicing will ensure that your machine remains functioning as intended. Service is subject to fees.
3. Warning: Disconnect machine from any power source before making any adjustments.

For service inquiries, please contact service@FKirons.com. For additional tips and tutorials, please visit Youtube.com/FKirons.