Aigostar LED Ceiling Fan with Light - Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

• To prevent fire and electric shock accidents, it is prohibited to install and use electrical switches that are not configured for this ceiling fan.
• Please disconnect the power supply before maintenance or cleaning to avoid personal injury accidents.
• ⚠️ Warning: Electric shock danger!
• This product is not waterproof. Please use it in a dry indoor environment.
• The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.

SPECIFICATIONS

This product contains a light source of energy efficiency class <E>-(EU)2019/2015.

INSTALLATION

1. Take out the B-shaped clip and pull out the latch.
2. Thread the motor wire and light wire into the boom. Corresponding to the boom and head holes, and insert the latch. Type B clamp is inserted into the latch hole. Lock the head screws.
3. Place the decorative cover, top the cover.
4. Ensure secure installation on wood or concrete ceilings.
5. Connect the receiver and wiring according to the labels.
6. Pre-lock two screws on the hanger in advance, then screw on the suspension bell, and finally tighten the screws.

Instruction for remote control

The remote control has various functions:

1. LED light on/off switch
2. Fresh air mode for fan - press button 10 (Fan on/off switch) and then button 2 to enter fresh air mode
3. Increase LED light brightness
4. Decrease LED light color temperature
5. Decrease LED light brightness
6. Set timer for 1 hour
7. Fan speed 1 - press after turning on the fan to operate at speed 1
8. Fan speed 2 - press after turning on the fan to operate at speed 2
9. Fan speed 3 - press after turning on the fan to operate at speed 3
10. Fan on/off switch
11. Fan forward/reverse switch
12. Night light mode - press to enter night light mode
13. Increase LED light color temperature
14. Set timer for 2 hours
15. Set timer for 4 hours
16. Cancel timer
17. Fan speed 4 - press after turning on the fan to operate at speed 4
18. Fan speed 5 - press after turning on the fan to operate at speed 5
19. Fan speed 6 - press after turning on the fan to operate at speed 6

Note:

• Open the battery cover of the remote control, install two 1.5V AAA batteries, and close the battery cover.
• If the remote control is not used for a long time, please remove the batteries.

CLEANING AND MAINTENANCE

• It is recommended to check the connection parts of the fan at least once a year, such as the cross pin, blade bracket, ceiling plate, connecting screws, and fan blades, to ensure that the product connection is still safe and reliable. (The shelf life of the fan blades is two years. Please replace them after two years.)
• Regularly clean the ceiling fan to keep the surface clean and bright. When removing surface dust, please use a soft brush or cloth to avoid damaging the surface. When removing oil stains or deposits, you can wipe them with a slightly damp cloth, but do not rinse with water.
• Please do not add lubricating oil to the ceiling fan motor, as the motor bearings come with lubricating oil.

TROUBLESHOOTING

Common issues to check for troubleshooting the fan include:

1. Check if the fuse in the external power supply line is blown or if the automatic protection switch is tripped, which may cause a short circuit and prevent the fan from starting.
2. Check if the voltage is significantly lower than the rated voltage of the fan (the fan requires a voltage above 176V to start).
3. Check if there is any loose or poor contact in the internal wiring of the fan.

Note: If the above three checks fail to identify the problem, please contact a professional repair person for assistance.

To ensure the fan works properly, please also:

1. Avoid severe impact on the fan during installation.
2. Ensure that the fan blades and blade brackets are securely installed without any looseness.
3. Ensure that the ceiling plate and downrod are correctly installed, and do not remove the shock-absorbing rubber on the ceiling plate.
4. Allow a 24-hour trial period for new fans, during which most of the noise should disappear.
5. Avoid installing the fan on wooden ceilings, steel structures, or prefabricated panels, as this may amplify the noise.
6. Check if the connection wires of the light kit are loose.
7. Check if the light switch is damaged, if the wire ends are loose, or if there is poor contact at the wire terminals.
8. Check if the replaceable light bulb is burnt out.