Instructions for HySecurity models including: SlideDriver II, SlideDriver II Slide Gate Operator, Slide Gate Operator, Gate Operator
HySecurity SlideDriver II SD50F (Replaces 222 X3 ST) **Now Available** – Protec Controls
HySecurity SlideDriver II SD15 (Replaces 222 SS ST) **Now Available** – Protec Controls
File Info : application/pdf, 4 Pages, 574.01KB
DocumentDocumentThe following instructions are intended to assist the user in the installation of the heater unit for use on the SlideDriver II gate operators. The heater prevents components from freezing and not operating properly. Please read all assembly instructions before installing the kit. PARTS Heater strip Heater cord Romex connector Cover plate Thermal switch Heater contactor HARDWARE 1/4-20 x 1 in bolt 1/4 in washers 7/16 in nuts 8-32 x 1/2 in self-tapping screw TOOLS Standard wrenches #29 drill bit (0.136 in) PREPARATION 1. Remove cover. 2. Set the power switch to OFF. 3. Carefully unclamp the drive wheels. 4. Remove the SmartTouch 720/725 Controller. 5. Drill a #29 (0.136 in) hole in the back of the electrical enclosure (Figure 3). 6. Install the thermal switch in the hole and fasten with two 8-32 x 1/2 in self-tapping screws (Figure 4). SLIDEDRIVER II HEATER CAUTION Turn off power to the gate operator and take the necessary precautions to avoid electrical shock. Power Switch Figure 2. Set Power Switch to OFF 2 1 Figure 3. Remove SmartTouch 720/725 Controller Loosen cover screws Lift cover Thermal Switch Area Figure 1. Remove the Cover Figure 4. Install Thermal Switch D1157 Rev. B ©2023 1 SLIDEDRIVER II HEATER INSTALL THE HEATER 7. Remove the two 1/4 in bolts attached to the pin tabs. 8. Remove the pins. Lift the pivot arms to make the pins easier to remove (Figure 5). Figure 5. Remove Pivot Arm Pins 9. Slide the two pivot arms and motors out as a complete unit (Figure 6). Figure 7. Install Heater Strip HEATER WIRING (FIGURE 10 AND FIGURE 11) 11. Connect the heater cord to the heater strip; be sure to bend the terminals up so that they contact no metal surfaces. 12. Use the romex connector and lock washer and route the heater cord through the bottom hole in the pivot post (Figure 8). 13. Take the romex connector and tighten it down onto the heater cord. 14. Install the cover plate with two 8-32 screws (Figure 9). Figure 6. Remove Pivot Arm Assembly 10. Install the heater strip vertically in the drive post with the terminals down and facing out with the 1/4-20 x 1 in bolts (Figure 7). Note: Use a flat washer on the outside of the drive post and a flat washer on the inside of the drive post as a stand off keeping the heater strip from contacting the paint of the drive post. Complete the mounting by adding the 7/16 in nuts. 2 support.hysecurity.com Figure 8. Strain Relief Figure 9. Strain Relief and Cover SLIDEDRIVER II HEATER 15. Take the heater cord up to the electrical box and run it through one of the knockouts. Use the plastic cord connectors to attach to the panel wall. 16. Install the heater contactor in the electrical box and connect the heater contactor to the power supply or motor contactor: L1 to L1 and L2 to L2. 17. Connect one lead of the heater cord to terminal T1 of the heater contactor and connect the other to T2. 18. Install thermal switch to power supply -V and heater contactor A2. 19. Connect power supply V+ to heater contactor A1. FINISH INSTALLATION 20. Clean any debris from drilling the thermal switch hole. 21. Install the SmartTouch 720/725 controller on the mounting brackets and reconnect any disconnected wires. 22. Reinstall the pivot arms and pins. 23. Carefully clamp the drive wheels. 24. Set the power switch to ON and test cycle the gate. 25. Close the electrical box and install the cover. B THERMAL SWITCH NO TO MOTOR B HEATER KITS: MODELS COVERED: Drawing REV B Figure 10. Heater Strip Wiring, non-VFD D1157 Rev. B ©2023 3 SLIDEDRIVER II HEATER B THERMAL SWITCH NO TO VFD B HEATER KITS: MODELS COVERED: Drawing REV B Figure 11. Heater Strip Wiring, VFD 4 support.hysecurity.com TO VFD