Kenmore Oscillating Fan Heater

Introduction

Please read this guide carefully. It will help you operate your new Kenmore Heater in the safest and most effective way. Keep this manual and your sales check (receipt) in a safe place for future reference.

Important Safety Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons. Read all instructions before using this Heater.

WARNING:

• This product is intended for indoor residential, office, and personal shop use only, not for industrial or other commercial applications.
• Use only with electrical wiring that is in good working order and meets applicable codes and ordinances. Consult a qualified electrician if you have questions about your wiring.
• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause electrical shock, fire, or injury.
• Do not operate the heater with a damaged power cord or plug, or after it malfunctions or has been dropped or damaged.
• Do not operate heater unattended. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction by a responsible person.
• Do not place the heater on a small, unlevel, uneven, or any surface that might allow it to tip or fall.
• For proper operation, place the heater on a smooth, non-combustible surface.
• Always unplug the heater when not in use.
• Do not operate heater with safety devices removed.
• Do not run the power cord under carpeting. Do not cover the cord with throw rugs, runners, or the like. Arrange the cord away from traffic areas where it will not be tripped over.
• Avoid the use of extension cords due to fire risk. If an extension cord must be used, it must be a minimum 14AWG and rated not less than 1875 watts.
• Do not insert or allow any object to enter any openings on the heater, as this may cause electric shock and/or fire hazard.
• Do not use with a damaged cord or plug. Use with an adequate electrical system that is up to code. The supply cord has a polarized plug (wide blade fits wide slot) as a safety feature. Match the wide blade to the wide slot and fully insert the plug. If the plug does not fit, contact a qualified electrician. Never use an extension cord. Do not attempt to defeat this safety feature.
• Do not operate any heater with a broken heating element or ceramic cone or any visual imperfections. For all repairs, contact a qualified service dealer.
• Do not operate heater with its ventilation obstructed.

SHOCK HAZARD:

• Use your heater only in dry environments. This heater is not intended for use in bathrooms, laundry areas, or similar locations near sinks, washing machines, swimming pools, or other water sources. Never locate the heater where it may fall into a bathtub or other water container. Do not use outdoors. Do not use in damp environments such as flooded basements.

HOT SURFACES:

• Do not touch the body of the heater when in use, as it is hot. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving the heater.

FIRE HAZARD:

• The heater has hot and arcing or sparking parts inside. Do not use near combustible materials or flammable gases or sources of heat. DO NOT USE in areas where gasoline, paint, or flammable materials are used or stored.
• Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front, sides, and rear of the heater.
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. Do not place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause electric shock, fire, or damage the heater.

CAUTION:

• Before cleaning the heater, be sure to disconnect the power cord and allow the heater to cool completely.
• Do not operate the heater without the grill in place. Do not use the heater if it has malfunctioned or become damaged in any way.

PET OWNERS NOTE: The health of birds and some small pets are extremely sensitive to the fumes given off during the initial use of many appliances. Although these fumes are not harmful to humans, it is recommended that this heater not be used around birds and small pets during its initial use until the manufacturing corrosion coatings burn off.

SAVE THESE INSTRUCTIONS!

Parts and Features

It is important to know your heater's parts and features to ensure its proper and safe use. Review these before using your heater.

Figure 1: Oscillating Fan Heater

The front panel displays the main components. On the top control area, there is a Thermostat Control dial and an ON/OFF Power Level Control dial. A Power Light Indicator is also located here. On the front, below the main grille, there is an Oscillation Control switch located on the heater base.

Operating Instructions

Heater Operation

Always operate the heater in the upright position following all instructions and recommendations listed in this manual.

Heater Location: Place the heater in the area of the room that is coldest.

Heater Connection: Plug the heater directly into a 120 Volt A.C. 60 Hz outlet. Ensure the plug fits tightly in the outlet. A loose connection may cause overheating and damage to the plug or heater. NOTE: To prevent overloading a circuit, do not plug the heater into a circuit that is servicing other electrical needs.

Turning the Heater On

To start the heater, turn the ON/OFF Power Level Control from the OFF position "O" to the "I" (Low) or "II" (High) setting. Then, rotate the Thermostat Control clockwise to the largest "." position. (During initial heater use, you may experience a slight odor or smoking. This is the result of the heating element lubrication "burning off". This is normal and will go away after a few minutes of use.)

Power Level Control

This heater has two heat settings: HIGH "II" (1500 watt) and LOW "I" (750 watt). Use the higher setting to raise the room temperature quickly. When the desired temperature is reached, turn the control to the LOW "I" setting to maintain a comfortable temperature.

Setting Thermostat

After the heater has been turned on and the area has reached the desired temperature, slowly rotate the Thermostat Control counterclockwise from the largest "." position until the heater shuts off (you should hear a faint "click"). By leaving the thermostat at this setting, it will automatically maintain this temperature. To maintain a lower temperature, rotate the control further counterclockwise. To maintain a higher temperature, rotate the control clockwise.

Turning Off

To discontinue use, turn the Power Switch to the "O" position. Always turn the heater OFF before unplugging or plugging in the heater. The heater should be unplugged when not in use.

Oscillation Control

You can control the Oscillation feature on the Fan Heater by moving the Oscillation switch located on the heater base to the "-" or "O" position. In the "-" setting, the heater body will swing slowly back and forth.

To Operate Fan Only

Turn the ON/OFF Power Level Control dial to the Fan "88" setting. Turn the thermostat control fully clockwise to the MAX position so that the fan will run continuously. Oscillation will function while in fan mode.

Important Safety Features

The power indicator light, located above the control panel, lights whenever the heater/fan is plugged in, indicating that the heater has power. The heater is equipped with an automatic overheat protection device. If the heater grill is obstructed, or if the heater gets too hot for any reason, this device will turn the heater off. To reset, turn the ON/OFF Power Level Control to "O", unplug the heater, and wait 10 minutes for it to cool down. Plug it back in and turn the control to an operating position. To prevent further automatic shut-off, ensure the air inlet grill (back of heater) is spaced far enough from walls or other objects to allow for sufficient airflow. Always place the heater on a smooth, level surface. The heater is also equipped with a safety tip-over switch that turns power off to the heater when it tips over. To resume heater functions, simply stand the heater upright. With tip-over protection, the heater will only operate when placed upright on a level surface.

Care and Maintenance

Cleaning

CAUTION:

The heater should be cleaned at least once a year to maintain proper performance. Clean the outside surface with a damp cloth. Allow the heater to dry completely before use. Do not use harsh chemical or abrasive cleaners.

WARNING:

CAUTION:

Repair

Do not attempt to open the heater to clean or service the inside. If the heater does not function normally, call the customer assistance number to arrange for possible heater service and repair: 1-866-877-1889.

Storage

Keep the original carton for storage of the Fan Heater. Coil and tie the power cord to avoid damage during storage.

Kenmore Limited Warranty

FOR ONE YEAR from the date of sale, this product is warranted against defects in material or workmanship.

WITH PROOF OF SALE, return a defective product to the retailer from which it was purchased for free replacement.

This warranty is void if this product is ever used for other than private household purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179