Onn. 50" – 86" Tilting TV Wall Mount

Before Getting Started

Ensure this mount is suitable for your TV and wall type.

TV Compatibility Check:

• VESA Pattern: Must be equal to or greater than 75mm x 75mm (2.95" x 2.95") and equal to or less than 600mm x 400mm (23.62" x 15.75").
• Weight Capacity: Your TV (including accessories) must weigh less than 120 lbs (54.4 kg).

Wall Type Check:

• Suitable for drywall with wood studs or concrete, stone, or masonry walls.
• CAUTION: DO NOT install into drywall alone.

Installation Tools (Not Included):

Phillips Screwdriver, Drill, Tape Measure, Level, Pencil, Socket Set (1/2"), Wood Stud Finder, 5/32" Wood Drill Bit, 3/8" Masonry Drill Bit, Hammer.

Safety Caution:

• Keep this guide for future reference.
• Never let children climb on or play with the product.
• Do not sit or stand on the product.
• Do not fasten a TV heavier than the recommended load rating.
• Use suitable concrete, stone, masonry wall, or wood stud wall ONLY. Not suitable for metal studs or drywall alone.
• Improper installation may cause property damage and/or personal injury.
• Two people are recommended for installation.
• Improper handling can result in cuts or lacerations.

For assistance, call 1-888-516-2630 (7 a.m. - 9 p.m. CST).

Dimensions

Product Overview

Diagram showing the general layout of the TV mount attached to a wall and a TV.

Wall Plate Dimensions:

Width: 16.00" (406.40mm), Height: 12.00" (304.80mm). Mounting hole pattern: 24.00" (609.60mm) wide, 8.00" (203.20mm) high.

VESA Interface Dimensions:

Maximum VESA: 600mm (23.62"), Minimum VESA: 75mm (2.95"). Maximum VESA height: 400mm (15.75"), Minimum VESA height: 75mm (2.95").

Side View - Tilt:

Shows a side profile of the mount, indicating a tilt range of +12° to -12°.

Fully Assembled Mount Dimensions:

Width: 25.79" (655mm), Height: 16.93" (430mm). Depth from wall: 4.02" (102mm).

Assembly Tips:

1. Read the entire Product Guide before installation.
2. Verify all parts are present and in good condition.
3. Assemble on a flat, protected surface (e.g., carpet or original carton).
4. Do not install on a sloping surface.
5. Two people are recommended for assembly.

CAUTION: This mount supports a maximum weight of 120 lbs. The wall must support 4X the standard weight. Do not overtighten screws. Using products heavier than the maximum weight may cause collapse and injury.

Parts List

• A: Wall plate (x1)
• B: Left TV bracket (x1)
• C: Right TV bracket (x1)
• D: Hanging template (x1)

Wall Mounting and TV Bracket Assembly Hardware:

• E: M7x55mm Lag bolt (x4)
• F: Anchor 10x50mm (for concrete, stone, or masonry installation only) (x4)
• G: Allen wrench (x1)

TV Mounting Hardware:

TV Screws:

• M4x12mm (H1 x4)
• M6x12mm (H2 x4)
• M8x20mm (H3 x4)
• M4x35mm (H4 x4)
• M6x35mm (H5 x4)
• M8x35mm (H6 x4)
• M8x45mm (H7 x4)

Spacers:

• M8x5mm (J1 x4)
• M8x5mm (J2 x4)

Washers:

• M4 (T1 x4)
• M6/M8 (T2 x4)

STEP 1: Attach TV Brackets & to TV

CAUTION: Lay TV face down on a soft, non-abrasive surface.

CAUTION: Ensure TV brackets are centered and level on the TV back.

1.2 Select TV Screws

Choose screws that fit your TV's mounting holes. Use spacers and washers if needed. Refer to the diagrams for correct screw, spacer, and washer combinations for short screws (no spacer needed) and long screws (spacer needed).

1.3 Attach Both TV Brackets

Attach brackets B and C to the TV using the appropriate screws (H1-H7), spacers (J1-J2), and washers (T1-T2) as indicated in the diagrams. Discard any unused hardware.

STEP 2: Attach Wall Plate A to Wall

STEP 2A: Wood Stud Installation

NEVER USE ANCHOR F FOR WOOD STUD ASSEMBLY.

CAUTION: Wood stud minimum size is 2x4"; surface covering cannot exceed 5/8". Drill into the wood stud center line.

1. 2A.1 Confirm stud location: Use a stud finder to locate the center of the wood stud.
2. 2A.2 Mark holes: Hold hanging template D at the desired position, use a pencil to mark 4 hole locations, ensuring it is level.
3. 2A.3 Pre-drill holes: Drill 4 holes using a 5/32" (4.0mm) Wood Drill Bit to a depth of 2.36" (60mm) on the marked center line.
4. 2A.4 Fix Wall plate: Attach wall plate A to the wall using M7x55mm lag bolts E and a 1/2" socket set.

STEP 2B: Concrete, Stone, or Masonry Installation

CAUTION: Concrete wall minimum thickness is 5.5"; surface covering cannot exceed 3/8".

CAUTION: Anchors F are for concrete, stone, or masonry walls ONLY. Do not install into wood studs.

CAUTION: Install only on a perpendicular wall. Do not install on the ceiling.

1. 2B.1 Mark holes: Hold hanging template D against the wall at the desired position and mark 4 hole locations with a pencil, ensuring it is level.
2. 2B.2 Pre-drill holes: Drill 4 holes using a 3/8" (10mm) Masonry Drill Bit to a depth of 2.36" (60mm).
3. 2B.3 Insert Anchors: Insert anchors F into the drilled holes and tap lightly with a hammer.
4. 2B.4 Fix Wall plate: Attach wall plate A to the wall using M7x55mm lag bolts E and a 1/2" socket set.

STEP 3: Hang and Secure TV on Wall Plate

1. 3.1 Test Wall plate: Gently pull the wall plate to ensure it is securely mounted to the wall. (Supports up to 120 lbs / 54.4 kg).
2. 3.2 Hang TV: Hang the pre-assembled TV unit onto the wall plate A. Pull down the release cords until the latches click into place. CAUTION: This step requires 2 or more people.
3. 3.3 Adjust Tilt: Loosen the handles on the TV brackets to tilt the TV to the desired angle. Tighten the handles after adjustment. Tilt range is +12° to -12°.