Pro'sKit Official Website
User Manual for Pro sKit models including: MT-7029N Noise Filtering Network PoE Toner and Probe, MT-7029N, Noise Filtering Network PoE Toner and Probe, Filtering Network PoE Toner and Probe, Network PoE Toner and Probe, Toner and Probe
MT-7029N Noise-filtering Network PoE Toner & Probe Kit | Pro'sKit Official Website
File Info : application/pdf, 2 Pages, 1.39MB
DocumentDocumentMT-7029N Noise-Filtering Network PoE Toner & Probe
Thank you for purchasing and using the Pro'sKit MT-7029N NoiseFiltering Network PoE Toner & Probe. Please read the instruction manual carefully before using this product, and keep it properly for future review.
OVERVIEW MT-7029N is the new upgrade version with a better noise filtering design. The high-frequency filter circuit technology eliminates the noise and anti-interference line tracer. Suitable for ordinary network, PoE network, UTP / STP cable search, and positioning. The new function can locate the port with flashing signals; check the crimping quality of the plug single-way; be able to trace the wire & cable mapping at the same time. Ideal for all installation & maintenance jobs.
INTRODUCTION
Figure1. MT-7029N Transmitter Diagram
Crimping: RJ45 plug crimpingqualitytest socket. POL/Scan:Scan & telephone line test socket. Test/Scan:RJ45cablemaptest & scansocket. 1~8/G:Cable map & Shielded indicator. 1~8:RJ45 plug crimping quality testindicator. Power/BAT LOW:Power ON/OFF & Battery low indicator. Function indicator:
Test:Cable map & Shielded function indicator. Scan:Locating and isolating cables function indicator. Flash: Network port flashing function indicator.
)XQFWLRQLQGLFDWRU Crimping: RJ45 plug crimping test function indicator. POL: Telephone line + / -pole test function indicator. POL/GPOL/R:Phone line polarity indicator.
:Power ON/OFF button. Test/Scan:Cable map test &Scanfunction button.
1. Flash: Network port flashing function button. 1. Crimping:RJ45 Plug crimpingqualitytest button. 1. TEL/POL:Phone line polarity function button. 1. Battery cover.
Figure 2. MT-7029N Receiver Diagram
1. Probe: Wire tracing and NCV detection. 2. LED light. 3. Power ON/OFF indicator. 4. NCV indicator. 5. Signal status indicator. 6. Volume control. 7. Earphone socket (PP). 8. Function switch (LED light/NCV/OFF/SCAN mode). 9. Speaker. 10. Locating and tracing cables function button 11. 1~8/G Cable map & Shielded indicator 12. RJ45 (8 pin) / RJ11 (6/4/2 pin) cable mapping test socket. 13. Battery cover
SPECIFICATIONS
MT-7029N Transmitter specifications RJ45 Lan cable Cat5, 5e, 6, 7 (UTP/STP), RJ11/12 telephone cable
Wire tracing
Voltage8Vp-p Frequency455KHz
Tracing distance 600m
Cable mapping
RJ45 Test/Scan socket for RJ45eRJ11/RJ12 locating Individual wire pairs
8+1 LED indicators.
Test distance max.: 300m
Crimping Test
For RJ45, RJ11/RJ12 plug 8 LED indicators
Port Flash
Telephone line POL +/-
1 LED indicator 1 dual color LED: POL-Green/ POL+Red
Auto power off Low battery indication
1 hour About 7.0V; power indicator will flash.
Voltage protection
DC 60V
Battery
9V (NEDA 1604/6F22) x1pcs
W orking current
Tracing/Cable map/Crimping <35mA; Port flash <110mA
Dimension
L138 x W80 x D35mm
W eight
142g
MT-7029N Receiver Specifications
Frequency
Tracing indication Cable mapping Cable map indication
455KHz 1 LED indicator & speaker RJ45 socket 8+1 LED indicators
NCV Earphone
1 LED indicator & speaker (AC 90-1000V) 3.5mm socket
Lighting
1 LED
Low battery
indication
About 7.0V; power indicator will flash.
Battery
9V (NEDA 1604/6F22) x1pcs
W orking current
Tracing <200mA; lighting<50mA
Dimension
L203 x W50 x D32mm
weight
95g
Accessories
RJ45 cable patch cords x2, RJ11 cable patch cords x2, RJ11 to alligator clips patch cord x1,
earphone x1, storage bag, user manual.
OPERATION MT-7029N Transmitter
Do not connect with DC 60V live circuit equipment or it might
cause damage. ý Cable Mapping
This function is to check the network cable connection is good or not.
To connect the cable with the transmitter and receiver, by viewing the
transmitter and receiver 1-8 / G indicators to verify the network cable
connection situation. It can test the network cable straight, short,
open, and crossover. You can also connect the transmitter directly to
the network switch or the network interface test the cable connection.
The operation is as follows: 1. Insert the cable into the transmitter theTest/Scansocket and the
other end into the receiver socket. 2. Press the button, the power indicator is on. 3. Press theTest / Scanbutton , theTestindicator will light, and
the cable mapping will be started automatically.
4. There are four results as following examples: z Straight:
T: 1-2--4--6-7-8 T: 1-2--4--6-7-8-G R:1-2--4--6-7-8 R:1-2--4--6-7-8-G z Crossover:
T: 1---4--6-7-8 T: 1-2--4--6-7-8
R:1-2--4--6-7-8 z Open:
R:1---4--6-7-8
T: 1-X--4--6-7-8
R:1-X--4--6-7-8 z Short:
T: 1-2----6-7-8
T: 1-2--4--6-7-8
R:1-2----6-7-8 R:1-2----6-7-8
The FDEOHPDSindicators 3&/('aOLJKWXSDQGWKHRWKHUV DUHRII 3&/('a OLJKWXSDQGWKHRWKHUV DUHRII 3&/('aOLJKWXSDQGWKHRWKHUs DUHRII
ý Wire Tracing This function is using the transmitter to send the signals and the receiver to receive the signals with an audio alarm. It has strong noise-filtering design, and you can identify the correct wire easily. Specific operations are as follows: 1. Insert the tracing wire into the transmitterTest / ScanorPOL /
Scansocket. 2. Turn the transmitter, pressTest / Scanbutton twice, the Scan
indicator will light, and the transmitter will send the signals. 3. The transmitter will send the signals and check the cable status at
the same time. You will know each line status through the indicator led (1-8). 4. Turn on the receiver and you will hear a beep sound means the machine is on. The power indicator will light. 5. Rotate the adjustable sensor knob clockwise to turn the sensitivity to the maximum. Press & hold theSCANbutton. The receiver will be receiving the signals from the transmitter, once it receives the signals, it will send audio alarm, so you can find the correct wire.
6. When tracing the wire, you need to press & hold the receiver SCANbutton. The receiver will stop receiving signals once you release the button. Kindly remind you to remove the battery after using it to save energy.
7. You might receive signals from more than one wire. In this case, please try to rotate the adjustable sensor knob counter-clockwise to lower the sensitivity, and you will be able to find the correct wire.
ý Plug Crimping Quality Check
This function can single-way check RJ45/RJ11 plug crimping quality at
RQHVLGHDQGQRQHHGWRFRQQHFWWRWKHRWKHUVLGH ,W¶V convenient & smart. 1. Insert the network cable into the transmitterCrimpingsocket. 2. Press the button to turn on the transmitter and press the
Crimpingbutton.
3. The transmitter will start to check the cable pin to pin and the indicator ofCrimping1-8 will light up if all the connection are
JRRG7KHRQHGRHVQ¶WOLJKWXSPHDQVWKHFRQQHFWLRQLVGRZQ For example as follows, the 2 & 5 pin are broken.
1-X--4-X-6-7-8
ý Port Flash
This function will help you to locate the port quickly, the transmitter will
send the flashing signals, so you can easily determine the correct port. 1. Insert the network cable into the transmitterTest/Scansocket and
the other side to network switch. 2. Press the button to turn on the transmitter, press theFlash
button , theFlashindicator will light or flash.
3. Check the indicators on the network switch, If the indicator flash
around every 3 seconds, the corresponding port is the correct port.
ý Telephone Line POL +/-
This function is suitable for testing and determining the polarity of a
telephone line. 1. Insert the alligator clip RJ11 cable into the transmitter POL/Scan
socket. 2. Press the button to turn on the transmitter, press the
TEL/POLbutton , thePOLindicator will light.
3. Clip the red and black alligator each side of the telephone line, and
the
indicator will light.
4. If the indicator light is red, the red alligator is on the positive pole &
the black alligator is on the negative pole. If the indicator light is
green, then the red alligator is on the negative pole & the black
alligator is on the positive pole.
ý Non-contact Voltage Detection (NCV)
This function is used to determine if there is a live circuit, the detection
range is AC90-1000V (50 / 60Hz). z Turn on the receiver and switch to the NCV position, move the
receiver probe close to the test subject. If the AC voltage is detected, the speaker will send an audio alarm in different frequency. The higher frequency the higher voltage is.
Note: z This function is for reference, the voltage may still remain even there
is no detection. There are many possible factors might block the
detection. z There are some factors (like flashlight and motor) might also trigger
non-contact voltage detection.
MT-7029N-CPoE
Pro'sKit MT-7029N-CPoE MT-7029N$ & PoEUTP/STP RJ45(UTP/STPCat 5Cat 6Cat 7)RJ11/12( 2/4/6 pin) /
MT-7029N-C
MT-7029N-C 1.Crimping: 2.POL/Scan:RJ11+/- 3.Test/Scan: RJ45/RJ11 4. 1~8/G : 5. 1~8 : 6.POWER:/ 7. : "TEST"
"SCAN" . "FLASH. 8. : "Crimping". "POL"+/- "POL+/-" 9. :/ 10.TEST/SCAN: 11.Flash: 12.Crimping: 13.TEL/POL:+/- 14.
<110mA
LxWxD 138x80x35mm
142g
.5/$
455KHz 1 LED RJ45
8+1 LED
AC 90-1000V 50/60Hz 1 LED & ¶3.5mm
1 LED
7.0V
9V (NEDA 1604/6F22) x1pcs
<200mA; <50mA
LxWxD203x50x32mm
95g RJ45 x2RJ11 x2RJ11 x1, x1,,
2.
/Power/BAT LOW
POLPOL.
3.
4.
5.
() NCV
,AC90-1000V50/60Hz
z NCV
,
: www.prokits.com.tw
DC 60V
()
1-8/G
RJ45 1. Test/Scan
2. /POWER/BAT LOWTest/Scan
TEST/LED . UTP/STP 1~8/G PIN 1~8/G ,G
T: 1-2-3-4-5-6-7-8 T: 1-2-3-4-5-6-7-8-G R:1-2-3-4-5-6-7-8 R:1-2-3-4-5-6-7-8-G
. UTP/STP1~8/G PIN1~8/G 1~8/G
T: 1--3-4-5-6-7-8 T: 1-2-3-4--6-7-8 R:1-2-3-4--6-7-8 R:1--3-4-5-6-7-8
. UTP/STP1~8/G PIN1~8/G LED
T: 1-X-3-4-5-6-7-8 R:1-X-3-4-5-6-7-8
. UTP/STP1~8/G PIN1~8/G 1~8/Gi 3
T: 1-2-3--5-6-7-8 T: 1-2-3-4--6-7-8 R:1-2-3---6-7-8 R:1-2-3---6-7-8
. RJ-11/126LED"2-74"3-62 "4-5"RJ45
1. RJ45
2. POWERTest/Scan1-8/G
MT-7029N-C
1. 2. LED 3. 4.(NCV) 5. 6. 7. ø3.5mm 8. 9. 10.SCAN 11.1~8/G 12. RJ45/RJ11 13.
MT-7029N-C
RJ45 5FTU4DBO Cat55e67/
RJ11/12
8Vp-p
455KHz
600m
RJ45 Cat55e67/RJ11/12
8+1 LED
300m
RJ45 (Test/Scan) RJ45RJ11/RJ12
8 LED
1 LED
1 LED(): POL-Green/ POL+Red
1
7.0V
DC 60V
9V (NEDA 1604/6F22) x1pcs
// <35mA;
() 1. Test/ScanPOL/Scan. 2. /Power/BAT LOW
Test/ScanScan 3. ,1-8,
1-8 4. Scan
5. SCAN
6. SCAN
7.
()
Crimping
1.
/Power/BAT LOW
CrimpingCrimping
2. Crimping
3. Crimping"1-8"
()
LED
1. Test/Scan,
.
2.
/Power/BAT LOW
FlashFlash3
3. 3
() 60V 1. RJ11POL/Scan.
MT-7029N-C
12 ()
x (
)
·
·
·
x
· ...
·
,
130 7 5 886-2-22183233 E-mail: pk@mail.prokits.com.tw / 1365 25 021-68183050 400 1699 629
PROKIT'S INDUSTRIES CO., LTD
http://www.prokits.com.tw E-mail: pk@mail.prokits.com.tw ©2022 Copyright by Prokit's Industries Co., LTD. All rights reserved 2022001(A)