Schuberth SC Edge Quick Start Guide

Product Approval

The SC Edge is approved according to ECE 22.06 for the following SCHUBERTH helmets:

Product Identification:

• Serial number / Batch number
• Approval number acc. ECE 22.06: 0610631-YYYY-ZZZZ-SAcc
• SC EDGE
• MODEL: XXXXXXXX
• FCC ID: Q95ER32
• IC: XXXXXXXXXX
• Cardo Systems, Ltd.
• 5V ⎓ 1.0A
• Certifying authority
• Sequential number

Cardo Connect App

Download the Cardo Connect App for enhanced functionality:

• App functions: Mesh Intercom, Bluetooth Intercom, Music, Device settings, Language settings, Voice Commands List.

Scan the QR codes to download the app or access the User's Guide.

A full version of the user's guide can be downloaded from: cardosystems.com/pages/support/sc-edge

Product Details

SC EDGE

Controls:

• Power & device pairing button: [power-symbol] button
• Status LED: Indicates device status.
• LED Indicator: Shows different states (colors may vary).
• Reset: [reset-symbol] button
• USB Charging port: For charging the device.

SC EDGE Remote Control

• (+) Button: Increases volume or navigates forward.
• (-) Button: Decreases volume or navigates backward.
• Media: Controls media playback.
• Intercom Button: Initiates intercom functions.
• Battery Slot: Holds the battery.
• Battery Release Hole: For releasing the battery.

Installation

Inserting the Battery

1. Insert the battery into the designated slot.
2. The unit also supports CR 2025 or CR 2016 batteries.

Installing the SC EDGE Remote Control

1. Attach the cover for the SC EDGE Remote Control.
2. Slide the remote control into place.

Installing the SC EDGE

1. Align and insert the SC Edge unit into the helmet mount.
2. Connect the single connector. Ensure it clicks into place (1x click).
3. Align and insert the SC Edge unit.
4. Ensure the unit is securely attached (1x click).

Removing the SC EDGE

1. Release the SC Edge unit from the helmet mount.
2. Disconnect the connectors by wiggling and pulling gently.
3. Clean the communicator with a soft, lint-free cloth dampened in an electronic-safe solution. Avoid abrasive materials and ensure the device is powered off before cleaning.

Installing the Microphone

Note: The microphone is pre-installed on the S3 helmet.

1. Install the microphone by pressing firmly on the area marked with the orange circle.
2. Position the small triangle towards the mouth for optimal voice capture.

Getting Started

The SC Edge and SC Edge Remote Control are pre-paired. They will automatically connect when powered on.

• Power On: Tap the [power-symbol] button once.
• Power Off: Tap the [power-symbol] button once.
• Wake Up: Press any button on the remote control. The remote enters sleep mode after 2 hours of inactivity.

Basic Operations

Power Off - Remote

Press and hold the [power-symbol] button for 5 seconds.

Phone Pairing

Step 1: Initiate pairing mode on the SC Edge (LED Red & Blue).

Step 2: On your smartphone, search for "SC EDGE" via Bluetooth and connect.

Cardo Connect App

• Download: Available on the App Store and Google Play.
• Register: Create an account within the app.
• Choose Language: Select your preferred language.
• Update Software: Keep your device firmware up-to-date.

Device Pairing (GPS/Bike/Phone)

Step 1: Initiate pairing mode on the SC Edge (LED Red & Blue).

Step 2: Pair with GPS, Phone 1, Bike, or Phone 2 by following the on-screen instructions and tapping the respective buttons.

• Stop Phone: Press and hold the [power-symbol] button for 2 seconds.
• Volume Up: Tap the (+) button once.
• Volume Down: Tap the (-) button once.
• Mute / Unmute Microphone: Tap the (+) and (-) buttons simultaneously once.
• Voice Assistant: Activate Siri or Google Assistant by saying "Hey Siri" or "OK Google".

Radio Functions

Set Presets

1. Use the Cardo Connect App to set radio presets.
2. Access FM radio through the app.

• On: Press the (+) button twice.
• Off: Press and hold the (+) button for 2 seconds.
• Next Preset: Tap the (+) button once.
• Previous Preset: Tap the (-) button twice.
• Auto tune: Press and hold the (+) and (-) buttons for 2 seconds.

Music Functions

• On: Tap the (+) button once.
• Off: Press and hold the (+) button for 2 seconds.
• Next: Tap the (+) button once.
• Previous: Tap the (-) button twice.
• Mute audio: Tap the (+) and (-) buttons simultaneously once.
• Unmute audio: Tap any button.

Sharing Features

Set Sharing Partner

1. Follow the app instructions to set a sharing partner.
2. Start or stop sharing by pressing and holding the (+) and (-) buttons for 2 seconds.

Switch Source

• Music to Radio: Press and hold the (+) and (-) buttons for 5 seconds.
• Radio to Music: Press and hold the (+) and (-) buttons for 5 seconds.

Phone Calls

• Answer incoming call: Tap the (+) button once or tap the (-) button once.
• Ignore incoming call: Tap the (-) button once.
• End Call: Tap the (+) button once or tap the (-) button once.
• Speed dial (predefined number): Tap the (+) button three times.

DMC Intercom

• Grouping: Press and hold the (+) and (-) buttons for 5 seconds. LED turns Purple upon successful grouping.
• Stop Grouping: Press and hold the (+) and (-) buttons for 2 seconds.
• Mute / Unmute group: Press and hold the (+) and (-) buttons for 2 seconds.
• Share call: Press and hold the (+) and (-) buttons for 2 seconds.
• Start / Stop Private Chat: Tap the (+) button twice.
• Connect / Disconnect Bluetooth passenger to DMC: Tap the (+) button three times.

Switch source

• DMC to Bluetooth®: Press and hold the (+) and (-) buttons for 5 seconds.
• Bluetooth® to DMC: Press and hold the (+) and (-) buttons for 5 seconds.

Bluetooth Intercom

Pairing

Pair to Rider A: Press and hold the [power-symbol] button for 5 seconds (LED Red).

Pair to Rider B: Press and hold the [power-symbol] button for 5 seconds (LED Red), then tap the (+) button once (LED Blue).

Return to Rider A: Tap the [power-symbol] button once.

• Stop Intercom pairing: Press and hold the [power-symbol] button for 2 seconds.
• Share / Stop phone call: Press and hold the [power-symbol] button for 2 seconds.
• Call/End Intercom (for both Rider A&B): Tap the [power-symbol] button once.

Troubleshooting

• Reboot: Press and hold the [power-symbol] button for 5 seconds.
• Factory Reset: Press and hold the [power-symbol] button for 10 seconds. This will delete all pairings and user settings. Alternatively, perform a factory reset through the Cardo Connect App.

Caution: The small hole is a microphone. Do not insert any sharp objects.

Voice Commands - Always On!

• Calls: Answer, Ignore, "Hey Cardo, end call", "Hey Cardo, speed dial", "Hey Cardo, redial number".
• Music: "Hey Cardo, music on", "Hey Cardo, music off", "Hey Cardo, next track", "Hey Cardo, previous track", "Hey Cardo, share music".
• Radio: "Hey Cardo, radio on", "Hey Cardo, radio off", "Hey Cardo, next station", "Hey Cardo, previous station".
• Intercom (Bluetooth only): "Hey Cardo, call intercom", "Hey Cardo, end intercom".
• Voice Assistants: "Hey Siri", "OK Google".
• Volume: "Hey Cardo, volume up", "Hey Cardo, volume down".
• Microphone: "Hey Cardo, mute audio", "Hey Cardo, unmute audio", "Hey Cardo, mute microphone", "Hey Cardo, unmute microphone".
• Battery: "Hey Cardo, battery status".

Contact Information

Manufacturer: Cardo Systems Ltd., 101 E. Park Blvd., Suite 600 Plano, TX 75074, USA.

Importer in Europe: SCHUBERTH GmbH, Stegelitzer Strasse 12, 39126 Magdeburg, Germany

Importer in UK: Tran Am Ltd, William House, Gore Road GB BH25 6RJ New Milton Hants

Importer in US: SCHUBERTH North America, 9920 Pacific Heights Blvd., Suite 150, San Diego, CA 92121

Subject to change. No liability accepted for mistakes and print errors.

Visit: WWW.SCHUBERTH.COM