Introduction
This document provides instructions for the OMRON HEM-7159T-AP3 Automatic Blood Pressure Monitor. This device is intended for home use to measure systolic blood pressure, diastolic blood pressure, and pulse rate using the oscillometric method. Please read this manual thoroughly before using the monitor.
Important Safety Information:
- This device is not intended to be used as a diagnostic tool.
- Consult your physician for any health concerns.
- Ensure the correct cuff size is used for accurate readings.
- Keep out of reach of children.
What's Included
Your OMRON HEM-7159T-AP3 package typically contains:
- Main unit
- Arm Cuff (HEM-FL31)
- 4 "AA" Batteries
- Storage Case
- Instruction Manual 1 and 2
- Setup Instructions
Diagram Description: A visual representation of the package contents, showing the blood pressure monitor unit, a folded arm cuff, batteries, and a storage case.
Understanding Your Monitor
Main Unit Components:
- Display: Shows blood pressure readings, pulse rate, and error messages.
- Start/Stop Button: Initiates or stops a measurement.
- Memory Button: Accesses stored measurement data.
- Battery Compartment: Located on the back of the unit.
Arm Cuff (HEM-FL31):
- Designed for upper arm circumference.
- Features an air plug and cuff tube.
Diagram Description: An illustration of the main blood pressure monitor unit with callouts pointing to the LCD display, the Start/Stop button, the Memory button, and the Power/Battery indicator. Another illustration shows the arm cuff with labels for the cuff tube connector and the cuff itself.
Getting Started
1. Battery Installation
Open the battery cover on the back of the main unit. Insert 4 "AA" batteries, observing the correct polarity (+/-). Close the battery cover.
Icon Description: A battery symbol [?] indicating power source.
2. Applying the Arm Cuff
Sit comfortably with your back supported and feet flat on the floor. Remove tight clothing from your upper left arm. Place the cuff on your bare upper arm, about 1-2 cm (about 1 inch) above the elbow. The tube should run down the inside of your arm. Fasten the cuff snugly but not too tight. Ensure the cuff is positioned correctly as per the diagram.
Diagram Description: A diagram illustrating the correct placement of the arm cuff on the upper arm. It shows the cuff wrapped around the arm, with the air tube positioned correctly and the cuff edge 1-2 cm above the elbow joint. An arrow indicates the direction to wrap the cuff.
3. Taking a Measurement
- Press the Start/Stop button. The cuff will automatically inflate.
- Remain still and do not talk during measurement.
- The cuff will deflate, and your systolic blood pressure, diastolic blood pressure, and pulse rate will be displayed.
- Press the Start/Stop button again to turn off the monitor.
Tips for Accurate Measurement:
- Sit quietly for at least 5 minutes before taking a measurement.
- Avoid eating, drinking alcohol, smoking, bathing, or exercising for 30 minutes before measurement.
- Ensure the cuff is applied correctly and is the right size.
Memory Function
The monitor can store up to 60 measurements. Press the Memory button to view past readings. The display will show the average of all readings, followed by individual readings in chronological order.
Icon Description: A memory chip symbol [?] indicating data storage.
Maintenance and Care
- Clean the main unit and cuff with a soft, damp cloth. Do not use abrasive cleaners.
- Store the monitor and cuff in the provided storage case in a cool, dry place.
- Replace batteries when the low battery indicator appears [⚠️].
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No reading or incorrect reading | Cuff applied incorrectly | Reapply cuff, ensuring correct placement and tightness. |
| Cuff is too loose or too tight | Adjust cuff for a snug fit. | |
| User moved during measurement | Remain still during measurement. | |
| Low battery indicator [⚠️] appears | Batteries are low | Replace all batteries with new ones. |
| Error code E1, E2, E3, E4, E5, E6 | Various measurement errors | Refer to the full instruction manual for specific error code meanings and solutions. Generally, reapply cuff and try again. |
Diagram Description: A table summarizing common issues, their potential causes, and recommended solutions for operating the blood pressure monitor.
Specifications
| Feature | Specification |
|---|---|
| Model | HEM-7159T-AP3 |
| Display | Digital LCD |
| Measurement Method | Oscillometric Method |
| Power Source | 4 x 1.5V AA Batteries |
| Battery Life | Approx. 300 uses (new alkaline batteries) |
| Pressure Range | 0 to 299 mmHg |
| Pulse Rate Range | 40 to 180 beats/min |
| Accuracy | Blood Pressure: ±3 mmHg, Pulse: ±5% of reading |
| Cuff | HEM-FL31 (Medium/Large) |
| Operating Environment | 10°C to 40°C (50°F to 104°F), 30% to 85% RH |
| Storage Environment | -20°C to 60°C (-4°F to 140°F), 10% to 95% RH |
Contact Information
For support or inquiries regarding your OMRON HEM-7159T-AP3, please visit the OMRON Healthcare website or contact your local OMRON representative.
External Link Placeholder: [OMRON Healthcare Website](https://www.omronhealthcare.com)
