FCC Compliance Information Statement
[FCC Logo]
Product Information
VIGI 4MP Outdoor Full-Color 4G Bullet Network Camera
Model Number: InSight S345-4G
| Component Name | Model |
|---|---|
| I.T.E. Power | T120100-2B1 |
Responsible Party
Company: TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
"To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter."
TP-Link Systems Inc. has determined that the equipment shown above has been shown to comply with the applicable technical standards, FCC Part 15. There is no unauthorized change made in the equipment, and the equipment is properly maintained and operated.
Issue Date: 2025.08.28
Safety Information
- Keep the device away from fire or hot environments. [DO NOT] immerse in water or any other liquid.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact TP-Link Systems Inc.
- Do not use a damaged power adapter to charge the device.
- Do not use any other power adapters than those recommended.
- Adapter shall be installed near the equipment and shall be easily accessible.
- Do not use the device where wireless devices are not allowed.
- Adapter should be used indoors where the ambient temperature is lower than or equal to 40 ℃.
- Operating Temperature: -30 ℃ - 60 ℃
- This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device.
Please read and follow the above safety information when operating the device. TP-Link Systems Inc. cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Explanations of Symbols on the Product Label
Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbols may vary from products.
| Symbol | Explanation |
|---|---|
| [Class II equipment] | Class II equipment |
| [Class II equipment with functional earthing] | Class II equipment with functional earthing |
| ~ | Alternating current |
| --- | Direct current |
| [Polarity of d.c. power connector] | Polarity of d.c. power connector |
| ⌂ | For indoor use only |
| ⚡ | Dangerous voltage |
| ⚡ | Caution, risk of electric shock |
| VI | Energy efficiency Marking |
| ⏚ | Protective earth |
| [Earth] | Earth |
| [Frame or chassis] | Frame or chassis |
| [Functional earthing] | Functional earthing |
| ? | Caution, hot surface |
| ⚠ | Caution |
| ℹ️ | Operator's manual |
| ⏻ | Stand-by |
| [ON/OFF] | "ON"/"OFF" (push-push) |
| [Fuse] | Fuse |
| [Fuse in neutral N] | Fuse is used in neutral N |
| [WEEE Recycling Symbol] | RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. |
| ? | Caution, avoid listening at high volume levels for long periods |
| ? | Disconnection, all power plugs |
| m | Switch of mini-gap construction |
| μ | Switch of micro-gap construction (for US version) |
| ε | Switch without contact gap (Semiconductor switching device) |
