Installation Guide for 2017-19 Ford Super Duty LED Tail Lights

Part I: Remove Tail Lights

Installation Tools

Prepare these tools for installation:

• 1/4 Ratchet
• 1/4 Extension
• 8mm Socket

Textual description of image: A visual display of the required tools: a 1/4 ratchet, a 1/4 extension, and an 8mm socket. An 8mm socket is shown separately with its size indicated.

Whenever working on your vehicle, always make sure your vehicle is OFF and parked. ?

Step 1: Remove Tail Lights Bolts

Open the trunk gate and begin by removing the bolts securing the tail light.

Textual description of image: The rear of a Ford Super Duty truck with the tailgate open, revealing the area behind the driver's side tail light assembly. The truck bed interior is visible.

Take out the top and bottom 8mm bolts from each side of the tail lights.

Textual description of image: Two close-up images show the process of removing the 8mm bolts securing the tail light. A hand holding a ratchet with an 8mm socket is shown accessing the bolts from the inside of the truck body, near the tail light mounting points.

Carefully pull the tail light outward to remove it.

Textual description of image: A hand wearing a black glove is shown carefully pulling the original tail light assembly outward from the truck body to detach it.

Step 2: Unplug Sockets and Remove Tail Lights

Prior to removing the tail lights, unplug the sockets.

Textual description of image: Two close-up images display the electrical connectors and bulb sockets at the rear of the removed tail light assembly. Hands wearing black gloves are shown disconnecting the vehicle's wiring harness from the tail light.

Step 3: Remove Lightbulbs from the Sockets

Extract the lightbulbs from each socket and remove them before proceeding with the installation.

Textual description of image: Hands wearing black gloves are shown carefully extracting the original lightbulbs from their sockets on the removed tail light assembly.

Repeat the steps for the other side to fully remove the tail lights.

Textual description of image: The empty mounting location on the truck body after the original tail light has been removed. The wiring harness with disconnected electrical connectors is visible.

Part II: Install AlphaRex Tail Lights

Textual description of image: A pair of new AlphaRex PRO-Series LED Tail Lights is presented, showcasing their sleek, modern design with intricate LED patterns.

Step 1: Plug the Sockets and Install Tail Lights

Connect the wire connectors directly into the sockets on the new ALPHAREX tail lights.

DO NOT USE DIELECTRIC GREASE!

Textual description of image: A hand wearing a black glove is shown connecting the vehicle's wiring harness connector to the corresponding socket on the new AlphaRex LED tail light assembly.

Twist and secure the socket into the new tail lights. DO NOT USE DIELECTRIC GREASE! Follow the reverse of the removal process to install the new tail lights into the vehicle.

Textual description of image: Two close-up images illustrate the installation of the new tail lights. The first shows a hand securing the electrical socket into the new tail light. The second shows a hand guiding the new AlphaRex tail light assembly into its mounting position on the truck.

Step 2: Complete Installation

Utilize a ratchet to tighten the 2 X 8mm bolts on each side. Note: When using a power wrench, be cautious not to overtighten the bolts.

Textual description of image: A hand using a ratchet with an 8mm socket is shown tightening the two bolts that secure the new AlphaRex tail light assembly to the truck body. A note advises caution when using a power wrench to avoid overtightening.

Congratulations! You have completed the installation for ALPHAREX 17-19 Ford Super Duty LED TAIL LIGHTS.

Textual description of image: The rear view of a Ford Super Duty truck with both new AlphaRex LED tail lights fully installed and illuminated, showcasing their distinctive lighting patterns and modern appearance.

Textual description of image: Two close-up views of the newly installed AlphaRex LED tail lights on the truck, highlighting the detailed LED patterns and overall aesthetic enhancement.

Disclaimer

This installation article is a tutorial guide. By reading this article, you agree it is for reference only and AlphaRex USA and its distributors make no guarantee on the finished results. Under no circumstances whatsoever shall AlphaRex USA nor its distributors be liable for any damage, misuse or personal injuries. If you do not fully understand the installation procedure, it is highly recommended that you seek help from professional mechanics to do the installation.