User Manual for speco technologies models including: AIPK1 Single Door 2 Wire Video Intercom Kit, AIPK1, Single Door 2 Wire Video Intercom Kit, 2 Wire Video Intercom Kit, Video Intercom Kit, Intercom Kit
Speco AIPK1 Single Door 2-Wire Video Intercom Kit | 123 Security Products
Note: With an extended TF card, up to 40 videos can be stored and up to 1000 images can be stored. Monitoring. Monitoring. Unlock the door when monitoring.
Indoor Monitor Station User Manual v1.0 Menu AIIS07 Overview This product is an indoor monitor station. Functions such as calling, intercom, monitoring and unlocking are available, details are as below: Supports video intercom, unlocking Supports real-time monitoring from outdoor station Supports multiple indoor monitors in one house Supports intercom in one apartment and intercom between different apartments Supports TF card extension, photo capturing and video recording Supports secondary doorbell Supports KNX home automation extension 1. Video Monitoring Click to enter monitor interface. Image effect, photo capturing and video recording can be set. 2. Intercom Click to enter intercom interface. User can call and talk in one apartment or different apartments. Call in 3. Message Click to enter message interface, user can check captured photos, recorded videos and device information. 4. Setting Click to enter setting interface, user can configure ringtone/language/ time and operate configuration setting. Dimensions & Interface Unit: mm Calling In Steps: Doorbell rings Talk Unlock the door End of incoming call: 1. Visitor calls the indoor monitor from outdoor station, the indoor monitor starts ringing; 2. Resident presses button then talk with visitor. 3. During the conversation, resident presses button to unlock the door for visitor. 4. 5 seconds after unlocking the door, the call ends automatically and system returns to standby mode. 5. Resident presses button to end the call. BUS1-A BUS1-B: Bus Interface 1; BUS2-A BUS2-B: Bus Interface 2; EXT-DC24V GND: Extended Power Supply 24V. GND Doorbell: Interface for secondary doorbell button. 1.Master-slave indoor monitor setting (M stands for Master, S stands for Slave). 2.Video terminal resistance matching. Interface for secondary doorbell. Interface for 485 extension. Setting Setting: 1. When visitor is calling, click to adjust brightness, color, and contrast manually. Photo Capture 1. During the call from visitor, click to capture manually. 2. Captured photos will be saved in message. Note: Maximum of 50 images can be stored if there is no external TF card. Video Recording: 1. During the call from visitor, click to record a video manually (must insert a TF card); 2. Video will be saved in the message. Note: With an extended TF card, up to 40 videos can be stored and up to 1000 images can be stored. Monitoring Note Video terminal matching needs to be set on the last indoor monitor by setting the switch No.2 to ON; Bus Interface 1 and Bus Interface 2 are for connecting indoor monitors in series. Monitor of indoor monitor will turn on and ring, while slave indoor monitor will not turn on but only ring. Key Button Function Parameter Working Voltage: DC 2430V Working Current30V 200 mA Resolution800×480 Dimensions (L /W /D) 220×140×24 mm Static Current30V 15 mA Display7inch TFT LCD TF card capacity232GClass 4 is suggested Basic Functions and Setting Monitoring Unlock the door when monitoring Steps: Choose the device to monitor Monitoring Unlock End 1. Click the icon in the GUI, choose the device to monitor. The default monitoring device is the outdoor station 1, if the outdoor station 1 does not exist, there will be no monitoring. 2. Resident can choose different outdoor station by and . If the chosen monitor does not exist, it will exit monitoring and return to standby mode. 3. During monitoring, resident can press to unlock for visitor, monitoring will end in 5 seconds after the door is unlocked. 4. Click to end monitoring. Talk with visitor Steps: Monitor Talk End 1. During monitoring, resident can press to talk with visitor. Active Call Click and enter intercom interface. 1 2 Password Setting Factory Reset Calling Interface Intercom between different apartments Steps: Call Ring Talk End 1. Call Input the room number and click to call; 2. Indoor monitor echoes back. 3. The resident will click to answers the call and click to reject the call. 4. Resident can click call after communication. to end the Intercom in one apartment Steps: Call Talk End 1. Click to call the indoor monitor in one same apartment. 2. Indoor monitor echoes back. 3. The called indoor monitor in the same apartment echoes back. 4. Resident can press to answer the call, click to reject the call, after answering the call, user can click to end the call. Check Messages Check Photos Password Setting 1. Click to enter password setting. 2. Input new password and input again to confirm. Factory Reset 1. Click reset interface. to enter factory Unit 4 Installation Height Message Checking Photo Checking 1. Click to check messages, captured photos, recorded videos and device information. 1. Click to check photos. 2. While checking photos, click to choose the next one, click to choose the last one, click to delete the current one, click photo record. to empty the Video checking Device Information Suggested height for installation: 1.5m Unit 5 Installation Instruction Video Checking 1. Click videos. to check recorded 2. While checking videos, click to choose the next one, click to choose the last one, click to delete the current one, click to empty the video record. Device Information Checking 1. Click to check device information including software version and device address. Unit 3 System Setting Language Setting Configuration Setting Step 1Align the screw hold of bracket with the holes of 86 box. Tighten the screw and fix the bracket. Step 2Connect the indoor monitor with wire, and the opening with the hook of the bracket. Then, move down the device a little bit. It's set correctly when you hear the joint click. Language Setting Interface 1. Click setting interface. , enter language 2. Language must be set in initial start-up. Inputting Password 1. Click input password to enter configuration setting. Note: Password is 123456. ADD Setting Bracket installed Attention 1. Please keep devices away from strong magnetic fields, high temperature and wet environments. 2. Please handle with care, a drop or any hard impact will damage the device. 1. Click setting. Configuration Setting to enter address Add Setting Note 1.Add setting from 001 to 200. 2.If there are multiple indoor monitors in one apartment, the address of all indoor monitors should be the same. 3 3. Please do not use a wet cloth or chemicals to wipes devices. 4. Please do not disassemble the device. 4Microsoft Word for Microsoft 365