LiteBee Kids Drones | Professional Programming Drone for Kids| Coding for KidsEducational drone Coding for Beginners | Support-litebee wing
User Manual for LiteBee models including: Wing Electromagnet Module, Wing, Electromagnet Module, Y-17
LiteBee WingKit di consegna dell'elettromagnete, 159.00 Fr.
21 juil. 2022 — The electromagnet extension is an additional accessory for LiteBee Wing. It can lift and drop the iron materials by its electromagnet.
Packing list Specification Model: Y17-AI Size: 40*40*8mm Working voltage/current: 5V/@80mA Size of QR code: 24*30cm Max load: 500g Actual load: 0-8g
File Info : application/pdf, 16 Pages, 8.06MB
DocumentDocumentElectromagnet Module Product Manual CONTENTS 1 Product introduction 01 Brief introduction 4 Installation 06 Installing steps 2 About the product 02 Packing list 02 Specification 5 Programming 11 Reference case 3 Firmware 03 Firmware version 05 Firmware updating Product introduction The electromagnet extension is an additional accessory for LiteBee Wing. It can lift and drop the iron materials by its electromagnet. Combined with the drone, the extension also can be programmed to transfer the matrials automatically. This extension provides a chance for kids to practice their programming skill and learn how the programming can be applied. 01 ABOUT THE PRODUCT Packing list Electromagnet unit*1 Counterweight holder*1 Electromagnet holder*1 Long bolt*8 Connecting cable*1 Short bolt*8 Nylon screw*2 Nut*2 Specification Model: Y17-AI Size: 40*40*8mm Working voltage/current: 5V/@80mA Size of QR code: 24*30cm Max load: 500g Actual load: 0-8g Electromagnet*1 QR code for position*15 Adsorbate*20 02 PREPARATION Firmware version Description To apply the electromagnet, the firmware version of drone and controller should be V1.1.0 and up, the version of PC software - LiteBee Go should be V0.2.1 and up. How to check the version Link the drone to controller Connect the controller with computer by USB cable Switch to programming mode Click the exclamation mark to make sure the controller connected(pic 3) Choose "LiteBee Wing" mode Click the "Add Extension" (pic 1) Check the version on the button line of LiteBee Go(pic 4) FV shows the version of the aircraft RV shows the version of the controller 03 Start LiteBee Go pic 1 pic 3 pic 2 pic 4 04 How to update the version To download the corresponding document for firmware upgrading on LiteBee official web Or, you can find relevant video for firmware upgrading on YouTube channel - LiteBee, search "Guide for firmware upgrade" Official Website:https://www.litebee.com/product/liteBeeWing/download 05 pic 5 INSTALLATION 1 2 *4 3 *1 *1 *1 *1 Disassemble these arms of rotor Remove these short bolts. Replace them by long bolt And then reassemble it. Fix the electromagnet on the holder with a screw Tighten the screw until it can't twist. 06 4 *1 5 *4 6 *1 *1 Fix the counterwight holder on the front Fix the electromagnet on the back. 07 Insert 4 short bolts into the bottom of the drone. Insert the connecting cable into the electromagnet unit. 7 8 9 Install theelectromagnet unit on the bottom of the drone Attention: the blank side face to the bottom of the drone. Insert the cable into the broadside of the drone. Connect the power line with the electromagnet unit. 08 Finished 09 EXTENSION PROGRAMMING Step 1: Connect the drone with computer Link the drone with the controller first Connect the controller with computer by USB cable Step 2: Electromagnet mode Start LiteBee Go Click "Add extension" Click "Identification card + attract and lift" PS: If there is a green tick mark, connected; if a orange exclamation, click the exclamation to connect again. 10 Reference case Task Let the drone fly to the QR code No.0 and hover; then land and turn on the electromagnet and lift the adsorbate; take off again and fly to the QR code No.10; hover and turn off the electromagnet to drop the adsorbate; land. Case Mind map Start Calibrate Take off and fly forward When recognized the QR code No.10 yes Hover for 2 seconds when recognized the QR code No.0 yes Hover for 5 seconds Turn off the electromagnet Autoland 10 Autoland Turn on the electromagnet 11 Take off and fly forward Manufacturer: Shenzhen Makerfire Technology Co., Ltd. Website: www.litebee.com Tel: 44-830-2598 Email: sales@litebee.com Address: 25th Floor, A7 Building, Creative City, Liuxian Ave, Xili Street, Nanshan District, Shenzhen, China.