Camden CX-91S TDS Series Magnetic Locks

1. SPECIFICATIONS

Figure 1: Basic Installation Concept & Accessories

2. INSTALLATION

1. Drill the armature plate holes in the door using the sticker template provided.
2. Attach the armature plate to the door with the hardware provided as per Figure 2.3.
3. With the door closed, mark the door frame at the edge of the armature to properly align the electromagnet to the armature.
4. Attach the mounting plate to the door frame using the self-tapping screws provided. Align the mounting plate with the mark from Step 3.
5. Insert the wires through the hole in the mounting plate and into the electromagnet unit. Attach the electromagnet unit to the mounting plate with the Allen head fixing screw.
6. Screw in the anti-tamper nuts to prevent unauthorized access and make sure to fully tighten the fixing screw with proper tool. A “T” Handle Allen Key.
7. The electromagnetic lock must be installed in accordance with the following:
   
   • Life Safety Code ANSI / NFPA 101.
   • Local Authority having Jurisdiction.
   • Manufacturer's installation instructions provided with each unit.
   The power supply units must be mounted inside the secured or protected area.
8. Typical wiring method shall be in accordance with CSA C22.1, Canadian Electrical Code, Part I, Safety Standard for Electrical Installations, Section 32.

Note: Install in indoor dry location. Use caution when changing factory default setting. It is recommended to apply a light coat of silicon lubricant to the mating surface on a monthly basis to prevent rust. Manufacturer's Instructions provided in each unit.

NOTICE: All models are recognized to: UL 294 and ULC S533-15 : Standard for Access & Egress. Models CX-91S-06 & CX-91S-12 are listed to: UL 1034, Standard for Burglary-Resistant Electric Locking Mechanism. UL 294, Access Control System Units ** Value not verified by UL.

Remark: All drawings shown are for illustration purpose only. Actual product may vary due to product enhancement.

3. TROUBLE SHOOTING

1. Sensor not functioning:
   
   • Improper attachment of electromagnet and armature plate.
   • Modification of the PCB
2. Door not locked:
   
   • Incorrect wiring or no power from power supply
3. Reduced holding force:
   
   • Poor contact of electromagnet and armature. Be sure armature is loose enough that it can fully contact electromagnet along the entire length.
   • Mating surface is dusty or damaged.
   • Improper input voltage or wire size.

Door Contact Sensor; Max. Contact Rate: 40VDC, 0.25A

LED Status:

• Red = Locked
• Green = Released
• Off = No Input (Only for LED-TB Models)

IMPORTANT! Set the jumper position according to the power input correctly before switch ON the power.

Diagram showing wiring connections for power supply, push switch, dry contact, and timer settings (5s, 10s, 15s, 25s). Includes labels for PS, C, NO, NC, and jumper settings for 12 VDC and 24 VDC.

4. REGULAR INSTALLATION GUIDE (FIGURE 2)

Step 1: Fold the CX-91S Template along the dotted line up to 90°. Note: Installation Template Only for In-door E.M. Lock Model 300, 600, 1200.

Step 2: Close the door, position the EM lock mounting location as close to the door upper corner with a gap of 10mm.

Step 3: Place the template against the door & frame and drill holes according to template indications.

Step 4: Drill 2 holes on the frame and 3 holes on the door as indicated on the template.

Step 5: Install the Armature Plate to the door. Note: Actual installation may vary according to door figures.

Step 6: This allows the armature plate to pivot around the armature screw to compensate for door misalignment.

Step 7: Mount the FB600 on the door frame by screwing in the self-tapping screws on the holes as indicated on the template.

Step 8: Once the position is correct, screw in the other screws to permanently mount the plate, and drill the wire cable access hole.

Step 9: Use an Allen key wrench to unscrew the anti-tamper nut and tighten the fixing screws on the mounting plate.

Step 10: Connect to power supply and test unit.

5. LZ BRACKET FOR IN-SWING DOOR INSTALLATION GUIDE (FIGURE 3)

Step 1: Position the L-Bracket mounting location as close to the door upper corner with a gap of min. 10mm; ensure the door can close. The door frame minimum height value "L" is needed to accommodate the bracket Model: 800 LZ (H: 2-1/16" / 52mm), 1200 LZ (H: 2-7/8" / 73mm).

Step 2: Place the bracket and secure with fixing screws.

Step 3: Tighten the EM Lock on the L-Bracket by using the Allen Wrench.

Step 4: Assemble the Z-bracket and ensure the Z-bracket can be adjusted freely, before permanent tightening.

Step 5: Install the armature plate on the Z-Bracket, using the CSK screw provided in the screw pack.

Step 6: Close the door, and position the Z-Bracket by bringing the armature plate close to the EM Lock surface.

Step 7: Turn on the power of the EM Lock, let the armature plate attach to the EM Lock; adjust the position between the Z-Bracket and the door.

Step 8: Once the position is correct, screw in the self-tapping screws on the Z-Bracket to the door.

Wire Gauge Chart: A table shows recommended wire gauge (AWG) for different distances (25f to 1000f) and current draws (0.25A to 2.00A) for both 12VDC and 24VDC.

5. INSTALLATION

1. Drill the armature plate holes in the door using the sticker template provided.
2. Attach the armature plate to the door with the hardware provided as per Figure 2.3.
3. With the door closed, mark the door frame at the edge of the armature to properly align the electromagnet to the armature.
4. Attach the mounting plate to the door frame using the self-tapping screws provided. Align the mounting plate with the mark from Step 3.
5. Insert the wires through the hole in the mounting plate and into the electromagnet unit. Attach the electromagnet unit to the mounting plate with the Allen head fixing screw.
6. Screw in the anti-tamper nuts to prevent unauthorized access and make sure to fully tighten the fixing screw with proper tool. A “T” Handle Allen Key.
7. The electromagnetic lock must be installed in accordance with the following:
   
   • Life Safety Code ANSI / NFPA 101.
   • Local Authority having Jurisdiction.
   • Manufacturer's installation instructions provided with each unit.
   The power supply units must be mounted inside the secured or protected area.
8. Typical wiring method shall be in accordance with CSA C22.1, Canadian Electrical Code, Part I, Safety Standard for Electrical Installations, Section 32.

Note: Install in indoor dry location. Use caution when changing factory default setting. It is recommended to apply a light coat of silicon lubricant to the mating surface on a monthly basis to prevent rust. Manufacturer's Instructions provided in each unit.

NOTICE: All models are recognized to: UL 294 and ULC S533-15 : Standard for Access & Egress. Models CX-91S-06 & CX-91S-12 are listed to: UL 1034, Standard for Burglary-Resistant Electric Locking Mechanism. UL 294, Access Control System Units ** Value not verified by UL.

Remark: All drawings shown are for illustration purpose only. Actual product may vary due to product enhancement.

4. TROUBLE SHOOTING

1. Sensor not functioning:
   
   • Improper attachment of electromagnet and armature plate.
   • Modification of the PCB
2. Door not locked:
   
   • Incorrect wiring or no power from power supply
3. Reduced holding force:
   
   • Poor contact of electromagnet and armature. Be sure armature is loose enough that it can fully contact electromagnet along the entire length.
   • Mating surface is dusty or damaged.
   • Improper input voltage or wire size.

Door Contact Sensor; Max. Contact Rate: 40VDC, 0.25A

LED Status:

• Red = Locked
• Green = Released
• Off = No Input (Only for LED-TB Models)

IMPORTANT! Set the jumper position according to the power input correctly before switch ON the power.

Diagram showing wiring connections for power supply, push switch, dry contact, and timer settings (5s, 10s, 15s, 25s). Includes labels for PS, C, NO, NC, and jumper settings for 12 VDC and 24 VDC.

5. REGULAR INSTALLATION GUIDE (FIGURE 2)

Step 1: Fold the CX-91S Template along the dotted line up to 90°. Note: Installation Template Only for In-door E.M. Lock Model 300, 600, 1200.

Step 2: Close the door, position the EM lock mounting location as close to the door upper corner with a gap of 10mm.

Step 3: Place the template against the door & frame and drill holes according to template indications.

Step 4: Drill 2 holes on the frame and 3 holes on the door as indicated on the template.

Step 5: Install the Armature Plate to the door. Note: Actual installation may vary according to door figures.

Step 6: This allows the armature plate to pivot around the armature screw to compensate for door misalignment.

Step 7: Mount the FB600 on the door frame by screwing in the self-tapping screws on the holes as indicated on the template.

Step 8: Once the position is correct, screw in the other screws to permanently mount the plate, and drill the wire cable access hole.

Step 9: Use an Allen key wrench to unscrew the anti-tamper nut and tighten the fixing screws on the mounting plate.

Step 10: Connect to power supply and test unit.

6. LZ BRACKET FOR IN-SWING DOOR INSTALLATION GUIDE (FIGURE 3)

Step 1: Position the L-Bracket mounting location as close to the door upper corner with a gap of min. 10mm; ensure the door can close. The door frame minimum height value "L" is needed to accommodate the bracket Model: 800 LZ (H: 2-1/16" / 52mm), 1200 LZ (H: 2-7/8" / 73mm).

Step 2: Place the bracket and secure with fixing screws.

Step 3: Tighten the EM Lock on the L-Bracket by using the Allen Wrench.

Step 4: Assemble the Z-bracket and ensure the Z-bracket can be adjusted freely, before permanent tightening.

Step 5: Install the armature plate on the Z-Bracket, using the CSK screw provided in the screw pack.

Step 6: Close the door, and position the Z-Bracket by bringing the armature plate close to the EM Lock surface.

Step 7: Turn on the power of the EM Lock, let the armature plate attach to the EM Lock; adjust the position between the Z-Bracket and the door.

Step 8: Once the position is correct, screw in the self-tapping screws on the Z-Bracket to the door.

Wire Gauge Chart: A table shows recommended wire gauge (AWG) for different distances (25f to 1000f) and current draws (0.25A to 2.00A) for both 12VDC and 24VDC.