DIGITAL PROJECTION ALARM CLOCK

INDEX

1. FEATURES
2. START UP
3. SETTINGS
1. Time Setting (Turn off the radio)
2. Night Mode Setting
3. Alarm Setting
4. FM Radio
1. FM Setting
2. Sleep Timer
5. Use Projection
6. Brightness Control
7. Charging
4. RESTORE FACTORY DEFAULT
5. PRECAUTION

START UP

Please remove plastic insulator tab from button battery compartment in the back and connect the AC/DC adaptor to the power supply and the other end to the USB seat on the back of the clock, then the clock starts to work.

Note: When the power is off, the LED screen won't show, the radio and alarm cannot work. The backup battery only retains the basic settings of time and alarm.

Front view: Buttons include TIME, RADIO/SLEEP, ALARM 1/2, SNOOZE/DIMMER, SET, VOL, UP/PROJECT, DOWN.

Back view: Features USB CHARGING PORT, INSERT DC JACK TO POWER UP YOUR UNIT, INSERT 1X CR2032 LITHIUM BATTERY (INCLUDED).

Top view: Buttons include UP/PROJECT, DOWN, VOLUME, RADIO/SLEEP, SNOOZE/DIMMER, SET, ALARM 1,2.

SETTINGS

Time Setting (Turn off the radio)

1. Press and hold the "SET" button for 3 seconds. The hour digits flash. Press "▲" or "▼" to set the hour. (Long press "▲" or "▼" to accelerate setting at high speed.)
2. Press "SET" again. The minute digits flash. Press "▲" or "▼" to set the minute. (Long press "▲" or "▼" to accelerate setting at high speed.)
3. Press "SET" again. The display screen shows "24 H" and flashes. Press "▲" or "▼" to select "12 H" or "24 H".
4. Press "SET" again. The display screen shows "09" and flashes. Press "▲" or "▼" to select your snooze time from 5 to 60 minutes.
5. Press "SET" or wait for 20 seconds without any operation to exit the current setting mode.

Note: When the 12-hour time format is selected, the "PM" LED will appear on the screen in the afternoon.

Night Mode Setting

1. Night mode means that the LED automatically enters a low brightness display status at night.
2. In LED Time display mode, press "SET" once to turn on the night mode setting. Select "ON" or "OFF" by pressing "▲" or "▼" manually. The default period is from 18:00 to 6:00 the next day, during which it will automatically enter the lowest brightness display status.
3. When night mode is "ON", press and hold the "SET" button for more than 3 seconds to enter the interval time setting mode. The setting sequence is: "start hour" - "start minute" - "end hour" - "end minute". At the start hour and minute setting status, the upper point in the center of the screen is long bright. At the end hour and minute setting status, the lower point in the center of the screen is flashing (Same as time setting).

Note: Auto Brightness Mode and Night Mode cannot be turned on simultaneously. If you need to make Night Mode settings, please ensure the dimming setting (Brightness Mode) is manual. You can choose any time for interval time setting.

Alarm Setting

1. Press "AL" once. The ■1 and the hour digits will flash. Press "▲" or "▼" to set the hour duration. (Long press "▲" or "▼" to accelerate setting at high speed.)
2. Then press "AL" to set minutes. Press "▲" or "▼" to set the minute duration. (Long press "▲" or "▼" to accelerate setting at high speed.)
3. Then press "AL". The LED displays "OFF" (alarm off). Press "▲" or "▼" to select the alarm mode ("rd" = wake-to-radio, "bu" = wake-to-buzzer, "OFF" = alarm off. When "rd" or "bu" is selected, the related alarm will turn on.)

Note: If you select the radio as the alarm tone, the volume of the alarm will start from L01 and rise to the volume you played last time gradually (Enhance one level every 10 seconds).

4. If you need a second alarm clock, please repeat steps 1-3. (Note: The second alarm clock is reflected as "■2" on the display screen.)
5. Press "AL" or wait for 20 seconds without any operation to exit alarm setting mode.
6. When alarm "ALARM 1" or "ALARM 2" is setting, there will be a ■1 or a ■2 LED on the bottom of the display.
7. When alarm 1 or 2 is sounding, the related "■1" or "■2" LED flashes. Press "RADIO/SLEEP" or "AL" once to stop the alarm, and it will sound on the following day. The related icon will not disappear. When the alarm is sounding, press "SNOOZE/DIMMER" once, the alarm will be silent and come on again after the set snooze duration (Default snooze duration is 9 minutes; you can set it according to the fourth point of "Time Setting").

Note: 1. If your second alarm activates while the first alarm is sounding or it is in snooze mode, the second alarm will override the first alarm (The first alarm is reset to come on the next day). 2. Turn on and turn off AL alarm. Press "▼" to select. (There is a "■" symbol in the display for ON condition and no "■" symbol for OFF condition. The sequence is "■1" ON - "■2" ON - "■1" OFF - "■2" OFF).

FM Radio

FM Setting

1. Unfasten the Antenna in the back and position it in different directions until a stable radio signal is received.
2. Press "RADIO/SLEEP" once to play the radio. The display shows "ON" and then the radio frequency readings in MHz (From 76.0 MHz - 108 MHz).
3. Press "SET" briefly. The FM radio will scan and automatically save frequencies as 01, 02, 03.... It will stay on the first station once the scan is completed.
4. Press "▲" or "▼" to choose a stored station.
5. To adjust the volume, press "VOL" briefly. The display shows "L07". Press "▲" or "▼" to adjust the volume from L00 (minimum) to L15 (maximum).
6. Press "SNOOZE/DIMMER" to turn off the radio.
7. It has unlimited memory. Press "SET" again, it will override the previous settings.

Note: 1. The station you played last time will be stored as an alarm tone. 2. Keep your radio away from interference sources or other electronic devices that may cause interference to the radio.

Sleep Timer

1. Press "RADIO/SLEEP" twice to enter sleep mode. The sleep LED "SL" and sleep time "05" (5 minutes) appear on the display.
2. Then press the "RADIO/SLEEP" to adjust the sleep timer from 5, 15, 30, 45, 60, 75, 90, or OFF.
3. When the display screen changes back to show the time, press the "RADIO/SLEEP" twice to show the remaining sleep time.
4. The radio will play for the programmed sleep time and then shut off automatically.

Use Projection

1. In clock mode, press "▲" once in AC mode to turn on the projection (bright). Press again to adjust the brightness of the projection (From bright - slightly bright - dim - off; default is off).
2. When the projection is on, press and hold "▲" to revolve the projection view. Long press the project key to rotate the projection 180 degrees.

Note: There is no projection function in battery-powered mode.

Brightness Control

In clock mode, press "SNOOZE/DIMMER" once to adjust the brightness of the LED display.

1. Slightly Bright (default) -- Bright -- Off -- Dim
2. Press and hold the "SNOOZE/DIMMER" button for 2 seconds to select the on/off of Auto mode. If "AU" is selected, the LED display will automatically enter low brightness mode in the dark environment. If "OFF" is selected, brightness can only be controlled manually (default is "OFF").

Note: This can only be done when the radio is off and the unit is not sounding.

Charging

Connect the charging cable of your mobile phone to the USB port at the back of the unit, then connect the other end to your mobile phone or other equipment. The clock radio will charge the mobile phone automatically.

Notes

1. Use the original cable of your mobile phone for charging.
2. Charging with this USB jack may take a long time.

RESTORE FACTORY DEFAULT

If a time error occurs, it may be subject to electrostatic interference from other equipment. To resolve this, you can remove the power supply and the backup battery. Then the clock can be restored to Factory Default. Repower the clock and set the functions.

PRECAUTION

1. Do not place the electronic clock in a high temperature, water, or direct sunlight environment.
2. When placing the clock on furniture, use a cloth or other protective material to keep it away from the furniture.
3. If necessary, use a flannel with a little soapy water to clean the clock. Substances such as gasoline, thinner, or similar liquids will damage the clock's surface. Cut off the power before cleaning.
4. If you do not use this clock for a long time, such as a month or even longer, remove the battery to prevent the clock from being corroded. If the battery compartment is corroded or dirty, clean and replace the battery in time.
5. Do not disassemble this product.