Quest HI-E DRY 140 Dehumidifier: Quick Start Instructions

Introduction

This manual provides essential information to acquaint you with the Quest HI-E DRY 140 dehumidifier, ensuring successful installation, operation, and maintenance. Ultimate satisfaction depends on proper installation and a thorough understanding of the equipment. The dehumidifier is built using tested engineering principles and has passed rigorous quality inspections.

Safety Instructions

• The device is designed for indoor use in spaces protected from rain and flooding.
• Ensure adequate space for maintenance and service access to back or side panels; do not install with service panels inaccessible.
• Avoid directing discharge air at people or over water in pool areas.
• If used near water (pool, spa), ensure the unit cannot fall in, be splashed, and is plugged into a Ground Fault Interrupt (GFI) protected circuit.
• Do not use the device as a bench or table.
• Do not place the device directly on structural members; use vibration isolation to minimize noise and vibration.
• A drain pan is required under the unit if installed above a living area or where leakage could cause damage.
• Never operate a unit with a damaged power cord. It must be replaced by the manufacturer, its service agent, or a similarly qualified person.
• Electrical connections must comply with the current edition of the NEC ANSI/NFPA 70 and applicable national/local codes.
• Maintain a 3 ft (1m) clearance around the air intake and exhaust to prevent obstruction.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience/knowledge, unless supervised or instructed by a responsible person. Supervise children to ensure they do not play with the appliance.
• This appliance is not intended for use in elevations over 2000 m (6,562 ft).

[Warning] Do not use means to accelerate defrosting or cleaning other than those recommended by the manufacturer.

[Warning] Store the appliance in a room without continuously operating ignition sources (e.g., open flames, operating gas or electric heaters).

[Warning] Do not pierce or burn. Refrigerants may not contain an odor.

Assembly & Installation

Thank you for purchasing the Quest Hi-E Dry 140 dehumidifier. Follow these steps for successful assembly and installation. For a complete manual, visit QuestClimate.com/manuals.

1. Unpack Box

2. Register Warranty

   Register at thermastor.com/registration [QR Code]

3. Check Parts

   • A. Dehumidifier (1)
   • B. Drain Hose (1)

4. Read Remaining Steps and Warnings

5. Decide Where to Place Unit in Room

   [Warning] Do not block airflow inlet. Outlet must be at least 12 inches from walls and other obstructions.

   [Warning] Risk of fire due to flammable A2L refrigerant used. See manual for handling instructions and follow national regulations.

6. Push Lever to Extend Handle

   The push lever, located beneath the handle, extends it to 50" for easy transport, including on stairs.

7. Transport Ready

   With the handle extended, the Quest Hi-E Dry 140 is ready for transport. It is designed as a dolly for air movers; stack F9 or F10 fans for convenient mobility.

8. Verify Wall Outlet

   Ensure the wall outlet has the correct voltage and amperage.

9. Plug in Dehumidifier

   The unit will enter "STAND BY" mode.

10. Attach Drain Hose

    Attach one end of the condensate hose to the drain adapter plug (under the storage pocket lid) and the other end to a drain, bucket, or sink.

Specifications @ 80°F / 60%RH

11. Press the Power Button

    Upon powering on, a light bar above the display illuminates for 1 second, then turns off. The compressor activates 60 seconds after selecting the Power button.

    The dashboard displays:

    • Top Section: Inlet Conditions (Temperature, Humidity, Grains per Pound)
    • Middle Section: Exiting Conditions (Temperature, Humidity, Grains per Pound)
    • Bottom Left: Current humidity set point (default: 50%)
    • Bottom Right: Run time since last power-up (top); lifetime usage in hours (bottom)

12. Change Humidity Setpoint

    Press the NEXT arrow button 10 times, or until the Humidity Setpoint screen appears. Press the UP arrow to increase the setpoint; press both arrow buttons simultaneously to decrease it.

    From any screen, touch the droplet button [?] to return to the dashboard.

    Note: Dark Mode is default. The screen darkens after 10 minutes. Press any button to re-illuminate.

13. Fold Handle for Storage

    Push down on the handle to unlock, and fold it back down for compact use and storage.

After Dehumidification

Follow these steps when finished with your dehumidifier:

1. Press the "POWER" Button

   Press the "POWER" button. Wait for the "POWERING DOWN" timer to complete. This allows the blower to remove water from the coils and warm them up to prevent condensation.

   Important: A final purge occurs at the end of the power-down cycle.

   (Display shows: POWERING DOWN, System shutdown in 0:47, with POWER, PURGE, NEXT, SET buttons)

2. Unit Enters "STAND BY" Mode

   Once in "STAND BY" mode, unplug the dehumidifier and disconnect the condensate hose.

3. Storage

   Store the condensate hose back in the storage pocket at the top of the dehumidifier.

4. Accessories

   To purchase additional accessories, scan the QR code [QR Code] or visit QuestClimate.com/Product-Category/Accessories/All-Accessories/.

   A. Replacement Filter: Change filters every 3-6 months, or with each grow cycle for optimal performance in growing applications.

Visit QuestClimate.com

Limited Warranty

WARRANTOR: Therma-Stor LLC, 4201 Lien Rd, Madison, WI 53704. Telephone: 1-877-420-1330.

WHO IS COVERED: This warranty extends only to the original end-user of the Quest Hi-E Dry 140 dehumidifier and may not be assigned or transferred.

FIRST YEAR WARRANTY: Therma-Stor LLC warrants that for one (1) year, the Quest Hi-E Dry 140 dehumidifier will operate free from defects in materials and workmanship. Therma-Stor LLC will, at its option, repair or replace defective part(s) free of charge.

SECOND THROUGH FIFTH YEAR WARRANTY: Therma-Stor LLC warrants that for five (5) years, the condenser, evaporator, and compressor will operate free from defects in material or workmanship. Therma-Stor LLC will, at its option, repair or replace defective part(s), provided all labor and transportation charges are borne by the end-user.

END-USER RESPONSIBILITIES: Warranty service must be performed by an authorized Therma-Stor LLC Servicer. If an authorized Servicer cannot be located, contact Therma-Stor LLC Service Department for assistance. Service will be performed during normal working hours. Proof of purchase (lease) must be presented upon request. The end-user is responsible for normal care. This warranty does not cover defects resulting from misuse, abuse, lack of normal care, corrosion, freezing, tampering, modification, unauthorized/improper repair or installation, accident, acts of nature, or causes beyond Therma-Stor LLC's control.

LIMITATIONS AND EXCLUSIONS: Replacement parts are warranted only for the remainder of the original warranty period. All implied warranties, including merchantability and fitness for a particular purpose, expire upon the expiration of the written warranty. Therma-Stor LLC is not liable for oral warranties. Therma-Stor LLC is not liable for special, indirect, or consequential damages, including water damage, lost profits, or loss of use, regardless of legal theory. Some states may not allow limitations on implied warranty duration or consequential damages.

LEGAL RIGHTS: This warranty grants specific legal rights, which may vary by state.

Serial Number: [Placeholder for Serial Number]

Part Number: [Placeholder for Part Number]

Register your new dehumidifier at thermastor.com/registration or scan the QR code [QR Code].