GIGABYTE AI TOP 100 Z890 Premium Gaming & AI Empowered Desktop PC

Table of Contents

• Parts Checklist

• Chapter 1 Hardware Installation

  • 1-1 Safety Precautions

  • 1-2 Hardware Information

    • System Overview

    • Front View

    • Top View

    • Rear View-A

    • Rear View-B

  • 1-3 Getting Ready

    • Connecting Peripherals

    • Connecting the Power Cord

    • Turning on the Computer

• Chapter 2 BIOS Configuration

  • Entering the BIOS Setup Utility

• Chapter 3 Appendix

  • 3-1 How to Perform Q-Flash Plus

  • 3-2 Operating System Installation

• Product Warranty

• GIGABYTE Global Service Network

Parts Checklist

AI TOP 100 Z890 Premium Gaming & AI Empowered Desktop PC (Note):

• Quick Start Guide
• Antenna
• Accessory Cables
• Chassis Accessory Box

*The included accessories are for reference only. Actual accessories may vary. GIGABYTE reserves the right to modify the contents without prior notice.

(Note) AI TOP 100 Z890 Premium Gaming & AI Empowered Desktop PC Model Numbers:

• AT119N9-0000
• AT119N9-0003
• AT119N9-0006
• AT119N9-0001
• AT119N9-0004
• AT119N9-0007
• AT119N9-0002
• AT119N9-0005
• AT119N9-0008

Chapter 1 Hardware Installation

1-1 Safety Precautions

• Before connecting the power outlet, ensure the power cord's rated voltage is compatible with your country/region's power specifications.
• The power cord plug must be connected to a properly wired and grounded power outlet.
• Plug the power cord into an easily accessible power outlet, preferably close to the system. To disconnect system power, ensure you remove the power cord from the power outlet.
• Do not touch the plug with wet hands, as this may cause electric shock.
• Protect the power cord from being stepped on or crushed, especially the plug.
• Do not place the product on vibrating surfaces to avoid damaging internal components.
• Operating temperature range: 5~35°C.
• Do not place the product near any heat sources, such as electric heaters, stoves, or other heat-emitting equipment (including amplifiers).
• The slots or openings on this product are for ventilation to ensure stable operation and prevent overheating. Do not cover or block any ventilation openings with any object.
• Never insert any object through the chassis slots into this product, as they may contact dangerous voltage points or short circuits, potentially causing fire or electric shock. Do not spill any liquid onto or into the product.
• Do not use the product near water, beverages, or liquids. Do not expose the device to rain, liquids, or moisture. This could result in electric shock or property damage. The product is not waterproof or oil-proof.
• Clean the device with a soft, dry cloth.
• The manufacturer specifies that the wing screws should be tightened with a screwdriver. Using wing screws does not violate basic safety rules.
• For information on replacing the motherboard battery, please refer to the motherboard user manual.

1-2 Hardware Information

System Overview

Front View

Diagram showing the front of the computer case with labels for various ports and buttons.

Top View

Diagram showing the top of the computer case with labels for various ports.

• System Reset Button: This button allows users to quickly restart the system.
• Microphone Jack: This jack is for microphone input.
• Audio Output Jack: This jack is for audio output.
• Power Button: This button is used to turn the computer on or off.
• USB 3.2 Gen 1 Ports: These ports support USB 3.2 Gen 1 specifications and are backward compatible with USB 2.0. You can connect USB devices to these ports.
• USB Type-C® Ports (Support USB 3.2 Gen 2x2): These ports support USB 3.2 Gen 2x2 specifications and feature a reversible design. They are also backward compatible with USB 3.2 Gen 2, USB 3.2 Gen 1, and USB 2.0 specifications. You can connect USB devices to these ports.

Rear View-A

Diagram showing the rear of the computer case with labels for various ports.

• DisplayPort Input Port: This port provides graphics card signals to the motherboard. Refer to the description of the ⓐThunderbolt™ 5 Port (USB4® USB Type-C® Port) and the connection diagrams below.

Step 1: Connect your chosen DisplayPort cable (or Mini-DisplayPort cable) from the external graphics card to the DisplayPort input port on the rear of the motherboard.

Step 2: Then, connect your USB Type-C® or DisplayPort device with its cable to the Thunderbolt™ 5 Port (USB4® USB Type-C® Port).

Rear View-B

Diagram showing the rear of the computer case with labels for various ports.

• HDMI Port: This port supports HDMI 2.1b.
• DisplayPort Port: This port supports DisplayPort 2.1b.

1-3 Getting Ready

• This product is designed for vertical use only.
• Peripherals are not included in the accessories.
• It is recommended to connect your monitor to the display output port on the graphics card.

Warning: Before connecting devices and power cords, open the chassis side panel and remove the internal foam bag.

Connecting Peripherals

Connect your peripherals, such as keyboard, mouse, monitor, etc., to the desktop computer.

Diagram illustrating the connection of various peripherals to the rear ports of the computer.

Connecting the Power Cord

Connect the power cord from the accessories to the rear of the desktop computer and to the power outlet.

Diagram showing the power cord connection.

Turning on the Computer

Press the power button to turn on the computer.

Diagram showing the power button location.

Chapter 2 BIOS Configuration

Entering the BIOS Setup Utility

To enter the BIOS setup utility, after powering on the computer, during the POST process, press the <Delete> key to enter the main BIOS setup screen. The CMOS data is powered by the lithium battery on the motherboard. Therefore, this data is not lost when the system power is turned off. When the power is turned on again, the system can read this setup data.

Boot Screen

After powering on, you will see the boot logo screen as follows:

Diagram of the GIGABYTE boot logo screen.

Function Key Descriptions:

• <DEL>: BIOS SETUP\Q-FLASH
  Press the <Delete> key to enter the BIOS setup utility main screen, or to enter Q-Flash via the BIOS setup utility.
• <F12>: BOOT MENU
  The Boot Menu function allows you to set the preferred boot device without entering the BIOS setup utility. Use the <Up> or <Down> arrow keys to select the desired boot device, then press the <Enter> key to confirm. The system will boot directly from the selected device. Note: Settings made in this screen are only for the current boot. After restarting, the system will revert to the boot order set in the BIOS setup utility.
• <END>: Q-FLASH
  Press the <End> key to directly enter Q-Flash without entering the BIOS setup utility.

Warning:

• Updating the BIOS carries potential risks. If you are not experiencing any problems with the current version of the BIOS, it is recommended that you do not update it arbitrarily. If you need to update the BIOS, please proceed with caution to avoid system damage due to improper operation.
• It is not recommended to change BIOS setup utility settings arbitrarily, as this may cause system instability or other unpredictable results. If system instability or failure to boot occurs due to incorrect settings, try clearing the CMOS settings to restore the BIOS to factory default settings (refer to the description of "Load Optimized Defaults" for clearing CMOS settings).

Chapter 3 Appendix

3-1 How to Perform Q-Flash Plus

A. Before starting Q-Flash Plus, please follow the steps below in order:

1. Please visit the GIGABYTE website to download the latest BIOS version compressed file for your product model.
2. Unzip the downloaded BIOS compressed file and save the BIOS file to a USB flash drive, renaming it to "GIGABYTE.bin". (Note: The USB flash drive used must be formatted with the FAT32 file system.)
3. Connect the 12V power connector and the main power connector (if there are two 12V power connectors, choose one) to perform Q-Flash Plus.
4. Turn on the power supply unit, then connect the USB flash drive to the Q-Flash Plus port on the rear of the motherboard.

B. Performing Q-Flash Plus

After pressing the Q-Flash Plus button, the system will automatically search for and compare the BIOS file connected to the Q-Flash Plus port. The QFLED will start flashing (indicating that the comparison and update process has begun). After approximately 6-8 minutes, when the light stops flashing, the BIOS update is complete.

Diagram showing the Q-Flash Plus port and QFLED indicator on the motherboard.

• Before executing Q-Flash Plus, ensure the system is in shutdown state (S5 standby mode).
• If the motherboard is equipped with a BIOS switch and SB switch, please reset them to their default values before executing Q-Flash Plus (BIOS_SW: Boot from Main BIOS, SB: Dual BIOS).
• After the main BIOS update is complete, when the system restarts, it will perform a backup BIOS update using DualBIOS™, and then restart again to boot normally from the main BIOS.

3-2 Operating System Installation

Operating system installation varies depending on the specifications at the time of purchase, divided into verification code and OA3.0.

• Verification Code:
  Follow the reminder label on the chassis, remove all protective materials, correctly connect the power and other interface devices, and press the system power button. The Windows Out-Of-Box Experience (OOBE) screen will appear. When the screen appears, please enter your Microsoft account login (if you do not have a Microsoft account, you can choose to "Create a new account"). Next, simply follow the on-screen prompts to complete the basic OOBE setup. Once this process is complete, it will automatically enter the Windows 11 desktop.
• For regions in the United States and Canada, please note: On the upper left side of the back of the chassis, there is a system verification code (as shown in the figure below). You must provide this verification code for repair purposes. Please keep it safe and consider backing it up by taking a photo, for future reference.

Diagram indicating the location of the verification code.

• Before installation, please ensure the system is connected to the internet.

• OA3.0:
  First Boot
  When you start the computer, the Windows® operating system will display a series of screens. Please follow the on-screen prompts to complete the basic personalization settings. The items to be set are as follows:
  
  • Personalize
  • Get online
  • Settings
  • Your account
  After completing these basic settings, Windows® will begin installing applications and preferred settings. During the setup process, please ensure that the computer is supplied with sufficient and stable power. After successfully logging into your user account, the desktop screen will appear.
  The operating system screen may vary depending on your actual usage.

Driver Installation

A. Motherboard Driver Installation:

After the operating system installation is complete, a dialog box will appear in the lower right corner of the desktop asking if you want to download and install motherboard drivers and GIGABYTE utility software through GIGABYTE Control Center (GCC). Click "Install" to proceed with the installation. (Please ensure that the setting in "BIOS Configuration" > "Settings\IO Ports\Gigabyte Utilities Downloader Configuration\Gigabyte Utilities Downloader" is set to "Enabled").

A screenshot of the GIGABYTE Control Center installation prompt.

When the "EULA (End User License Agreement)" message appears, click "Accept" to install GIGABYTE Control Center (GCC). In the GIGABYTE CONTROL CENTER dialog box, select the drivers and utility software you wish to install, then click "Install" to begin the installation.

A screenshot of the GIGABYTE Control Center interface showing available updates.

B. Graphics Card Driver Installation:

Next, please visit the GIGABYTE website to download the graphics card drivers and utility software.

System Restore (Repair Your Operating System)

If the operating system becomes unstable, there is a hidden partition on the storage device that contains a complete backup image of the operating system. This can be used to restore the operating system to its factory default settings.

Warning:

• If the storage device has been replaced or the hidden partition has been deleted, the restore function will not be available and the system must be sent to a service center for restoration.
• The factory default restore function is only available when the operating system is pre-installed. It is not available for EFISHELL systems.

Starting System Restore

The system restore function is pre-installed on the desktop computer at the factory. This option can launch the Windows recovery tool to reinstall the operating system to its factory default settings. The following is a brief guide on how to launch the restore tool and start the system restore.

System Restore Instructions:

Step 1: Shut down and restart the computer.

Step 2: After powering on the computer, press and hold the F9 key for a few seconds to launch the restore tool.

Step 3: Select "Troubleshoot" to enter system restore and advanced options. (You can also select "Continue" to directly enter the Windows operating system, and back up your personal data and files before restoring.)

There are two system restore methods available:

• Reset this PC: If the computer becomes unstable due to software or setting issues, you can choose to remove or keep your personal files, and then reset the computer settings without losing personal files.
• Smart Recovery: The computer's settings will be restored to factory defaults. (Note! All personal data and files will be lost.)

Step 4: Enter the system reset mode. The toolbar will display restore options. If you are sure you want to restore the system, click "Yes" to proceed.

Warning:

• After selecting restore, all original personal data and files will be deleted, and the system and storage device will be restored to factory default settings.
• Do not turn off the power while the restore window is open and the system restore is in progress.

After the system restore is complete, the toolbar will display an option. Click "Shutdown" to turn off the computer.

Diagram showing the system restore options.

Step 5:

Advanced options

Other advanced options for system restore:

• System Restore: Select a system restore point based on the date and time to restore the system to that point.
• System Image Recovery: Restore the Windows system using a previously created system backup image.
• Startup Repair: Repair and resolve Windows system problems.
• Command Prompt: Use the command prompt to perform advanced troubleshooting.
• UEFI Firmware Settings: Restart to change UEFI BIOS settings.
• Startup Settings: Change Windows startup settings.

Product Warranty

Consumers (referred to as "Purchaser" or "You") who purchase GIGABYTE/AORUS desktop computers or tower PCs (referred to as "Products") are entitled to warranty service from the date of purchase. This warranty applies to new products sold by authorized distributors, retailers, and resellers (referred to as "Suppliers"). It may not apply to "used," "open-box," or "refurbished" products, unless explicitly stated by GIGABYTE/AORUS. This warranty does not apply to extended warranties/upgrade services provided by Suppliers or other third parties. If such services are involved, please contact the third-party service provider directly. Repairing the product at a GIGABYTE/AORUS unauthorized or non-cooperative repair shop, or using third-party replacement parts, does not void this warranty unless such repair or replacement parts cause damage to the product.

The Purchaser must provide a valid receipt or invoice with a clear and legible purchase date and reseller name. If valid proof of purchase for a new product cannot be provided, GIGABYTE/AORUS reserves the right to refuse warranty service or adjust the warranty service period.

To ensure full warranty coverage, Purchasers must complete the product registration for global warranty service. If the Purchaser does not complete the product registration process, they may not be eligible for certain warranty services. Please register your product at the following link: https://profile.gigabyte.com/Login.aspx?S=GIGABYTE

Personal information collected during product registration will be used by GIGABYTE/AORUS and authorized service centers in accordance with the privacy policy (https://profile.gigabyte.com/PrivacyPolicy.aspx?l=en-US) solely for the purpose of providing product services.

Warranty Service

• If the Purchaser encounters product quality issues within the warranty period, GIGABYTE/AORUS will provide service in accordance with applicable warranty terms. Replacement parts provided under warranty will have the same specifications and quality as the original parts and will be serviced according to the warranty terms of the original product. All replaced parts will remain the property of GIGABYTE/AORUS.
• To ensure the efficiency of warranty service, when the Purchaser applies for global warranty service in different regions, GIGABYTE will use parts provided by local authorized service centers for repairs. If you request specific parts, you will have to wait for those parts to be shipped.
• After the product's useful life exceeds the warranty period provided by GIGABYTE/AORUS, repair/replacement parts and service items will be charged according to the relevant fees.
• GIGABYTE/AORUS global service centers will complete repair services as soon as possible after receiving your product. However, if local repair parts are unavailable, the repair time may be affected. If you request specific parts, you will have to wait for those parts to be shipped.
• GIGABYTE provides an online inquiry system for service status. To check the progress of repair services, please have your RMA number ready and provide other required information as requested by the inquiry system. You can easily check the repair status at the following link: https://www.gigabyte.com/Support/Consumer/Repair/Track
• For more service/support information, please click: https://www.gigabyte.com/Support/Consumer

Warranty Exclusions and Disclaimers

• Product warranty does not cover included accessories such as software installation CDs, user manuals, related packaging consumables, nor does it cover promotional gifts provided by GIGABYTE/AORUS, such as peripherals, carrying cases, or backpacks.
• If the product is damaged or malfunctions within the warranty period due to reasons not caused by GIGABYTE/AORUS, such as the following situations, the product will not be covered by the warranty, and the Purchaser will be responsible for the repair costs. GIGABYTE/AORUS reserves the right to determine the cause of the product failure.
• Natural disasters, accidents, or damage caused by user misuse.
• Use of parts not included in the GIGABYTE/AORUS desktop computer's Qualified Vendor List (QVL).
• Product abnormalities caused by testing or evaluation for non-standard purposes.
• Failure of the Purchaser to use the product in accordance with the user manual.
• Extended warranty or upgrade services provided by Suppliers or other third-party resellers are the responsibility of the third party, and GIGABYTE/AORUS assumes no liability.
• If the product's serial number label is lost or unidentifiable, and the product/warranty status cannot be confirmed, the global warranty will be void.
• Personal data stored on the product may be lost during the repair or system recovery process. Purchasers must back up their personal data before sending the product for repair. GIGABYTE/AORUS is not responsible for the loss or recovery of personal data during or after the repair process.
• Purchasers are responsible for shipping and related taxes for global warranty services.
• It is recommended that Purchasers use packaging materials with high protection or the original packaging to ensure the safety of the product during transit.

GIGABYTE Global Service Network

• GIGABYTE Technology Co., Ltd.
  Address: No. 6, Baoqiang Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
  Tel: +886 (2) 8912-4000 Fax: +886 (2) 8912-4005
  Technical Support Hotline: 0800-079-800, 02-8913-1377
  Service Hours:
  Monday - Friday: 09:30 AM - 08:30 PM
  Saturday: 09:30 AM - 05:30 PM
  Technical/Non-technical Support: https://esupport.gigabyte.com
  Website (English): https://www.gigabyte.com
  Website (Chinese): https://www.gigabyte.com/tw
• GIGABYTE eSupport
  For technical or non-technical (business and market) related inquiries, please visit https://esupport.gigabyte.com for assistance.

GIGABYTE

Welcome to eSupport System

Provides online consultation for member products/sponsorships/marketing collaborations, etc. Our customer service representatives will assist you with all your technology-related needs.

Account

Password

Member Login

Quick Links

Or choose

File Download

FAQ

Warranty Service Information

Join Now

Forgot Password

Login