User Manual for DEKALA models including: SWS-S002 Weather Clock 3-Day Weather Forecast Smart Weather Station, SWS-S002, Weather Clock 3-Day Weather Forecast Smart Weather Station, 3-Day Weather Forecast Smart Weather Station, Forecast Smart Weather Station, Smart Weather Station, Weather Station, Station
SWS-S002 User Manual (PDF) Dekala DEKALA Dekala,Weather,Clock,3-Day,Weather,Forecast,Weather,Station,Wireless,Indoor,Outdoor,Thermometer,Hygrometer,Home,Temperature,Monitor,Remote,WiFi,Temperature,Sensor,Humidity,Gauge,Atomic,Alarm,Clock,B0C23YQBCJ,B0B885BRRQ,B0B468QPL4
Dekala Weather Clock 3-Day Weather Forecast Weather Station Wireless Indoor Outdoor Thermometer Hygrometer Home Temperature Monitor Remote WiFi Temperature Sensor Humidity Gauge Atomic Alarm Clock : Patio, Lawn & Garden
Dekala WeatherStation ProTM (SWS-S002) Indoor weather station Wireless sensor User Manual Please read this manual carefully before using the product and keep it in proper storage. (V1.2) Download App Instruction Videos Support@dekalastore.com Please feel free to contact us if you need any assistance. 01 Content Warning 03 Feature Description 03 Packing List 04 Base Unit Specification 05 Sensor Specification 05 Quick Guidance 06 Installation and placement 09 1. Installation and placement 09 2. Sensor placement 10 3. Sensor battery charging 10 4. How to Pair Base Unit and Sensor 11 APP Connection 14 1. Download the App 14 2. Wi-Fi connecting mode 14 App Guidance 15 1. Connect device to app 15 2. WeatherStation Pro Home Page 17 3. Alarm Clock 18 4. Share Device 20 FAQS 21 02 Warning Please keep the sensor in a safe place to prevent children from swallowing it. When using this product, ensure that the environmental temperature is within the range of -4(-20°C) to 140(60°C), and the humidity is between 0% and 99%. This product is not fireproof, so please do not expose it to fire or any other heat source. This product is not waterproof, so do not immerse it in water as it may damage the equipment. Feature Description This is a smart weather clock that downloads online weather data for the local area where the product is located and displays weather information, including time, date, temperature, and humidity. The Base Unit provides access to multiple sensors (up to three sensors). You can place the sensors indoors or outdoors, and the collected data will be transmitted and displayed on the Base Unit. You can configure and control the product through an app, and you can check weather data on both the indoor Base Unit and the app. However, you can only access indoor/outdoor historical temperature records on the app. 03 Packing List Base Unit *1 Charging Cable *1 Sensor *1 lanyard *1 Adapter *1 Dekala WeatherStation ProTM (SWS-S002) Indoor weather station Wireless sensor User Manual Please read this manual carefully before using the product and keep it in proper storage. (V1.2) User Manual *1 04 Base Unit Specification Model Size Color Weight Operating Temperature Communication Accuracy SWS-S002 Material 160×23×160mm Output Black Input 335g Temperature unit -4-140(-20~60) Humidity unit WiFi (2.4G) + Bluetooth Temp: ±0.5 Humidity : ±2 %RH ABS+PC USB-A 5V-1A Micro USB 5V-2A / RH% Sensor Specification Power supply Power input Standby power consumption Standby duration Communication frequency Communication distance 3.7V 400mA lithium battery Micro USB 11uA Up to 6 months 433.92MHz Up to 80M in outdoor open environment Certification 05 Quick Guidance Front View Weather icon Weather Forecast: sunny, cloudy, overcast, rain, thunder, snow UV Index Online city temp & humidity data Digital clock WiFi Alarm clock Month/date Day of the week 06 Sunrise and sunset time Sunrise icon Sunset icon Temperature & humidity data from base unit Weather forecast for the next three days Lowest temperature Highest temperature Weather Forecast Day of the week Back View Hanging Hole Sensor sync /reset button WiFi setup button Power input Top View Power output Power input Stand Display Brightness Control Turn off alarm clock 07 About the Sensor Front View LED light (hidden) Top view Pair Button Lanyard slot Back View 08 Interior View Micro USB Installation and placement 1. Installation and placement Two way of Base Unit installation. Power input Stand on table Mount on wall Back view Wall hanging hole Power input Side view 09 2. Sensor placement Please insert the lanyard through the hole. 3. Sensor battery charging To Unlock, press down with the palm of Insert micro USB your hand and rotate counterclockwise. power input charging cable To lock, press down with the palm of your hand and rotate clockwise. Note: The red indicator signifies that the device is "Charging". Once fully charged, the red indicator will disappear. 10 4. How to Pair Base Unit and Sensor "The Base Unit should be placed indoors, while the Sensors can be placed both indoors and outdoors within the maximum communication distance." Note: The distance between the Base Unit and the Sensors should be 50-80m/164-262ft (without obstacles). (2) "After plugging in the power, connect to the 2.4G WiFi (refer to page 12)." Default Time-Display Default display WiFi icon flashes Default Time-Display Network connected; Online weather data available; The local temperature & humidity of the Base Unit updates normally. 11 (3) To enter synchronous mode, long-press the "SYNC/PAIR" button, and the sensor channel icon will flash. First, press the button on the sensor to activate it, and the light spot on the front side will start flashing. Then, press and hold the button on the sensor to synchronize it with the base unit. The base unit will beep once after successful synchronization and automatically exit SYNC mode. Connection Succeed WiFi icon stays solid Long Press SYNC/PAIR button Long Press 12 Sync succeed (4) To add an additional sensor, short press the "SYNC/PAIR" button again to activate sync mode. Press the button on the sensor to activate it, causing the light on the front side to flash. Then press and hold the button on the sensor to sync the second sensor, and you will hear one beep to indicate success. Repeat these steps to sync a third sensor. After syncing, press the button on the paired sensor. The base unit will beep three times to confirm the connection. If not, it means the sync failed or the sensors are out of range. To reset, long press the "SYNC/PAIR" button to clear all sensor channels and data, and you will hear three beeps from the buzzer. 13 APP Connection 1. Download the App Download "Dekala" from App Store/Google Play or scan QR code, sign up and log in. Attention: Wi-Fi (2.4 GHz only). Please allow the app to access your cellphone's Bluetooth before connecting. The app will help you automatically find your device. Also, please enable the app to access your cellphone's location so that the app and device can obtain weather data for your city from the service provider. 2. Wi-Fi connecting mode Plug in to power, the flashing connection; indicates the device is now under Wi-Fi connecting modeready for If stays solid, Long-press "WiFi" button till flashes to enter Wi-Fi connecting mode. WiFi icon flashes Long press WIFI button 14 APP Guidance 1. Connect device to app Open up "Dekala" app, click " " or "Add Device"; Turn on Bluetooth as prompted, click on "Add"; Select the device you want to connect and click" "on the right; 15 Please type in the 2.4 GHz Wi-Fi password and click on "Next" (make sure that both your smartphone and the Dekala app are connected to the 2.4 GHz Wi-Fi network); When connecting, please put the device, your smartphone, and the router in the same area, as close to each other as possible; Once the device has successfully connected to your 2.4 GHz Wi-Fi network, you can choose to rename it. Click on "Done" to complete the Wi-Fi setup process. Dekala 2.4G 16 2. WeatherStation Pro Home Page Time and date Sunset time Weather forecast for the next three days (weather status; highest/lowest temperature; day of the week) Base Unit data (temperature; humidity; alarm setting) Sensor 1 data (temperature; humidity; alarm setting) Geographical location UV Weather data (weather status; current temperature & humidity) Alarm clock setting Historical data Low battery warning (when Sensor battery is less than 10%) 17 3. Alarm Clock 1To set an alarm clock, you can only use the app; 18 2Turn Off Alarm Clock: Turn off alarm clock by App; Turn off alarm clock by buttons / / . 19 4. Share Device Click the " " icon located in the upper right corner, then find the "Share Device" option to share the data. 20 FAQS 1. The device cannot connect? Please place the router, device, and mobile phone in the same area (as closely as possible). FAEQnsSure that your Wi-Fi signal is strong and usable at least (only 2.4GHz Wi-Fi networks are supported). To connect to a different smartphone or Wi-Fi network, long-press to re-enter Wi-Fi connecting mode. 2. What if weather data is not available or accurate? Reconnect the Base Unit with 2.4GHz Wi-Fi first, and the weather data will automatically be obtained and refreshed after the network is available. The weather data will update every 15 minutes. Allow Dekala(App) to access your location for accurate data. Our customer service team is available 24/7 for troubleshooting. 3. Sensor data does not display on Base Unit/Sensor is disconnected? Keep devices at least 3ft/9m away from electronics like TVs, computers, microwaves, etc., and pay attention to the working distance. Long-press the button on Sensor and check if a red spot is shown (battery run out if no red spot). Press the "SYNC/PAIR" button on Base Unit, and then press the button on Sensor to synchronize the data with Base Unit to display. 4. Failed to synchronize Base Unit with Sensor? Long-press the "SYNC/PAIR" button on Base Unit to clear all connected channels before entering sync mode. You will hear a beep three times to indicate you are in sync mode. Press and hold the button of the remote sensor, and you will hear a beep once to indicate sync success. A Base Unit can be paired with up to 3 Sensors. 21Adobe PDF library 15.00 Adobe Illustrator 24.0 (Windows)