Product Overview
This manual provides instructions for the VEVOR CW02 Hitch Cargo Carrier. VEVOR is committed to providing tools with competitive prices. Please note that savings claims are estimates and may vary compared to other brands.
Safety & Warnings
⚠️ Read and understand this entire manual before assembling, installing, operating, or servicing this product. Failure to follow these warnings and instructions can cause death, personal injury or damage to valuable property.
- Adhere to all Department of Transportation (D.O.T.) requirements when using this product. Use ropes and tie downs (not included) to securely hold all cargo in place.
- For the vehicle that will support the Cargo Carrier, read all pertinent vehicle instructions and warnings provided in the owner's manual. Make sure the vehicle's engine is OFF, with parking brake set, before loading or unloading the Cargo Carrier.
- This Cargo Carrier must be attached to a 2"x2" Class III or Class IV hitch receiver. The hitch must be properly installed by a qualified service technician and be certified to support the weight of this Cargo Carrier and its contents.
- This Cargo Carrier is designed to haul firewood, coolers and other similar loads. Do not modify the Carrier and do not use this product for purposes that it was not designed for.
- Do not overload the Cargo Carrier. Never exceed the maximum weight capacity.
- When assembly is complete, check and test all vehicle systems including lights and brakes; make sure no damage occurred during product installation.
- Frequently check the condition of the Cargo Carrier and the vehicle's hitch receiver. Make sure all components are in good condition. If the Cargo Carrier or hitch receiver become damaged through accident, or if any weld damage is noted, the product should be replaced. Check to make sure that all hardware is tightly secured in place. Keep the Cargo Carrier clean.
- Use common sense when working. Stay alert and concentrate when setting up and using the Cargo Carrier. Never work while under the influence of alcohol, drugs or medications.
- While assembling and using the Cargo Carrier, keep the work area clean and well lighted. Keep spectators and children out of the work area.
- Dress appropriately. Never wear loose fitting clothing or jewelry when working. Contain long hair, and keep hair, clothing and gloves away from moving parts.
- Be aware of the danger of "dynamic loading". This situation arises when a load is dropped onto the Carrier, resulting in a short term excessive load. Dynamic loading can result in damage and failure of the Carrier and/or hitch receiver, and personal injury to the person loading the Carrier.
- Never load people or animals into the Cargo Carrier.
- Weight inside the Cargo Carrier should be evenly distributed, with heavier items positioned towards the center of the Carrier.
- Note the position of the vehicle's exhaust pipes before setting up the Cargo Carrier. Make sure exhaust pipes are not in close proximity of the Cargo Carrier; flammable goods in the Cargo Carrier could catch on fire due to heat from the exhaust. If this risk exists on your vehicle, do not use the Cargo Carrier.
- Do not ride in vehicle being loaded or unloaded. Load and unload vehicle slowly, according to manual instructions.
Specifications
| Model Series | Maximum Load Capacity (lbs) | For Use With | Cargo Basket Dimensions (mm) | Gross Weight(kg) | MEAS(mm) |
|---|---|---|---|---|---|
| CW02 | 400 | 2" x 2" Class III and IV Hitch Receivers | 1524×610×356 | 28.2 | 1575×635×145 |
Package Contents
The package contains the following components:
- Part 1: Rear Long Frame (1 pc)
- Part 2: Short Frame (2 pcs)
- Part 3: U-shaped Lock Ring (1 pc)
- Part 4: Nut M10 (7 pcs)
- Part 5: Washer (7 pcs)
- Part 6: Support Rod (1 pc)
- Part 7: Reinforcing Plate (2 pcs)
- Part 8: Bolt M10×70 (2 pcs)
- Part 9: Rotating Seat (1 pc)
- Part 10: Bolt M10×20 (4 pcs)
- Part 11: R pin φ4.0 (1 pc)
- Part 12: Hook Stabilizer (1 pc)
- Part 13: Base Frame (4 pcs)
- Part 14: Front Long Frame (1 pc)
- Part 15: Rotary Bolt φ16*90 (1 pc)
- Part 16: R pin φ1.5 (4 pcs)
- Part 17: R pin φ2 (1 pc)
- Part 18: Rotary Bolt φ10*75 (1 pc)
- Part 19: Rotary Bolt φ8*50 (4 pcs)
- Part 20: Bolt M10×75 (1 pc)
- Part 21: Nut M8 (2 pcs)
Installation Guide
Follow these steps to install the hitch cargo carrier:
- Flip the cargo carrier over. Attach the Support Rod (6) to the cargo carrier using the Reinforcing Plate (7), Bolt (10), Bolt (8), Washers (5), and Nuts (4). Ensure all hardware is securely tightened.
- Attach the Rotating Seat (9) to the Support Rod (6) with Bolt (20), Nut (4), R pin (17), and Rotary Bolt (18).
- To place the cargo carrier on the vehicle's hitch receiver:
- With a helper, lift the empty cargo carrier and insert the Rotating Seat (9) into the vehicle's hitch receiver.
- Align the holes on the Rotating Seat (9) and the vehicle's hitch receiver. Insert the Rotary Bolt (15) into the aligned holes and secure it with the R-pin (11).
- Stand the frames (1, 2, 14) up. Align the holes on Frame (1) and Frame (2) and insert the Rotary Bolt (19). Secure with R-pin (16).
- Load the cargo carrier as needed. Use ropes and tie downs to securely hold all cargo in place.
- When the cargo frame is empty, you can pull out the Rotary Bolt (18) to flip the entire cargo frame 90 degrees. Insert Rotary Bolt (18) into the upper holes of the Rotating Seat (9) and secure with R-pin (17).
Support & Warranty
For technical support and E-Warranty information, please visit: https://www.vevor.com/support
This product is Made In China.
Contact Us â Official VEVOR Support
