Qualcomm QTS110 User Manual

General Description

The QTS110 is an ultra-low power, cloud-connected, globally usable track and sense device designed for the shipping and logistics industry. It tracks cargo location and monitors environmental conditions during transit and warehousing, supporting multimodal journeys across land, sea, and air.

The device utilizes a cellular radio with three access technologies: LTE-M, NB-IoT, and GPRS/2G. It features a GNSS receiver and a Wi-Fi receive module for location determination by scanning nearby Wi-Fi access points. Additionally, it is equipped with various sensors to measure environmental conditions. The QTS110 transmits location and sensor data to the cloud periodically or when specific events are triggered.

Design and Components

The QTS110 has the following dimensions: 50mm x 125mm x 14mm and weighs approximately 140g.

Key Components:

• Front Cover: White (W3225) PC (LG-GN8010F) with a textured finish (MT11015). Features a reference color sample for the icon, a Qualcomm logo printed in Pantone 2728 C, and a laser-engraved QR code.
• Back Cover: White (W3225) PC (LG-GN8010F) with a textured finish (MT11015).
• Type-C USB Cover: White (W3225) PC (LG-GN8010F) with a textured finish (MT11015).
• LED Light Pipe: Clear material (PMMA LG-870S) with a textured finish (MT11015).
• Power Key: White (W3225) PC (LG-GN8010F) with a textured finish (MT11015).
• Tem-Hum Sensor Hole: Clear material.
• Pressure Sensor Hole: Clear material.
• Charging Pad: Clear material.
• Light Sensor: Clear material (PMMA LG-870S) with a glossy finish.

Sensors:

• Inertial Measurement Unit (IMU)
• Temperature sensor
• Humidity sensor
• Ambient light sensor
• Pressure sensor

Connectivity and Features:

• One USB2.0 Type-C female connector
• Power button
• 1x Red/Green/Blue LED
• eSIM
• Communications module supporting LTE-M, NB-IoT, and 2G
• Wi-Fi module for positioning

Use Cases and Capabilities

Use Cases Supported by QTS 110:

• Asset tracking and remote management
• Shipment tracking and logging
• Totes and pallet shipment
• Cold chain tracking for food and pharma
• Air cargos

Capabilities QTS 110:

• International Protection rating: IP65
• Multi-mode LTE Cat.M1, LTE Cat.NB2, EGPRS
• Geolocation: GNSS, cellular & Wi-Fi based positioning
• Status LEDs: GNSS status, cellular status, power status
• Programmable non-mechanical touch power button
• Battery powered with high efficiency
• Out-of-the-box cellular connectivity

Device Battery Charging

The QTS110 can be charged by placing it on its charging cradle. During charging, the device displays a blinking color LED, which changes color when the charge reaches 85% or higher. Once charging is complete, the device should be removed from the cradle.

Charging Specifications:

Device Label

The QTS110 has been certified by regulatory bodies and includes markings related to these certifications. The markings on the device label include:

• Model number: QTS110
• FCCID: 2AQ68-QTS110
• ICCID: 24374-QTS110
• SN (Serial number)
• IMEI
• CE logo
• WEEE logo
• UL logo
• England UKCA logo
• Warning logo of UL

QR Code

The QR code on the device can be scanned with a smartphone camera to access a device-specific public URL. This URL provides information about the tracker, such as its firmware, shipment status, and battery life. The URL is public and does not contain journey-specific details like origin, destination, or current location, nor customer-specific information.

Specifications

Flight Mode

The QTS110 features a flight mode that disables the device's transmitters when the device is in flight, adhering to FAA advisory circular A.C 91.21-1D. The flight detection algorithm is designed to prevent emissions during flight. It uses two independent sources to confirm flight status: the cellular radio's speed/velocity assessment and an accelerometer sensor detecting specific event sequences. The device is only allowed to transmit if both checks confirm it is not in flight. If either check fails, the device enters airplane mode, preventing cellular transmission and reception.

Sensor Details:

• Acceleration Sensor: LSM6DSO32TR, a 3-axis combo sensor with accelerometer and gyroscope in a small land grid array package (LGA). Operating temperature range: -40 °C to +85 °C.
• Cellular Radio: Qualcomm low-power modem MDM 9205, supporting LTE-M (eMTC), NB-IoT, and 2G/EGPRS. LTE-M and NB support power class 5 (up to 20 dBm transmit power). 2G supports up to 33 dBm transmit power.

LED States

LED Requirements for Connectivity, Location and Sensor:

LED states related to battery and charging:

Safety and Regulatory Guidelines

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation.

The QTS110 has been tested and meets the limits for a Class B digital device according to Part 15 of the FCC rules, designed to provide reasonable protection against harmful interference in residential installations. The device generates, uses, and radiates radio frequency energy, and improper installation or use may cause interference to radio communications. No guarantee is made against interference in a particular installation.

To correct interference with radio or television reception:

• Increase the distance between the QTS110 and the receiver.
• Connect the equipment to an outlet on a circuit different from the receiver's.
• Consult the dealer or an experienced radio/TV technician.

If the QTS110 is experiencing interference:

• Ensure the device is plugged into an outlet no closer than 10 ft (3 m) to a Wi-Fi access point, microwave oven, or 2.4 GHz cordless phone.
• Move the device to a different electrical wall outlet to increase distance from other electronic equipment.

Do not:

• Install the device in locations with ignitable or flammable gases or liquids.
• Expose the device to extreme temperatures.
• Plug the AC Adapter into a power source not matching the marked input voltage ratings.
• Operate the device with a damaged plug or after it malfunctions, is dropped, or damaged. Avoid dropping the device.
• Clean the tracker with solvents or immerse/dip it in water.
• Dispose of the tracker in household waste. Use compliant USB cables and do not crack open the tracker casing.

Federal Communications Commission (FCC) Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The QTS110 has been tested to the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The QTS110 generates, uses, and radiates radio frequency energy, and if not installed and used according to instructions, may cause harmful interference to radio communications or be interfered with. There is no guarantee that interference will not occur in a particular installation.

Battery Warnings

English Version:

CAUTION

• Risk of explosion if the battery is replaced by an incorrect type.
• Disposal of a battery in fire or a hot oven, or mechanical crushing or cutting of a battery can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may result in an explosion or leakage of flammable liquid or gas.
• When using a Class I AC adapter, it must be earthed. The power plug must be connected to a properly wired earth ground socket outlet. Hazardous voltage could occur on user-accessible metal parts due to improper wiring of the socket outlet.
• This product is intended to be supplied by a UL Listed Power Adapter rated output 5Vdc, min. 1.5A. The maximum ambient temperature (Tma) is 60 degrees C minimum, and the altitude is 2000m minimum.

French Version:

MISE EN GARDE:

• Attention: Risque d'explosion si la pile n'est pas remplacée correctement. Remplacez uniquement par un type identique ou équivalent. Jetez les piles conformément aux instructions du fabricant.
• Mise au rebut d'une BATTERIE dans un feu ou un four chaud, ou écrasement ou découpage mécanique d'une BATTERIE, pouvant entraîner une EXPLOSION.
• Laisser une BATTERIE dans un environnement extrêmement chaud pouvant entraîner une EXPLOSION ou une fuite de liquide ou de gaz inflammable.
• Une BATTERIE soumise à une pression d'air extrêmement basse pouvant entraîner une EXPLOSION ou une fuite de liquide ou de gaz inflammable.
• Lors de l'utilisation de l'adaptateur secteur de classe I, il doit être mis à la terre. La fiche d'alimentation doit être connectée à une prise de terre correctement câblée. Une tension dangereuse peut se produire sur les pièces métalliques accessibles à l'utilisateur en cas de câblage incorrect de la prise de courant.
• Ce produit est destiné à être alimenté par un adaptateur d'alimentation homologué UL avec une sortie nominale de 5Vdc, min. 1,5 A. La température ambiante maximale (Tma) est de 60 degrés C minimum, et l'altitude est de 2000 m minimum.

ISED Compliance Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) L'appareil ne doit pas produire de brouillage; (2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Radiation Exposure Statement

This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 30 cm between the radiator and your body.

Cet équipement est conforme aux limites d'exposition aux radiations FCC/IC CNR-102 établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 30 cm entre le radiateur et votre corps.