User Manual

Important Safety Instructions

WARNING: Keep small parts away from children.

Strangulation Hazard: Children can become entangled in cords. Power cords should be kept more than 3 feet away from the crib and baby's reach at all times. Baby monitors and cameras with power cords should never be hung on or near the crib.

This product is not a toy and should be kept out of children's reach.

Read and keep all safety and operating instructions.

This product cannot replace responsible adult supervision.

Water and Moisture: This product is designed for indoor use only. Do not expose to rain, moisture, dripping, or splashing. Do not place liquid-filled objects on or beside the product.

DO NOT: Use the appliance if the cord or plug is damaged. Contact a service center for inspection and repair to avoid potential risks.

DO NOT: Attempt to repair or adjust electrical or mechanical functions, as this will void the guarantee.

Ventilation: Do not use on a bed, sofa, rug, or similar surface that may block ventilation openings. Do not place in an enclosed area like a bookcase or drawer that may impede airflow.

Keep away from heat sources: Do not expose to direct heat sources such as candles, radiators, heat registers, stoves, or other appliances that emit heat. Do not leave in direct sunlight.

Power source: Use only the AC power adapters included in this package.

Damage requiring service: This unit should be serviced by qualified personnel.

Package Contents

• Parent unit x 1
• Baby unit x 1
• Parent unit adapter x 1
• Baby unit adapter x 1
• User manual x 1

FCC & IC Statements

This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

If this equipment causes harmful interference to radio or television reception, try correcting the interference by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consulting the dealer or an experienced radio/TV technician.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Max. Report SAR (1g): Body: 0.297W/kg

Warranty Terms

All products come with a one-year warranty from the original purchase date against defects in workmanship and materials. For warranty or support issues, please contact the store where you purchased the product or the Amazon seller.

Installation Guidelines

To use the parent unit and baby unit together, a radio link must be established between them; range is affected by environmental conditions.

Large metal objects (refrigerators, mirrors, filing cabinets, metallic doors) or reinforced concrete between the units may block the radio signal.

Signal strength may also be reduced by solid structures like walls, or by radio or electrical equipment such as TVs, computers, cordless or mobile phones, fluorescent lights, or dimmer switches.

Use of other 2.4GHz products (wireless networks, Bluetooth, microwave ovens) may cause interference. Keep the baby monitor at least 5ft (1.5m) away from these products or turn them off if they cause interference.

Product Overview

Parent Unit Overview

• 3.5" LCD screen
• Power & Charging LED
• Volume LED
• MIC
• Menu/Exit button
• Volume / Down button
• Talk to baby button
• Brightness + / Right button
• Brightness - / Left button
• Power button
• Volume + / Up button
• Amplification
• OK button
• Reset key (under stand)
• Speaker
• Light sensor
• Infrared LEDs
• CMOS sensor
• Power LED
• Pair key
• USB-Jack
• Temperature sensor
• Stand
• DC-Jack

Diagram Description: The parent unit features a 3.5" LCD screen, various control buttons (Menu/Exit, Volume Up/Down, Brightness Up/Down, Talk, OK, Power), LEDs for power and charging status, a microphone, and a speaker. The baby unit includes a camera lens (CMOS sensor), infrared LEDs for night vision, a microphone, a speaker, a power LED, a pair key, a USB jack, a temperature sensor, and a stand with a DC jack.

Icons Overview

• Signal: ?
• Volume: ?
• Brightness: ?
• ECO: ?
• Alarm: ⏰
• Lullaby: ?
• Camera: ?
• Battery: ?
• Zoom: ?
• Night Vision: ?
• Talk to baby: ?️
• Temperature: ?️

Placement of the Baby Monitor

Select a location for the camera that provides a clear view of the area to monitor, is free from dust, and is not in line-of-sight to a strong light source or direct sunlight.

Avoid installing the camera where there are thick walls or obstructions between the camera and the monitor.

STRANGULATION HAZARD: Keep cords out of child's reach. Never place camera or cords within 3 feet of crib or playpen. NEVER use extension cords with AC adapters; only use the AC adapters provided.

Using the Baby Monitor

Turn On the Baby Unit

Use the AC adapter included in this package (5V, 600mA). Connect it to the wall outlet. The unit will turn on automatically, and the power LED will light up.

Turn On the Parent Unit

Use the AC adapter included in this package. The parent unit is supplied with a built-in rechargeable Li-ion battery. Connect the monitor to the adapter plugged into the mains whenever possible to keep the battery charged.

Press and hold the power key on the left side of the parent unit. The power LED will light up, and the image will display on the LCD screen.

OSD Mode Operation

• Parent Unit Screen On/Off: Short press the power key.
• Volume Adjustment: Press the UP key ? to increase the volume; press the DOWN key to decrease the volume.
• Brightness Adjustment: Press the Left key ? to decrease the brightness; press the Right key to increase the brightness.
• Digital Zoom & Pan / Tilt: Press and hold the Menu/Exit key for approximately 2 seconds to zoom in/out. At the Zoom mode, press the navigation key to Pan/Tilt the image. A zoom icon will be displayed on the top of the screen. Note: If you want to adjust the volume/brightness, you must exit the Zoom mode first.
• Camera View/Scan: (Only if two or more cameras are paired) Press the OK key ? to view/scan cameras. During scan mode, the scan icon will be displayed on the top of the screen. Each camera's video will stay on the LCD for about 10 seconds before changing to the next camera.
• Talk to Baby: To talk, press and hold the talk key ?️ on the front of the monitor. Release the button when finished talking to listen to sounds from the baby's room again. You cannot listen to your baby while talking to them.
• Infrared Night Vision (Automatic): This function allows the camera to pick up images in dark or low light conditions. In this mode, only black and white images will be displayed on the monitor. The optimum image is achieved with a 6-foot distance between the baby unit and the object.

Menu Operation

• ECO Setting: Controls sound activation. The ECO default setting is OFF. If there is no sound around the camera within 30 seconds, it stops transmitting, and the monitor screen turns off. When the camera detects sound louder than the set sensitivity level, it starts transmitting the signal to the monitor again. To change the ECO level: Press Menu/Exit, use LEFT/RIGHT keys to highlight the ECO icon ?, use UP/DOWN keys to select the desired level, and press OK to confirm.
• Alarm Setting: Use the alarm to remind yourself to feed the baby, change diapers, sleep, etc. Press Menu/Exit, use LEFT/RIGHT keys to highlight the alarm icon ⏰, use UP/DOWN keys to set the time (decrement/increment), and press OK to confirm. Note: If the alarm rings and no one answers, it will last 1 minute, stop, and then start again after 3 minutes. The ringing will sound up to three times total if no one answers.
• Lullaby Setting: Soothe the baby by playing a gentle lullaby from the baby unit. Press Menu/Exit, use LEFT/RIGHT keys to highlight the lullaby icon ?, use UP/DOWN keys to select, and press OK to confirm.
• Pairing the Camera and Monitor: Press Menu/Exit, use LEFT/RIGHT keys to highlight the camera icon ?, use UP/DOWN keys to select the desired camera to pair, and press OK to start pairing. While the LED is flashing, press the PAIR button on the back of the camera. The screen will display the image from the camera once paired. Repeat steps if unsuccessful.
• Temperature Unit Setting: Press Menu/Exit, use LEFT/RIGHT keys to highlight the temperature icon ?️, use UP/DOWN keys to select the unit, and press OK to confirm.

Technical Data

• System General: Frequency: 2.4GHz, Type of Modulation: GFSK, Transmitting Power: 18dBm Max.
• Operation Environment: Indoor use only; Temperature: 0-40°C; Humidity: 5% to 90% RH (relative humidity).
• Operating Range: Up to 900 feet (straight line and open space).
• Power adapter: Input: 100-240VAC 50/60Hz, 200mA Max; Output: 5V, 600mA/700mA.
• LCD: 3.5" TFT LCD.
• Rechargeable battery for monitor: Model: 503450; 3.7V, 950 mAh, 3.515Wh.
• Operating time with battery fully charged (parent unit): Up to 10 hours (ECO on).
• Image sensor type: 1/6.5' Color CMOS image sensor.
• IR LED Type: 940 nm.

Troubleshooting

• Cannot hear the baby on the parent unit: Volume setting may be too low.
• No reception on the monitor: Power adapters may not be properly connected. Confirm that the camera and monitor are ON. Camera may be far away from the monitor. Camera and monitor may not be properly paired (follow PAIRING instructions). Battery power may be too low.
• Interference or poor reception: Move the monitor close to the camera. The camera or monitor may be placed too close to many metal objects. Other electronic devices may be interfering with the signal.
• Feedback (screeching, static): The camera and monitor may be too close together. The volume on the monitor may be set too high.
• Image frozen: Restart the baby unit (unplug the adapter then plug it into the socket again).

General Troubleshooting Step: Press the reset key at the back of the Parent unit (hidden behind the stand).

Maintenance

Clean the surfaces of the camera and monitor with a soft dust-free cloth. Never use cleaning agents or solvents. If the units become dirty, use a lightly dampened cloth to wipe surfaces, taking care not to allow water into any openings.

Information on Disposal of Battery and Product

Do not attempt to repair or adjust any of the electrical or mechanical functions of the unit.

Dispose of the product in an environmentally responsible way. Take it to the collection points designated by local authorities. You can also contact the store where you purchased the product.

General Notes

All rights reserved. The features described in the user manual are subject to modifications without prior notice.

WARNING: Keep the small parts away from children.

Printed in China.